DeWalt DCST920 String Trimmer Line Replacement: Easy Step-by-Step Guide
The DeWalt DCST920 is a popular 20V MAX cordless string trimmer, and its bump-feed head makes quick work of edging and clearing grass. When the line runs out or snaps off repeatedly, a DeWalt DCST920 string trimmer line replacement is one of the easiest maintenance tasks you can do at home. You do not need a repair shop or special mechanical skills—just the right diameter line, a clean work area, and a few minutes of patience.
The DCST920 uses a dual-line bump feed system, so correct line size and winding direction matter more than many owners realize. Installing the wrong diameter or winding the spool backward can cause feeding problems, vibration, and unnecessary motor strain. This guide covers the exact line specification, compatible spool options, and a step-by-step process for replacing the line like a pro.
Understanding the DeWalt DCST920 Trimmer Head
The DCST920 is built around a bump-feed trimmer head that holds two separate lengths of line on a single spool. When you tap the bump knob against the ground while the trimmer is running, the head releases a small amount of line to maintain a fresh cutting edge. This design keeps you working without stopping to manually pull line every few minutes.
DeWalt specifies 0.080-inch diameter line for the DCST920, and the factory spool typically holds about 20 feet total. While aftermarket line can work, the head is calibrated for that diameter and a specific winding pattern. Using line that is too thick may bind inside the spool, while line that is too thin can break constantly or weld itself together under heat.
Line Size and Spool Compatibility
For reliable performance, stick with 0.080-inch replacement line. A pre-wound spool such as the DeWalt DWO1DT995 is a direct-fit option for many DCST920 trimmers, but you should always confirm compatibility with your trimmer's manual or serial number. Pre-wound spools eliminate the guesswork of winding and are ideal if you want the fastest possible swap.
If you prefer bulk line, buy a high-quality 0.080-inch round or twisted copolymer line. Avoid mixing diameters on the same spool, and never use metal wire or blade-like attachments. The DCST920's bump feed relies on smooth, flexible line that can slide through the eyelets and release evenly when tapped.
Tools and Materials You Will Need
Before you begin, gather safety glasses, work gloves, a clean rag, and a new pre-wound spool or a 20-foot length of 0.080-inch trimmer line. A flathead screwdriver and needle-nose pliers can help if old line is jammed, but most replacements only require your hands. Remove the battery from the trimmer before touching the head.
Work on a bench or driveway where you can turn the trimmer upside down and see the spool clearly. If you are reusing the original spool, inspect it for cracks, worn tabs, or melted plastic. A damaged spool will not feed line correctly, so replace it rather than trying to force it back into service.
Step-by-Step DeWalt DCST920 Line Replacement
The replacement process starts with safety and preparation. Remove the 20V MAX battery, turn the trimmer upside down, and wipe away grass clippings or dirt around the spindle. Debris that falls into the head can prevent the spool from rotating freely, which leads to feeding issues later.
From there, you will either drop in a pre-wound spool or wind fresh line onto the existing spool. Both methods require you to open the head, route the line through the eyelets, and secure the spool cap correctly. Take your time during the first few replacements, and the job will become second nature.
Removing the Old Spool and Line
Hold the trimmer head firmly with one hand. On the DCST920, locate the two release tabs on the sides of the spool cap. Press both tabs inward and pull the cap straight off; the bump knob is part of this cap, so do not try to unscrew it. Set the cap aside and lift the old spool out of the housing.
Remove any remaining line from the spool and clean the inside of the housing with a rag. Check the metal eyelets for sharp edges or deep grooves, because worn eyelets can fray new line immediately. Also inspect the spring beneath the spool and make sure it is not bent or missing before you install fresh line.
Winding and Installing New Line
If you are winding bulk line, cut two equal lengths of 0.080-inch line, roughly 10 feet each. Insert one end into the anchor hole on the spool and wind it tightly in the direction of the arrow molded into the plastic. Repeat for the second line on the other side of the spool, keeping the coils neat and avoiding crossed strands.
Thread each line through its matching eyelet in the housing, leaving about 5 to 6 inches extending beyond the head. Place the spool into the housing, align the spring, then press the spool cap back on until both tabs click into place. Reinstall the battery, tap the bump knob while the trimmer runs, and confirm that both lines advance evenly.
A few minutes of careful work now can save you from frustrating stalls later in the season. Keep a spare spool or a roll of 0.080-inch line in your garage, and check the trimmer head whenever you notice uneven cutting or short line. With the right supplies and the steps above, your DeWalt DCST920 will stay ready for clean edges, overgrown fence lines, and everything in between.