m6 bolt dimensions

M6 Bolt Dimensions: Complete Guide to Sizes, Thread Pitch, and Specs

By Mark Smith
AD

M6 bolt dimensions are a frequent reference point for engineers, mechanics, and DIY builders because the M6 size sits in a practical middle ground: compact enough for tight assemblies, yet strong enough for countless mechanical and structural tasks. Whether you are replacing a lost fastener, designing a bracket, or specifying hardware for a production run, knowing the exact measurements behind an M6 bolt helps you avoid stripped threads, poor fit, and weak joints. The term M6 is simple, but the complete dimensional picture includes thread pitch, head size, length measurement, clearance holes, and matching nut or washer dimensions.

Metric fasteners follow internationally recognized standards, and M6 hardware is no exception. A bolt marked M6 can still vary in head style, thread length, material, and tolerance class, so two M6 bolts may look quite different while sharing the same nominal thread diameter. This guide breaks down the most important M6 bolt dimensions in plain language, covering common hex bolts, socket head cap screws, nuts, washers, and clearance holes so you can choose the right component with confidence.

M6 Bolt Dimensions Explained: Thread and Length Basics

At its core, M6 refers to a metric thread with a nominal major diameter of 6 millimeters. That 6 mm measurement is the theoretical outside diameter of the external thread, not necessarily the exact dimension you will see on a caliper. Real-world M6 bolts are manufactured within tolerance ranges, and a typical commercial M6 bolt may measure slightly under 6 mm across the thread crest. The difference is intentional because it allows the bolt to thread smoothly into a matching nut or tapped hole without binding.

AD
Bulong
Bulong
0.67US $ 25% OFF|Stainless Steel Flat Screw Phillips M6 | Flat Head M3 Stainless Steel Screw - Screws - Aliexpress
0.67US $ 25% OFF|Stainless Steel Flat Screw Phillips M6 | Flat Head M3 Stainless Steel Screw - Screws - Aliexpress
the different types of drills are shown in this graphic diagram, which shows how to use them
the different types of drills are shown in this graphic diagram, which shows how to use them

The thread form is also defined by pitch, which is the distance from one thread crest to the next. For a standard M6 bolt, the coarse pitch is 1.0 mm, written as M6 x 1.0. There is also a fine pitch option of 0.75 mm, often written as M6 x 0.75. Coarse threads are more common, easier to install, and less prone to cross-threading, while fine threads offer slightly greater resistance to vibration loosening and can provide finer adjustment in precision assemblies.

Nominal Diameter and Thread Pitch

The nominal diameter of 6 mm is the anchor point for every other M6 dimension. External threads are usually produced to a tolerance class such as 6g, which means the actual major diameter may fall roughly between 5.79 mm and 5.97 mm. The pitch diameter, which is the effective diameter where the thread flanks engage, is smaller than the major diameter and is critical for load transfer. Internal threads in a nut or tapped hole use a corresponding tolerance class such as 6H, ensuring that a standard M6 bolt will mate correctly without excessive play.

Lot de 10 vis M6 x 20 mm, boucles de ceinture, boulons de fixation, vis de fixation, attaches en cuir pour meubles, selles en cuir pour trous de 8 mm de diamètre
Lot de 10 vis M6 x 20 mm, boucles de ceinture, boulons de fixation, vis de fixation, attaches en cuir pour meubles, selles en cuir pour trous de 8 mm de diamètre
Wish | Shop and Save
Wish | Shop and Save
the measurements for different types of pipe fittings and their corresponding sizes are shown in this diagram
the measurements for different types of pipe fittings and their corresponding sizes are shown in this diagram

Pitch selection affects both the bolt and the hole you need. For an M6 x 1.0 coarse thread, the recommended tap drill size is typically 5.0 mm. For an M6 x 0.75 fine thread, the tap drill is usually 5.25 mm. Using the wrong drill size can lead to weak threads, difficult tapping, or a fastener that never reaches proper torque. If you are working with an existing threaded hole, confirm the pitch before buying a replacement bolt, because coarse and fine M6 threads are not interchangeable.

Length Measurement and Thread Length

Bolt length is measured differently depending on the head style. For most hex bolts and socket head cap screws, the length is measured from the underside of the head to the tip of the bolt. The head height is not included in the nominal length. For flat head or countersunk screws, however, the length is generally measured as the overall length because the head sits flush with the mating surface. This distinction matters when calculating grip length, which is the thickness of the material being clamped plus any washers.

