#50 drill bit

The Ultimate #50 Drill Bit Guide: Sizes, Uses & Top Picks

By John Wilson
AD

A #50 drill bit is one of those small tools that rarely gets a second glance until a project demands genuine precision. Measuring exactly 0.0700 inches in diameter — roughly 1.78 millimeters — it belongs to the wire-gauge family of drill sizes, a numbering system that many hardware-store shoppers have never even heard of. Walk into a typical big-box store and you will find fractional bits in neat little sets, but a #50 lives in the specialty drawers, the machinist catalogs, and the well-organized bench of someone who does delicate work for a living.

What makes this particular size worth knowing about is its role as the standard tap drill for 2-56 machine screw threads, a thread size found in everything from electronic enclosures to model railroad chassis. Use a bit that is a hair too large and the threads come out weak and sloppy; use one that is slightly too small and you risk snapping a tap inside the hole — one of the most frustrating problems in small-scale fabrication. Understanding the #50 drill bit means understanding how wire-gauge sizing works, what materials it handles well, and how to keep such a slender piece of steel from breaking in the middle of a job.

What Size Is a #50 Drill Bit?

The #50 bit has a diameter of 0.0700 inches, which converts to 1.778 millimeters. That places it in the gap between the 1/16-inch bit (0.0625 inches) and the 5/64-inch bit (0.0781 inches), meaning no common fractional drill size matches it. This is precisely why the wire-gauge system exists: it fills in the increments that fractional sets skip over, giving machinists and hobbyists a much finer level of control when hole diameter actually matters.

AD
Diablo 1/2" x 37" x 39" SDS-Plus 2-Cutter Carbide-Tipped Hammer Drill Bit - DMAPL2350
Diablo 1/2" x 37" x 39" SDS-Plus 2-Cutter Carbide-Tipped Hammer Drill Bit - DMAPL2350
Irwin 5/8" HSS Drill Bits 1/2" Reduced Shank Silver & Deming
Irwin 5/8" HSS Drill Bits 1/2" Reduced Shank Silver & Deming
DEWALT DT4520-QZ Brad Point Drill Bit 20mm DEWDT4520QZ
DEWALT DT4520-QZ Brad Point Drill Bit 20mm DEWDT4520QZ

Because of that precision, the #50 is often sold individually or as part of a numbered 1-to-60 or 1-to-80 set rather than in a standard household bit kit. If you find yourself repeatedly reaching for this size, buying a complete number-drill index usually works out cheaper and far more convenient than ordering single bits one at a time.

How the Wire Gauge System Works

Wire-gauge drill bits are numbered from 1 through 80, and the numbering runs counterintuitively: the larger the number, the smaller the bit. A #1 bit measures 0.228 inches across, while a #80 bit is a hair-thin 0.0135 inches. The system traces back to the drawing dies used in wire manufacturing, where each successive pass through a die produced a thinner strand of wire, and drill makers simply adopted the same progression for their tooling.

Alpen HSS Jobber Drill Bit 20mm Red Shank 12.5mm Reduced Size
Alpen HSS Jobber Drill Bit 20mm Red Shank 12.5mm Reduced Size
Stepped Drill Bit
Stepped Drill Bit
How to Choose the Right Drill Bit
How to Choose the Right Drill Bit

The #50 sits comfortably in the middle-to-small end of that range. It is large enough to be handled and sharpened without a microscope, but small enough that it demands a delicate touch and a rigid setup. Bits in the 40s and 50s are the workhorses of small-parts machining, and the #50 in particular earns its keep because of one very specific threading job.

#50 vs Fractional and Metric Equivalents

If you are trying to substitute a #50 bit with something from a fractional or metric set, you will be making a compromise. The nearest metric size is 1.8 millimeters, which is about 0.022 millimeters larger — a difference that sounds trivial but can affect thread engagement when you are tapping. The nearest fractional sizes are 1/16 inch (smaller by 0.0075 inches) and 5/64 inch (larger by 0.0081 inches), and neither one is a sensible stand-in for tapping purposes.

AD

The table below shows how the #50 lines up against its immediate neighbors in the wire-gauge sequence, which helps illustrate just how narrow the usable margin really is at this scale.

Wickes Multipurpose Drill Bit - 6 x 100mm
Wickes Multipurpose Drill Bit - 6 x 100mm
an image of a drill bit on a white background
an image of a drill bit on a white background
Aircraft Extension Drill Bits | NAS 907, Long Reac
Aircraft Extension Drill Bits | NAS 907, Long Reac
COMOWARE Jobber Drill Bit Set Comprehensive Drill Bit Collection, Vonder Drill Bit Collection, Vonder Drill Bit Set, Vonder Top Drill Bit, 19-piece Drill Bit Collection, Godhand Drill Bit Set, Metal Drill Bits Collection, Vonder Brand Drill Bit, Professional Drill Bit Set B&q
COMOWARE Jobber Drill Bit Set Comprehensive Drill Bit Collection, Vonder Drill Bit Collection, Vonder Drill Bit Set, Vonder Top Drill Bit, 19-piece Drill Bit Collection, Godhand Drill Bit Set, Metal Drill Bits Collection, Vonder Brand Drill Bit, Professional Drill Bit Set B&q
Tricone drill bit
Tricone drill bit
BOSTAL 21PCS Drill Bit Set
BOSTAL 21PCS Drill Bit Set
Drill SizeDecimal InchMillimeterPosition Relative to #50
#480.07601.930Notably larger
#490.07301.854Slightly larger
#500.07001.778Reference size
#510.06701.702Slightly smaller
#520.06351.613Close to 1/16 inch

What a #50 Drill Bit Is Used For

The single most common application for a #50 bit is drilling the hole for a 2-56 tap. In that role it produces roughly a 75 percent thread engagement, which is the sweet spot for small fasteners: strong enough to hold torque, open enough that the tap does not fight its way through and snap. Anyone who has built instrument panels, radio-controlled models, telescope mounts, or electronic test equipment has almost certainly relied on this pairing without giving it much thought.

