String Trimmer Fuel Line Replacement: The Ultimate Guide to Fix Your Weed Eater
There are few things more irritating in yard work than a string trimmer that refuses to start. You prime the bulb, pull the cord until your shoulder aches, and the engine either sputters once or stays completely silent. In many cases, the real culprit is not the carburetor, the spark plug, or the ignition coil — it is a cracked, hardened, or clogged string trimmer fuel line that is no longer delivering gasoline the way it should.
Fuel lines are tiny, inexpensive components, but they live in a brutal environment. They sit submerged in ethanol-blended gasoline, bake under direct sun, and flex every single time the primer bulb is pressed. That combination eventually causes rubber and plastic to stiffen, split, and crumble. Learning how these lines work, how to spot failure early, and how to replace them properly will save you money at the repair shop and keep your equipment cutting cleanly for years.
Understanding the String Trimmer Fuel Line System
A string trimmer fuel line is not a single hose but usually a small network of two or three tubes running between the fuel tank, the primer bulb, the carburetor, and sometimes a fuel filter. On a typical two-cycle trimmer, one line carries fuel from the tank to the carburetor, while a second return line sends excess fuel back into the tank. The primer bulb sits in the middle of that loop and creates suction that pulls fresh fuel through the system before you pull the starter cord.
Because the engine is a two-stroke design, the fuel is mixed with oil at a ratio that is usually 50:1 or 40:1. That oil does not harm the lines, but ethanol in modern pump gasoline absolutely does. Ethanol attracts moisture, and that moisture causes the rubber to swell, harden, and eventually crack. A fuel line that has turned stiff and dark is a line that is about to fail, often at the worst possible moment in the middle of a job.
How Fuel Travels Through the System
The journey starts inside the fuel tank, where a weighted filter sits at the end of the supply line. That filter keeps dust, grass clippings, and grit out of the carburetor. When you press the primer bulb, a one-way valve inside the bulb pushes air out of the carburetor and pulls fuel up through the filter and along the line. Once the bulb fills with liquid fuel instead of bubbles, the carburetor is primed and ready for ignition.
From there, the return line carries the leftover fuel and vapor back into the tank, which prevents the carburetor from flooding. If either line is pinched, cracked, or disconnected, the pressure loop breaks and the engine will not draw fuel at all. This is why a trimmer can have a perfectly good spark plug and still refuse to fire — the fuel simply never reaches the combustion chamber.
Signs That Your Fuel Line Needs Replacing
The earliest warning sign is usually a trimmer that starts fine when cold but dies after a few minutes of use, or one that only stays running when the choke is partially engaged. Another common symptom is a primer bulb that never fills with fuel no matter how many times you press it. If the bulb stays empty or only half full, air is almost certainly entering through a cracked line somewhere in the loop.
Physical inspection tells you the rest of the story. Squeeze the line between your fingers — fresh fuel line is soft and pliable, while failing line feels stiff, brittle, or slick. Look for dark discoloration, tiny hairline cracks near the tank grommet, or fuel weeping around the carburetor fittings. Once a line is stiff enough that it holds its shape when bent, replacement is no longer optional.
Choosing the Right Replacement Fuel Line
Not all fuel line is created equal, and grabbing the first roll you see at a hardware store can lead to a trimmer that runs lean, overheats, and scores its piston. Fuel line is sized by inside diameter and outside diameter, and the correct size depends on the fittings on your specific carburetor and tank grommet. Too small and fuel flow is restricted; too large and the line will not seal against the fittings, which lets air into the system.
Material matters just as much as size. Standard vinyl or Tygon line is cheap and works well with straight gasoline, but it hardens quickly when exposed to ethanol. Polyurethane line resists ethanol far better and stays flexible in cold weather, while fluorinated options such as Viton are the gold standard for high-ethanol fuel blends, though they cost noticeably more per foot.
Matching Line Size to Your Trimmer
Most handheld string trimmers use line in the range of 3/32 inch inside diameter by 3/16 inch outside diameter, which is roughly 2.4 mm by 4.8 mm. Larger professional units and some backpack models use 3 mm by 5 mm or even 4 mm by 7 mm line. The safest approach is to check your owner's manual or measure the old line with calipers before ordering anything.
When in doubt, buy a small assortment kit rather than a single size. Kits typically include several diameters and a few feet of each, which costs about the same as two individual rolls and covers almost every common trimmer on the market. Keep the leftovers in a sealed bag away from sunlight so they stay usable for the next repair.
| Trimmer Type | Typical Line Size (ID x OD) | Notes |
|---|---|---|
| Standard handheld (Echo, Ryobi, Homelite) | 3/32" x 3/16" | Most common size sold in kits |
| Mid-size homeowner (Stihl FS series) | 3 mm x 5 mm | Often sold in metric coils |
| Professional and backpack units | 4 mm x 7 mm | Higher flow for larger displacement engines |
Ethanol Fuel and Line Longevity
Ethanol is the single biggest killer of small-engine fuel lines. It absorbs water from the air, and that water separates inside the tank and lines, creating corrosive acids that attack rubber from the inside out. Even a trimmer that sits for months at a time will suffer, because the damage happens whether the engine runs or not.
You can dramatically extend the life of a new string trimmer fuel line by using ethanol-free gasoline when it is available, or by adding a fuel stabilizer designed specifically for ethanol blends. Running the carburetor dry before long-term storage also helps, since it removes standing fuel from the lines and the metering chamber.
Replacing a String Trimmer Fuel Line Step by Step
Replacing fuel line is one of the most approachable repairs you can do on a trimmer. The parts cost only a few dollars, the tools are minimal, and the whole job usually takes twenty to forty minutes. The most important thing is to work slowly and photograph the routing before you remove anything, because lines can twist around each other in ways that are hard to remember later.
Before you begin, drain the fuel tank into an approved container and set the trimmer on a clean workbench with good lighting. You will need needle-nose pliers, a small flathead screwdriver, sharp scissors or a utility knife, and replacement line. A shallow pan under the work area catches any drips and keeps gasoline off your bench.
Removing the Old Line
Start by pulling the fuel lines off the carburetor fittings and the primer bulb nipples. They are usually held on by friction alone, so a gentle twist with needle-nose pliers is enough to break them loose. Next, work the tank grommet free — this is the rubber plug where the lines pass through the top of the tank. Push it inward and fish it out through the filler opening, or pry it up carefully with a flathead screwdriver.
Once the grommet is out, note which hole the long supply line passes through and which one the short return line uses. The supply line normally reaches all the way to the bottom of the tank and connects to the filter, while the return line stops just inside the tank. Getting these reversed is a common mistake that causes the trimmer to run poorly or not at all.
Installing and Testing the New Line
Cut the new line longer than you think you need, then route it through the grommet using a small pick or a piece of stiff wire as a guide. Trim the ends at a slight angle so they slide onto the carburetor and bulb fittings easily. Reattach the fuel filter to the end of the supply line and drop it back into the tank, then seat the grommet firmly in the tank opening.
Add a small amount of fresh fuel mix and press the primer bulb several times. You should see fuel travel up the line and fill the bulb with liquid rather than bubbles. If the bulb stays empty, check that the lines are not swapped and that the grommet is fully seated. Once fuel flows correctly, start the engine and let it idle for a minute before heading back out to the yard.
Keeping a few feet of spare fuel line on the shelf and checking yours once a season is a small habit that pays off with a trimmer that fires on the first or second pull every spring. If your line already feels stiff or your primer bulb refuses to fill, treat yourself to a fresh set of tubing this weekend — your shoulders and your lawn will both thank you for it.