thread pitch chart

Thread Pitch Chart: Complete Guide to Metric & Imperial Sizes

By John King
AD

A thread pitch chart is one of those quiet reference tools that rarely gets attention until a bolt refuses to thread, a nut spins uselessly, or a fitting leaks under pressure. Whether you are restoring a vintage motorcycle, machining a custom bracket, or simply matching a replacement screw at a hardware store, knowing the pitch of a thread tells you precisely how the fastener will behave. The chart itself is nothing more than a lookup table, but the information inside it saves hours of guesswork and prevents expensive damage.

This guide breaks down how thread pitch charts work, how to read them across both metric and imperial systems, and how to apply them in real-world situations. By the end, you will understand why two bolts of identical diameter can be completely incompatible, and you will know exactly where to look when the numbers matter.

Understanding Thread Pitch Fundamentals

Thread pitch describes the distance between one thread crest and the next, measured along the axis of the fastener. In the metric system, that distance is expressed in millimeters, so an M8 x 1.25 bolt has threads spaced 1.25 millimeters apart. This single number dictates how many complete rotations the nut must make to travel a given distance, and therefore how quickly the fastener tightens.

AD
Thread Pitch Charts
Thread Pitch Charts
Thread Profiles
Thread Profiles
Metric Thread Chart: A Complete Guide +Pdf
Metric Thread Chart: A Complete Guide +Pdf

The diameter alone is never enough to identify a thread. Two bolts can both measure 8 millimeters across the shank yet have completely different pitches, and forcing the wrong nut onto the wrong bolt will strip the threads on both. This is why any serious thread pitch chart pairs the nominal diameter with its corresponding pitch rather than listing dimensions in isolation.

Thread Pitch Versus Threads Per Inch

Imperial and Unified threads take a different approach. Instead of measuring the gap between crests, they count how many complete threads fit within one inch of length. A 1/4-20 bolt, for example, has twenty threads per inch. The higher the second number, the finer the thread and the closer together the crests sit.

a table with measurements for the top drill size chart
a table with measurements for the top drill size chart
BSP vs NPT thread - Knowledge - Yuyao Jiayuan Hydraulic Fitting Factory
BSP vs NPT thread - Knowledge - Yuyao Jiayuan Hydraulic Fitting Factory
The Machinist - The Machinist knowledge | Facebook
The Machinist - The Machinist knowledge | Facebook

Converting between the two systems is straightforward once you know the relationship. Dividing 25.4 by the threads-per-inch value gives you the equivalent pitch in millimeters. A 1/4-20 fastener works out to roughly 1.27 millimeters of pitch, which is why it feels so similar in handling to a metric coarse thread of comparable size.

Coarse Threads Versus Fine Threads

Every standard diameter typically offers at least two pitch options. Coarse threads have wider spacing, deeper engagement, and are far more forgiving when you are assembling parts in awkward positions. They resist cross-threading, tolerate minor surface damage, and are the default choice for general fastening in soft materials like aluminum and cast iron.

AD

Fine threads, by contrast, pack more crests into the same length. They provide greater tensile strength because the minor diameter of the bolt is larger, and they hold torque better under vibration. Automotive suspension components, hydraulic fittings, and precision instruments frequently rely on fine pitches for exactly these reasons, even though they demand more care during assembly.

Metric Thread Chart For Metric Bolt Sizes - Accu Limited
Metric Thread Chart For Metric Bolt Sizes - Accu Limited
the table shows the number and percentage of people in each country
the table shows the number and percentage of people in each country
Tap Drill Chart
Tap Drill Chart
an old diagram shows the different types of threadd forms and their corresponding lines, which are
an old diagram shows the different types of threadd forms and their corresponding lines, which are
BSP vs NPT thread - Knowledge - Yuyao Jiayuan Hydraulic Fitting Factory
BSP vs NPT thread - Knowledge - Yuyao Jiayuan Hydraulic Fitting Factory
the table shows that there are many different types of threads and sizes for each thread
the table shows that there are many different types of threads and sizes for each thread

How to Read a Thread Pitch Chart

A well-organized thread pitch chart is divided into system, diameter, and pitch, with columns for both coarse and fine options where applicable. The first column lists the nominal size, the second gives the standard coarse pitch, and the third provides the fine alternative. Some charts add a fourth column showing the thread angle, which is 60 degrees for both ISO metric and Unified inch threads.

