Metric Drill Bit Sizes Explained: Your Complete MM Drill Bit Chart
Metric drill bit sizes are the standard way to specify drill diameters in most of the world, from Europe and Asia to Latin America and beyond. Instead of fractional inches or lettered gauges, these bits are labeled by their diameter in millimeters, such as 3.0 mm, 5.5 mm, or 10.0 mm. That simple decimal format makes it easier to match a bit to a metric fastener, bushing, dowel, or tapped hole without converting between three different measurement systems.
Whether you are building furniture, repairing a bicycle, tapping an M8 thread, or working on a 3D-printed assembly, knowing how metric drill bit sizes are organized saves time and prevents ruined holes. The challenge is not the metric system itself; it is understanding which size to grab for a given task. This guide breaks down the sizing conventions, compares metric bits with inch and gauge sizes, and explains how to choose the right diameter for tapping, clearance, and pilot holes.
Understanding Metric Drill Bit Sizes
Metric drill bits are sold by nominal diameter in millimeters. A 6.0 mm bit is intended to drill a hole approximately 6.0 mm across, though actual hole size can vary slightly depending on point geometry, material, runout, and drilling technique. Manufacturers typically produce metric bits in increments of 0.1 mm for small sizes and 0.5 mm or 1.0 mm for larger sizes, giving machinists and tradespeople a precise range to work with.
The most common metric drill bit sets cover 1 mm to 10 mm in 0.5 mm steps, or 1 mm to 13 mm in 0.5 mm steps. Specialty sets may include 0.1 mm increments from 1.0 mm to 5.0 mm for precision work, while reduced-shank sets extend to 13 mm, 16 mm, 20 mm, and beyond for larger holes in metal, wood, and plastic. The size printed on the shank or packaging is the nominal diameter, not the shank diameter.
How Metric Drill Bit Sizes Are Measured
The advertised size of a metric drill bit refers to the diameter across the cutting lips, measured at the outer corners. For a twist bit, that is the distance from one cutting edge to the opposite cutting edge. If the bit has a reduced shank, the shank may be smaller than the cutting diameter so it can fit into a standard chuck. Always check the cutting diameter when selecting a bit for a precise fit.
Metric sizes are usually expressed with one decimal place, such as 4.2 mm, 6.8 mm, or 10.2 mm. In high-precision applications, you may see two decimal places, like 3.05 mm or 5.55 mm. The tolerance on a drill bit can matter more than the nominal size. A cheap 5.0 mm bit may drill slightly oversize, while a high-quality bit held in a rigid setup may drill very close to its stated diameter.
Metric Versus Inch and Wire Gauge Drill Bits
Inch-based drill bits use fractional sizes, number sizes, and letter sizes. Fractional bits include 1/4 inch, 5/16 inch, and 3/8 inch. Number bits run from #80 to #1, while letter bits run from A to Z. Metric bits do not use those labels. A 6.35 mm bit is equivalent to 1/4 inch, a 7.94 mm bit is close to 5/16 inch, and a 9.53 mm bit is close to 3/8 inch. Those conversions are useful, but they are not always exact substitutes for true metric sizes.
When working with metric hardware, use true metric drill bits whenever possible. A 6.0 mm metric bolt does not align with a 1/4 inch bit, and a 10 mm hole is not the same as a 3/8 inch hole. Conversion charts help in a pinch, but a metric set avoids guessing. For critical fits, measure the fastener or consult the manufacturer's recommended hole size rather than relying on approximate inch-to-metric equivalents.
Choosing Metric Drill Bit Sizes for Specific Tasks
Selecting a metric drill bit size depends on what the hole is for. A hole that must accept a bolt freely has a different target diameter than a hole that will be tapped for threads or used as a pilot for a wood screw. Material also changes the equation. Aluminum, mild steel, stainless steel, hardwood, softwood, acrylic, and printed PLA or PETG all behave differently under a drill bit, so the same nominal size may produce different real-world results.
The three most common categories are tap drill sizes, clearance holes, and pilot holes. Tap drills prepare a hole for cutting internal threads. Clearance holes let a bolt or screw pass through without gripping. Pilot holes guide a screw or larger bit and prevent splitting or wandering. Once you understand the target diameter for each category, choosing from a metric drill index becomes straightforward.
Tap Drill Sizes for Metric Threads
For metric threads, the general tap drill formula is simple: tap drill diameter equals the nominal thread diameter minus the thread pitch. For an M6 x 1.0 thread, subtract 1.0 mm from 6.0 mm to get a 5.0 mm tap drill. For an M8 x 1.25 thread, subtract 1.25 mm from 8.0 mm to get 6.8 mm. For an M10 x 1.5 thread, subtract 1.5 mm from 10.0 mm to get 8.5 mm. This formula provides a starting point for standard coarse and fine metric threads.
Real-world tapping may call for a slightly different size depending on the material and the percentage of thread engagement desired. In hard materials, a slightly larger tap drill can reduce torque and breakage risk. In soft materials, a slightly smaller drill may provide stronger threads. Common metric tap drill sizes include 3.3 mm for M4 x 0.7, 4.2 mm for M5 x 0.8, 5.0 mm for M6 x 1.0, 6.8 mm for M8 x 1.25, and 8.5 mm for M10 x 1.5.
Clearance and Pilot Holes in Metric Sizes
Clearance holes are intentionally larger than the fastener diameter. For metric bolts, ISO 273 defines close, normal, and free fit clearance holes. A normal clearance hole for an M6 bolt is typically 6.6 mm, for an M8 bolt it is 9.0 mm, for an M10 bolt it is 11.0 mm, and for an M12 bolt it is 13.5 mm. Close fits use smaller diameters for alignment, while free fits use larger diameters to accommodate misalignment and easy assembly.
Pilot holes follow a different logic. For wood screws, the pilot hole diameter should roughly match the screw's root diameter, not its outer thread diameter. In softwoods, a slightly smaller pilot hole may be enough; in hardwoods, a larger pilot hole prevents splitting. Metric brad-point bits and dowel bits are often used for furniture and cabinetry because they create clean, accurate holes in 5 mm, 6 mm, 8 mm, and 10 mm sizes. Always test on scrap material when the fit is critical.
Building a reliable collection of metric drill bit sizes does not require every size ever made. Start with a 1 mm to 10 mm set in 0.5 mm increments, then add the tap drills, clearance sizes, and pilot bits that match the fasteners and materials you use most. A printed chart taped near the drill press and a few labeled index bottles can turn a confusing drawer of bits into a fast, accurate system. With the right metric sizes on hand, every hole becomes a repeatable step instead of a guess.