AD

Thread length also varies. Fully threaded M6 bolts, such as those made to ISO 4017, have thread running from the tip nearly to the head. Partially threaded bolts, such as ISO 4014 hex bolts, have an unthreaded shank near the head. For a partially threaded M6 bolt, the thread length is commonly about 18 mm, following the general formula of twice the diameter plus 6 mm. Shorter M6 bolts are often fully threaded, while longer bolts are more likely to be partially threaded to provide a stronger shank in shear applications.

screw head cap screw bolt size chart
screw head cap screw bolt size chart
PP Polypropylene Hex Head Bolts M3 M4 M5 M6 M8 Insulation Plastic Hex Screws for Chemical
PP Polypropylene Hex Head Bolts M3 M4 M5 M6 M8 Insulation Plastic Hex Screws for Chemical
Metric Bolts Chart
Metric Bolts Chart
screws are lined up on a table with measurements for the size and length in front of them
screws are lined up on a table with measurements for the size and length in front of them
the diagram shows how to use an electrical device for measuring voltages and current lines
the diagram shows how to use an electrical device for measuring voltages and current lines
an image of some metal parts and measurements
an image of some metal parts and measurements

Head, Drive, and Clearance Dimensions for M6 Fasteners

Head dimensions determine how an M6 bolt interacts with tools, surrounding components, and the clamped surface. A hex head bolt requires a wrench or socket, while a socket head cap screw uses a hex key and fits into a counterbore. Button head and flat head versions offer lower profiles for cosmetic or space-constrained assemblies. Each head style has its own diameter, height, and drive size, so an M6 thread does not automatically mean the head will fit the same recess or tool.

Clearance holes and mating hardware are equally important. If the hole in the clamped part is too small, the bolt will not pass through; if it is too large, the joint may shift under load. Nuts and washers must also match the M6 thread and the intended bearing surface. The following dimensions cover the most common M6 fasteners used in machinery, automotive, furniture, and electronic enclosures.

AD

Hex Head and Socket Head Dimensions

A standard M6 hex head bolt typically has a width across flats of 10 mm, meaning you need a 10 mm wrench or socket. The head height is usually about 4 mm, and the width across corners is approximately 11.55 mm. These dimensions come from common standards such as ISO 4014, ISO 4017, and DIN 933 for fully threaded versions. The 10 mm across-flats size is one of the most recognizable features of an M6 hex bolt, and it helps distinguish it from an M5 bolt, which usually uses an 8 mm wrench.

an image of screws and nuts with measurements
an image of screws and nuts with measurements

An M6 socket head cap screw, often made to ISO 4762 or DIN 912, has a cylindrical head with a hex socket drive. Its head diameter is typically 10 mm, head height is about 6 mm, and the hex key size is 5 mm. A button head socket screw generally has a head diameter near 10.5 mm, a head height around 3.3 mm, and a 4 mm hex drive. Flat head socket screws for M6 commonly have a head diameter near 12 mm and a 90-degree countersink angle, allowing them to sit flush when installed in a matching chamfer.

Nuts, Washers, and Clearance Holes

A standard M6 hex nut usually has a width across flats of 10 mm and a height of about 5 mm, matching the 10 mm wrench used on the bolt head. Nylon insert lock nuts are often slightly taller, commonly around 6 mm, because they contain a locking element. A plain M6 washer typically has an inner diameter of about 6.4 mm, an outer diameter near 12 mm, and a thickness around 1.6 mm. These matching dimensions help distribute clamping force and prevent the nut or bolt head from damaging the surface.

AD

For clearance holes, ISO 273 defines several common sizes for M6 bolts. A close-fit hole is usually 6.4 mm, a medium-fit hole is 6.6 mm, and a free-fit hole is 7.0 mm. The best choice depends on alignment requirements and manufacturing tolerances. Tightening torque also matters: a property class 8.8 M6 bolt is often tightened to roughly 10 Nm in dry steel applications, while stainless steel M6 bolts may require a lower torque to avoid galling or thread stripping. Always verify torque values against the specific material, lubrication, and standard being used.

With these M6 bolt dimensions in hand, you can move from guesswork to precise selection. Check the thread pitch before matching a nut, measure length from the correct reference point, and confirm that the head style fits your tool and clearance requirements. A small fastener can carry a surprising amount of responsibility in an assembly, and using the right M6 hardware the first time keeps your project safer, stronger, and easier to maintain.

AD