7/8 drill bit

7/8 Drill Bit: The Ultimate Guide to Sizes, Types, and Uses

By Brian Lee
AD

A 7/8 drill bit bores a hole that measures exactly 0.875 inches across, which translates to 22.225 millimeters. That makes it one of the most requested sizes in electrical work, metal fabrication, and heavy woodworking, yet it rarely gets the attention that popular sizes like 1/4 or 1/2 receive. If you have ever wired a subpanel, mounted a conduit fitting, or tapped a one-inch threaded hole, there is a good chance a 7/8 bit did the heavy lifting.

Not every 7/8 bit is built the same, and choosing the wrong one costs you time, money, and a lot of burned metal. A twist bit for mild steel behaves nothing like a spade bit for pine, and a reduced-shank bit designed for a hand drill will not fit an SDS rotary hammer. This guide breaks down the size standards, the materials each bit type handles best, and the cutting speeds that keep your edges sharp and your holes round.

Understanding the 7/8 Drill Bit and Its Place in the Size Chart

Fractional inch drill bits are named by the diameter of the hole they produce, and 7/8 is one of the standard steps in that lineup. It falls between 13/16 and 15/16, sitting comfortably in the range where bits get large enough to demand serious torque but small enough to still run in a handheld drill with the right technique. Hardware stores stock it because electricians, plumbers, and fabricators all reach for it regularly.

AD
TCT Drill Bits Tungsten Carbide Tip Precision Ground Hardplate Locksmith Bit
TCT Drill Bits Tungsten Carbide Tip Precision Ground Hardplate Locksmith Bit
Milwaukee 7/8 in. X 4 in. X 6 in. Carbide Hammer Drill Bit for Concrete, Stone and Masonry Drilling
Milwaukee 7/8 in. X 4 in. X 6 in. Carbide Hammer Drill Bit for Concrete, Stone and Masonry Drilling
Zipper Zi-Bha1500Dn Sds Hammer Drill 3 In 1 - Drill Hammer + Chisel 1500W 240V
Zipper Zi-Bha1500Dn Sds Hammer Drill 3 In 1 - Drill Hammer + Chisel 1500W 240V

The size also matters because it is not a number drill, a letter drill, or an arbitrary metric size. It belongs to the fractional series, which means you can find it in nearly every drill index and every industrial supply catalog. That consistency makes it easy to replace, easy to specify on a drawing, and easy to match with the hardware it is meant to fit.

Decimal, Metric, and Fractional Equivalents Explained

In decimal inches, a 7/8 hole measures 0.875 exactly, which is 22.225 mm. The closest common metric drill is 22 mm at 0.8661 inches, and it is roughly 0.009 inches smaller than a true 7/8 hole. That difference sounds trivial, but on a tight-tolerance assembly it can mean a fitting that will not seat or a bolt that refuses to slide through without persuasion.

Stepped Drill Bit
Stepped Drill Bit
Pieces Tungsten Carbide Masonry Drill Bits, Multi-Material Triangle Metal Drill Bits for Tile, Concrete, Brick, Glass, Plastic, Marble, Mirror, Wood, Diamond (3/4/5/6/8/10/12mm)
Pieces Tungsten Carbide Masonry Drill Bits, Multi-Material Triangle Metal Drill Bits for Tile, Concrete, Brick, Glass, Plastic, Marble, Mirror, Wood, Diamond (3/4/5/6/8/10/12mm)
Square Drill Bit Set for Woodworking, Wear-Resistant HSS 1/4in 5/16in 3/8in 1/2in Milling Bit, Ideal Mortising Machine Attachment, Double Acting for the
Square Drill Bit Set for Woodworking, Wear-Resistant HSS 1/4in 5/16in 3/8in 1/2in Milling Bit, Ideal Mortising Machine Attachment, Double Acting for the

The table below shows how 7/8 compares to the neighboring sizes you are most likely to confuse it with, along with the jobs each one typically handles.

SizeDecimal (in)Metric (mm)Typical Application
13/160.812520.64Clearance for 3/4 inch bolts in structural steel
7/80.87522.2251/2 inch trade-size conduit knockouts, 1-8 tap drill
22 mm0.866122.0Metric hardware and European fixture mounts
15/160.937523.81Pass-through holes for 1/2 inch rigid pipe and cable

Where a 7/8 Inch Hole Is Actually Required

Electrical work is the biggest consumer of this size. Standard 1/2 inch trade-size conduit fittings, including compression connectors and rigid couplings, are designed to seat in a 7/8 inch knockout. Electricians cut those holes with twist bits, step bits, or knockout punches, and the 7/8 dimension shows up constantly in panel and junction box specifications.

AD

Machinists use 7/8 as the tap drill for a 1-8 unified coarse thread, which is the standard tap drill diameter recommended for that pitch. Woodworkers rely on it for dowel stock, large table legs, and cable runs through framing, while fabricators use it to open holes before boring them out to a finished size with a boring head or reamer. Plumbers also pass 1/2 inch black iron and copper lines through 7/8 holes where a snug but movable fit is wanted.