Reading the chart correctly means identifying your measurement system before anything else. A caliper reading of 10 millimeters points you toward the metric table, while a reading near 0.394 inches points you toward the imperial table. Mixing the two systems is the single most common source of ordering errors in workshops and supply rooms.

AD

Metric Thread Pitch Essentials

ISO metric threads follow a predictable progression that most engineers memorize within a few months on the job. Small diameters use fine pitches by default, while larger diameters scale up in steps that keep the thread depth proportional to the shank. The table below covers the sizes you will encounter most often.

THREAD CALCULATION
THREAD CALCULATION
Measuring Thread Pitch & Threads Per Inch | Fasteners 101
Measuring Thread Pitch & Threads Per Inch | Fasteners 101
the different types of threads are shown in this diagram, with instructions on how to use them
the different types of threads are shown in this diagram, with instructions on how to use them
Bolt & Screw Sizes
Bolt & Screw Sizes

Note that metric fine pitches exist for nearly every diameter, and they are written as a second number after the diameter, such as M10 x 1.25. When a chart lists only one pitch for a given size, it is almost always the coarse standard. If the part you are replacing came from European equipment, check the fine column before assuming coarse.

Metric SizeCoarse Pitch (mm)Fine Pitch (mm)Common Application
M30.500.35Electronics, small brackets
M40.700.50Instrument panels, enclosures
M50.800.50Appliance hardware
M61.000.75General machinery
M81.251.00Automotive brackets
M101.501.25Structural fastening
M121.751.25Heavy equipment, chassis

Unified Inch Thread Reference

Unified National threads, designated UN, UNC, or UNF, dominate North American hardware. The coarse series carries the UNC suffix, while the fine series uses UNF. A 3/8-16 bolt is coarse, and a 3/8-24 bolt is fine. Both share the same nominal diameter, so the chart must be consulted rather than guessed.

AD

Pipe threads follow a separate standard entirely, which trips up many newcomers. NPT fittings are sized by pipe bore rather than outside diameter, and their pitch is fixed per size. If you are working with fluid lines, use a dedicated pipe thread chart instead of a general fastener chart, because the taper and sealing behavior are fundamentally different.

Applying Pitch Data in the Workshop

Charts are only useful when paired with accurate measurement. Before you consult any table, confirm the outside diameter of the male thread with a caliper, then verify the pitch with a gauge or by counting threads over a known length. Two minutes of measurement prevents a wasted trip to the supplier and a damaged component.

Thread pitch also influences torque specifications. A fine thread generates more clamping force for the same applied torque, which means the recommended tightening values differ between pitch variants of the same diameter. Never substitute a fine thread bolt for a coarse one without checking the torque table, especially on safety-critical assemblies.

Measuring Thread Pitch Accurately

A thread pitch gauge is a set of thin metal leaves, each cut with teeth matching a specific pitch. You press successive leaves against the threads until one seats perfectly with no rocking and no gaps. The number stamped on that leaf is your pitch. Gauges are inexpensive, pocket-sized, and far more reliable than eyeballing.

If you do not have a gauge, measure with a steel rule instead. Count the number of complete threads across one inch for imperial fasteners, or measure the distance spanning ten thread crests and divide by ten for metric fasteners. The longer the span you measure, the smaller your margin of error becomes.

Common Mistakes When Using a Pitch Chart

The most frequent error is assuming diameter equals thread size. A 10 millimeter bolt is not automatically M10, and a half-inch bolt is not automatically 1/2-13. Always cross-reference the diameter with the pitch column rather than stopping at the first match you find.

Another trap is confusing pitch with lead, particularly on multi-start threads. Lead describes how far the nut travels in one full rotation, which on a two-start thread is twice the pitch. Standard fasteners are single-start, so pitch and lead are identical, but lead screws and specialized motion components break that assumption.

Keep a printed thread pitch chart near your workbench and a digital copy on your phone, and you will find that the small friction points of matching hardware largely disappear. The next time a fastener does not seat properly, resist the urge to force it. Measure the diameter, check the pitch, and let the chart tell you what you are actually holding. That habit alone will save you more stripped threads than any tool in your box.

AD