#10 drill bit

The Ultimate #10 Drill Bit Guide: Sizes, Uses, and Top Picks

By John Martin
AD

A #10 drill bit is one of those small shop details that causes big confusion. The label sounds simple, but “#10” can refer to a wire-gauge drill bit, a pilot hole for a #10 screw, or a clearance hole for small hardware. Grab the wrong one and you can strip threads, split wood, or ruin a precision fit. Understanding the actual size and best use takes only a few minutes and saves a lot of rework.

In most drill bit indexes, a #10 drill bit is a numbered wire-gauge bit with a diameter of 0.1935 inches, or about 4.92 millimeters. It sits between a 3/16-inch bit and a 13/64-inch bit, and it is often used when a project calls for a hole slightly larger than a #10 screw shank. That distinction matters because a #10 screw and a #10 drill bit are related by name only, not by identical dimensions.

Understanding the #10 Drill Bit Size

Numbered drill bits follow the wire-gauge system, where higher numbers generally mean smaller diameters. A #10 bit is not the tenth-largest bit in a typical set; it is simply one size in a long sequence that runs from tiny bits like #80 up to larger numbered sizes. For machinists, woodworkers, and DIYers, knowing the decimal size helps when a project plan uses gauge numbers instead of fractions.

AD
Milwaukee 48-89-2310 13/64 in. COBALT RED HELIX
Milwaukee 48-89-2310 13/64 in. COBALT RED HELIX
MILWAUKEE 48-89-2310 RED HELIX COBALT 13/64" DRILL BIT
MILWAUKEE 48-89-2310 RED HELIX COBALT 13/64" DRILL BIT
Alpen HSS Jobber Drill Bit 20mm Red Shank 12.5mm Reduced Size
Alpen HSS Jobber Drill Bit 20mm Red Shank 12.5mm Reduced Size

The #10 bit is a useful middle-range size. It is large enough to handle small bolts, screws, and hardware, but small enough for detailed work in metal, plastic, and wood. Because its diameter is close to 5 millimeters, it sometimes gets swapped with a 5 mm bit in casual work. That swap can be acceptable for a rough clearance hole, but it is a poor choice when tolerance or thread engagement matters.

What the “#10” Designation Actually Means

When a drill bit is labeled #10, that label refers to the wire-gauge size of the bit itself. It does not mean the bit is designed only for #10 screws. The numbered system originated in metalworking and is still used because it offers precise, repeatable sizes that do not always line up with common fractional or metric bits.

BOSTAL 21PCS Drill Bit Set
BOSTAL 21PCS Drill Bit Set
Milwaukee 5/16" JOBBER BIT THUNDER - pack of 3 48892726-XCP3
Milwaukee 5/16" JOBBER BIT THUNDER - pack of 3 48892726-XCP3
Alpen 10mm Cobalt Steel Drill Bit for Hard Metals - Titanium Finish
Alpen 10mm Cobalt Steel Drill Bit for Hard Metals - Titanium Finish

This is where many people get tripped up. A #10 screw has a major diameter of roughly 0.190 inches, while a #10 drill bit measures 0.1935 inches. The two numbers are close, which is exactly why a #10 bit can work as a close-clearance hole for a #10 screw. For a pilot hole, however, you normally need a smaller bit so the screw threads can bite into the material.

#10 Drill Bit Decimal and Metric Equivalents

In decimal inches, a #10 drill bit is 0.1935 inches. In metric terms, that converts to approximately 4.92 millimeters. The nearest common fractional size is 3/16 inch, which is 0.1875 inches, and the next common size up is 13/64 inch, which is 0.2031 inches. A 5 mm bit is 0.1969 inches, so it is slightly larger than a true #10.

AD

Those small differences add up in precision work. If you are drilling a clearance hole for a machine screw, a 5 mm bit may be fine. If you are creating a pilot hole, aligning a dowel, or working with hard metal, use the actual #10 size or the exact size specified by the hardware manufacturer. Measuring with calipers or checking a drill size chart removes the guesswork.

