Ryobi String Trimmer Line Replacement: Fast, Easy Fix
Replacing the line in a Ryobi string trimmer is one of those small maintenance jobs that can make the difference between a clean, crisp lawn edge and a frustrating afternoon of stopping every few feet. Whether you own an 18V ONE+ trimmer, a 40V brushless model, or a gas-powered Ryobi unit, the cutting head eventually runs out of line or jams with debris. Knowing how to swap the line correctly saves money, reduces downtime, and keeps your trimmer performing like it should.
The good news is that Ryobi string trimmer line replacement does not require a repair shop. With the right diameter, a little patience, and an understanding of your specific cutting head, you can complete the job in minutes. This guide walks through compatibility, spool options, step-by-step replacement, and troubleshooting so your next line change goes smoothly.
Know Your Ryobi Trimmer Before Replacing the Line
Ryobi has produced dozens of string trimmer models over the years, and their cutting heads vary widely. Some use a simple bump-feed spool, while others rely on an auto-feed system, a Speed Load head, or a pre-wound cartridge. Before buying replacement line, identify the exact model and head style so you do not waste time with incompatible parts.
The model number is usually printed on a label near the motor housing or on the shaft. Once you have it, check the operator’s manual or Ryobi’s website for the recommended line diameter. Using the wrong size can cause feeding problems, increase breakage, or even damage the spool housing over time.
Find the Correct Line Diameter and Type
Most Ryobi string trimmers use line diameters between 0.065 inches and 0.095 inches. Light-duty electric models often call for 0.065-inch or 0.080-inch line, while larger gas and 40V trimmers may use 0.095-inch line for tougher weeds. The correct size is not a suggestion; it is a specification that affects how well the bump-feed mechanism advances the line.
Line type matters too. Round line is the standard choice for general trimming, twisted line offers quieter operation and less welding, and serrated or star-shaped line can cut through thicker vegetation. If you are unsure, start with the OEM Ryobi replacement line or a high-quality equivalent that matches the original diameter and shape.
Choose Between Bulk Line and Pre-Wound Spools
Bulk trimmer line is the economical route. You buy a roll in the correct diameter, cut a measured length, and wind it onto your existing spool. This option gives you plenty of material for multiple replacements and lets you experiment with different line shapes if your trimmer tolerates them.
Pre-wound spools cost more per change but save time and reduce the chance of winding mistakes. Ryobi offers pre-wound replacement spools for many popular models, and aftermarket versions are widely available. If you dislike wrestling with tangled line or you maintain several trimmers, keeping one or two pre-wound spools on hand can be a practical investment.
Step-by-Step Ryobi String Trimmer Line Replacement
Safety comes first when working on any power tool. Remove the battery from electric models, and disconnect the spark plug boot on gas trimmers. Wear gloves and eye protection, because old trimmer line can be dirty, sharp, and springy when released from the spool.
Work on a clean, flat surface with good lighting. A bench or driveway is ideal because small springs, caps, and retaining clips can disappear quickly in grass. Lay out your replacement line, a tape measure, and any tools your manual recommends, such as a flathead screwdriver or a small hex wrench.
Removing the Spool and Old Line
Turn the trimmer upside down so the cutting head is facing you. Depending on the model, you may need to press two tabs on the spool cap, twist the cap counterclockwise, or remove a retaining screw. Once the cap is off, pull the spool straight out of the housing. Take a quick photo before disassembly if you are unfamiliar with the head.
Discard the old line, but inspect the spool and housing for wear. Clean out grass clippings, dirt, and melted plastic with a brush or compressed air. Check the eyelets on the housing for grooves or sharp edges that could fray new line. If the spool is cracked or the spring is stretched, replace those parts before continuing.
Winding New Line and Reassembling the Head
Cut a length of line according to your manual, often between 10 and 20 feet for many Ryobi models. Insert one end through the anchor hole in the spool, then wind the line tightly in the direction indicated by the arrow on the spool. Do not cross the line over itself; neat, even layers help prevent tangling and feeding issues.
Once wound, leave about 6 to 8 inches of line free on each side if your model uses two strings. Thread the ends through the eyelets in the housing, then seat the spool into the head. Reinstall the cap or retaining screw, bump the head on the ground to advance the line, and trim the ends to equal length. Reconnect power, start the trimmer, and test the feed before tackling heavy weeds.
Troubleshooting and Maintenance After Replacement
Even a correctly installed line can act up if something is slightly off. A trimmer that will not advance line, makes a grinding noise, or throws line out of the head usually has a simple cause. Diagnosing the issue early prevents bigger problems and keeps your replacement work from feeling wasted.
Most Ryobi feed problems trace back to line diameter, winding direction, or a dirty spool. The bump-feed system depends on friction and centrifugal force, so any extra resistance can stop the line from advancing. A few checks will usually reveal the culprit.
Fixing Common Feed and Tangling Problems
If the line will not feed, first confirm that you used the correct diameter. Line that is too thick binds inside the spool, while line that is too thin may slip and weld together. Also verify that you wound the line in the correct direction; reversing it can make the bump mechanism tighten the line instead of releasing it.
Tangling often happens when the line is wound too loosely or when two lines are wound together without separating them. Remove the spool, unwind the problem section, and rewind it carefully. If the line keeps breaking at the eyelet, inspect the eyelet for sharp edges and replace the spool cap or housing if necessary.
Keeping Your Ryobi Trimmer Line in Top Shape
Store replacement line away from direct sunlight and extreme heat. UV exposure and high temperatures can make nylon line brittle before you even use it. Keeping line in a sealed bag or a cool garage cabinet helps it last longer and reduces frustrating mid-job breaks.
After each use, clean the cutting head and check the line length. Do not overfill the spool, because too much line can press against the housing and cause feeding resistance. When you notice the line wearing unevenly or the spool becoming difficult to turn, take a few minutes to service the head. That small habit extends the life of your trimmer and makes every Ryobi string trimmer line replacement easier.
A little preparation goes a long way toward keeping your Ryobi trimmer ready for the next edge, fence line, or overgrown corner. Keep the correct diameter and a spare spool on hand, follow your model’s winding directions, and your trimmer will reward you with reliable cutting season after season.