Beyond tapping, the #50 shows up whenever a small, accurately sized clearance or pilot hole is needed. It is a popular choice for running thin hookup wire through a chassis wall, opening up printed circuit board mounting holes for small standoffs, and creating pilot holes in hardwood before driving tiny brads or brass screws. In each case, the goal is the same: a clean, round hole that does not split the surrounding material or leave a fastener rattling around.

AD

Tapping and Threading Applications

For a 2-56 UNC thread, the #50 drill is the accepted standard, and you can generally rely on published tap drill charts to confirm it. The resulting hole leaves just enough material for the tap to cut clean, well-formed threads. Going up to a #49 often produces threads that feel loose or strip under light load, while stepping down to a #51 increases the risk that the tap binds, squeaks, and shears off in the hole.

Cobalt & Carbide Drills, Taps
Cobalt & Carbide Drills, Taps

Practical examples abound in small-scale repair work. Gunsmiths use 2-56 hardware for scope mounts and custom fittings. Model engineers tap 2-56 holes for truck bolsters and coupler pockets on miniature locomotives. Electronics technicians use these threads for rack rails and panel hardware. In all of these settings, the quality of the drilled hole determines the quality of the finished thread, and that starts with a sharp #50 bit turning at the right speed.

Electronics, Hobby, and Precision Assembly

In electronics work, a #50 bit is handy for enlarging plated-through holes that are too snug for a component lead, or for drilling fresh holes in unplated prototyping board. It is also useful for opening up plastic enclosures so that a small connector or grommet fits without cracking the wall. Because the bit is small, it removes material gradually, which reduces the chance of grabbing and splitting brittle ABS or polycarbonate.

AD

Hobbyists reach for this size constantly. Scale modelers drill it for rigging line and tiny structural pins. Jewelry makers use it for jump rings and rivet holes in thin sheet. Clock and watch repairers use bits in this range to open worn pivot holes before bushing. Even leatherworkers and bookbinders find a #50 handy when they need a finely controlled hole in a decorative panel.

Choosing and Using a #50 Bit Without Breaking It

Small drill bits break. That is the reality of working at this scale, and a #50 is thin enough that a moment of sideways pressure or a slightly misaligned setup will snap it clean off. The good news is that most breakage comes down to technique rather than bad luck, and a few simple habits will dramatically extend the life of your bits.

The first consideration is fit. Many #50 bits are sold as plain wire-gauge shanks measuring 0.070 inches, which means they will slip in a standard 3/8-inch drill chuck unless it closes down to nearly zero. For hand work, a pin vise or a small keyless micro chuck is the practical answer. If you plan to use a drill press, look for versions of the bit that are mounted in a 1/8-inch shank — these are widely available and far easier to control.

Bit Types and Materials

High-speed steel is the default material and handles aluminum, brass, plastics, and mild steel without complaint. Cobalt bits hold up better in harder or abrasive materials and resist heat a little more gracefully, at a higher price. Solid carbide bits stay sharp far longer in abrasive substrates like fiberglass-reinforced circuit board material, but they are brittle and will shatter rather than bend if you side-load them.

Length matters just as much as material. Jobber-length bits are the general-purpose option, but for a bit this thin, screw-machine length — sometimes called stub length — is the smarter choice. The shorter flute and overall length mean far less flex, which translates directly into fewer snapped bits and straighter holes. Coatings such as titanium nitride or black oxide offer modest improvements in wear resistance and chip clearance, though technique still counts for more than any surface treatment.

Speeds, Feeds, and Preventing Breakage

When drilling metal with a bit this small, spin it fast and feed it gently. On a drill press, run the spindle near its top speed — often 2,000 to 3,000 RPM — and apply light, steady pressure rather than forcing the cut. In deeper holes, back the bit out frequently to clear chips, since a packed flute is one of the leading causes of breakage. A drop of cutting fluid or even a little light oil makes a noticeable difference in aluminum and steel.

Watch for the warning signs. A high-pitched squeal usually means the bit is rubbing instead of cutting, which often points to a dull edge or too little feed pressure. Smoke or a gummy, melted hole in plastic means the speed is too high and the bit is generating heat. If the bit wanders off center on a curved or angled surface, start with a center punch mark or a small spot from a center drill. Take these cues seriously and a single #50 bit can last through dozens of holes instead of a handful.

Whether you are tapping a dozen 2-56 holes in a custom enclosure or simply trying to thread a wire through a tight chassis wall, the #50 drill bit earns its place in the toolbox through accuracy rather than brute force. Pick up a spare or two in both plain and 1/8-inch shank versions, keep them in a dedicated index so they do not get mixed in with the drill-point bits, and treat them as the precision instruments they are. Your next small project will go smoother because of it.

AD