Alpen HSS Jobber Drill Bit 7.5mm for Steel - Durable & Fast
Alpen HSS Jobber Drill Bit 7.5mm for Steel - Durable & Fast
Jobber Length Drill Bit
Jobber Length Drill Bit
Irwin 5/8" HSS Drill Bits 1/2" Reduced Shank Silver & Deming
Irwin 5/8" HSS Drill Bits 1/2" Reduced Shank Silver & Deming
Alpen HSS Jobber Drill Bit 6.8mm Bulk for Steel Drilling
Alpen HSS Jobber Drill Bit 6.8mm Bulk for Steel Drilling
Alpen HSS Super Drill Bit 0.4mm for Precision Drilling - Bulk
Alpen HSS Super Drill Bit 0.4mm for Precision Drilling - Bulk
ALPEN HSS Jobber Drill Bit 9.0mm - Precision Steel Cutting Tool - 2 Pack
ALPEN HSS Jobber Drill Bit 9.0mm - Precision Steel Cutting Tool - 2 Pack

Using and Choosing a #10 Drill Bit

A #10 drill bit earns its place in a set because it covers several everyday tasks. It can open a clean passage for small hardware, enlarge an existing hole in small increments, or serve as part of a stepped drilling process. The key is matching the bit to the material and the job instead of assuming that one #10 bit works the same in every situation.

Bit material, coating, and point angle matter as much as diameter. A cheap bit may cut soft pine just fine, but it can dull quickly in stainless steel or hard hardwood. A well-made #10 bit with the right geometry will drill straighter, run cooler, and last longer, especially when you use the correct speed and feed.

AD

Pilot Holes, Clearance Holes, and #10 Screws

A #10 drill bit is often used as a clearance bit for #10 screws. Because the bit is slightly wider than the screw shank, the screw can pass through the top piece of material without biting into it. This is common in assemblies where the screw needs to pull two pieces together, such as attaching a bracket to a board or joining metal components with machine screws.

KMIZ Diamond Nail Bits DFL 2.3-10S (5Pack), Flame Cuticle Drill Bit, Pro Diamond Nail Bi
KMIZ Diamond Nail Bits DFL 2.3-10S (5Pack), Flame Cuticle Drill Bit, Pro Diamond Nail Bi
ad eBay | $53.99 | 29/32” Drill Bit Long National Twist Drill USA 10” 🇺🇸 Excellent | Home & Garden
ad eBay | $53.99 | 29/32” Drill Bit Long National Twist Drill USA 10” 🇺🇸 Excellent | Home & Garden
竹用ドリル|創業1923年 木工ドリルメーカーの株式会社スターエム
竹用ドリル|創業1923年 木工ドリルメーカーの株式会社スターエム

For actual pilot holes in wood, choose a smaller bit. A #10 wood screw typically needs a pilot hole somewhere between 3/32 inch and 1/8 inch, depending on whether the wood is soft or hard, the screw type, and whether you are drilling near an edge. For tapped holes in metal, standard tap drill sizes for #10 machine screws are also smaller than a #10 drill bit. Always check a tap drill chart before threading.

Materials, Coatings, and Drilling Technique

High-speed steel (HSS) is the standard choice for general-purpose #10 drill bits. It handles wood, plastic, aluminum, and mild steel well when used at the right speed. Cobalt bits resist heat and wear better in stainless steel and other hard metals, while carbide-tipped bits are intended for masonry and abrasive materials. Titanium nitride and black oxide coatings can improve lubricity and chip flow, but they do not turn a soft bit into a miracle worker.

AD

Point angle also changes performance. A 118-degree point is common for general drilling, while a 135-degree split point starts easier and is preferred for metal because it reduces walking. Brad-point bits are better for wood because they create cleaner entry holes. For a #10 bit in a home shop, a 135-degree split-point HSS bit is a versatile compromise for metal and hard plastic, while a brad-point version is worth having for cabinetry and trim. Use slower speeds and cutting fluid in metal, moderate speed in plastic to avoid melting, and a backer board in wood to reduce tear-out. Wear eye protection, clamp the workpiece, and keep the bit sharp so it cuts instead of rubbing.

Whether you are building a jig, mounting hardware, or sorting out an inherited drill index, knowing the real size of a #10 drill bit keeps your work precise. Check the decimal equivalent, match the bit to the material, and treat it as a clearance or general-purpose size rather than a universal pilot bit. Keep a sharp #10 on hand, label your storage clearly, and your next hole will be far less mysterious.

AD