Irwin 9/64" x 2-7/8" Black Oxide HSS 135 Degree Drill Bit (63509)
Irwin 9/64" x 2-7/8" Black Oxide HSS 135 Degree Drill Bit (63509)
ROKTOR TCT Straight Shank Masonry Drill Bit 7.0 mm x 100mm in Silver
ROKTOR TCT Straight Shank Masonry Drill Bit 7.0 mm x 100mm in Silver
Dormer DORA1001100 HSS Jobber Drill Bit 11.00mm
Dormer DORA1001100 HSS Jobber Drill Bit 11.00mm
Vaunt SDS+ Drill Bit Value Pack - Set of 28
Vaunt SDS+ Drill Bit Value Pack - Set of 28
the different types of drill heads are shown in this image, including one with an open end
the different types of drill heads are shown in this image, including one with an open end
Starrett KDHSPO70 HSS Split Point Drill Bit 7.0 x 109mm STRKDHSPO70
Starrett KDHSPO70 HSS Split Point Drill Bit 7.0 x 109mm STRKDHSPO70

Choosing the Right 7/8 Drill Bit for Your Material and Tool

Bit selection starts with two questions: what am I drilling, and what am I drilling it with. A 7/8 bit designed for stainless steel will cut through a pine stud, but a 7/8 auger bit will destroy itself against a steel plate. The substrate decides the cutting geometry and the tool interface decides the shank.

Most drill chucks top out at 1/2 inch capacity, which creates an obvious problem when the bit itself is 7/8 inch wide. Manufacturers solve this with reduced-shank designs that pair a 7/8 inch cutting head with a 1/2 inch or 3/8 inch shank, letting a standard hand drill or drill press accept the bit without an adapter.

AD

High-Speed Steel, Cobalt, and Coated Twist Bits

High-speed steel is the baseline for metal drilling, and it handles mild steel, aluminum, and brass without complaint as long as you keep the speed reasonable and the chips clear. Black oxide coating offers modest heat resistance and better chip flow, while titanium nitride adds surface hardness that extends life in repetitive production work. Cobalt bits, typically M35 or M42, hold an edge at higher temperatures and are the right choice for stainless steel, hardened alloys, and any job where work hardening is a concern.

Drill Bit Set – 246 Piece Set
Drill Bit Set – 246 Piece Set

Point geometry is the detail most buyers overlook. A 118 degree point is the general-purpose standard, but a 135 degree split point starts cutting immediately without wandering, which matters a lot on a 7/8 bit that wants to walk across a smooth surface. Three-flat shanks prevent the bit from spinning in the chuck under the heavy torque a large diameter demands, and reduced-shank bits with a 1/2 inch shank are the practical choice for anything driven by a handheld drill.

Wood, Masonry, and Specialty 7/8 Options

For lumber, an auger bit is the fastest way to remove material because the screw tip pulls the bit through and the deep flutes clear chips efficiently. Spade bits are cheaper and fine for rough framing work, though they tend to tear the exit side of the hole. Forstner bits produce a flat-bottomed, clean-edged 7/8 hole and are the standard for cabinetry, dowel joinery, and any cut where appearance counts. Brad point bits offer a compromise for precision work in hardwood.

AD

Masonry calls for carbide-tipped bits in SDS Plus or SDS Max shanks, and rotary hammers rather than standard drills. Hole saws and carbide hole cutters provide an alternative when you need a 7/8 opening through sheet metal, plastic, or thin panels, and knockout punches are the professional route for electrical enclosures where deformation is unacceptable. Step bits that reach 7/8 give you flexibility when you are not sure what size you need until you get there.

Speeds, Feeds, and Techniques for a Clean 7/8 Inch Hole

Large bits fail for one reason more than any other: too much speed. A 7/8 bit has a much higher surface speed at the cutting edge than a small bit spinning at the same RPM, and that extra speed converts directly into heat. Heat dulls the edge, dull edges create friction, and friction creates more heat until the bit is ruined and the hole is work hardened.

The fix is straightforward. Slow the spindle down, apply steady feed pressure, and let the flutes do their job. A drill press makes this easy because you can lock the speed and control the feed, but a handheld drill works fine if you are disciplined about trigger control and keep the bit perpendicular to the surface.

Calculating the Right RPM for a 7/8 Bit

The standard formula is RPM equals surface feet per minute times 3.82 divided by the diameter in inches. With a 0.875 inch diameter, that works out to roughly 4.37 times the surface speed. Mild steel runs best between 90 and 110 surface feet per minute, which puts you in the 390 to 480 RPM range. Stainless steel at 30 to 50 surface feet per minute drops you to about 130 to 220 RPM, which is slower than most people instinctively drill.

The table below gives practical starting points. Reduce speed further if you hear chatter or see discolored chips, and remember that these numbers assume high-speed steel tooling with proper lubrication.

MaterialSurface Speed (SFM)Approximate RPM at 7/8 inch
Mild steel90 to 110390 to 480
Stainless steel 30430 to 50130 to 220
Aluminum250 to 3501,100 to 1,500
Brass and bronze150 to 200650 to 870
Hardwood (auger bit)Not applicable400 to 800 with slow feed

Lubrication, Pilot Holes, and Preventing Bit Burnout

Cutting fluid is not optional on metal. A dedicated tapping or drilling fluid pulls heat out of the cut and lubricates the edge, and on a 7/8 hole it can easily double the life of the bit. For aluminum, kerosene or a light lubricant works well. For stainless, a sulfurized or chlorinated cutting oil is worth the small investment. Wood needs no lubricant, but clearing chips frequently keeps the bit from binding.

Pilot holes are strongly recommended for any 7/8 cut. Start with a small bit, often 1/8 to 1/4 inch, to establish location and relieve the center of the larger bit. On thick metal, step up through intermediate sizes rather than jumping straight to 7/8, which reduces the load on the drill and prevents edge chipping. Clamp your workpiece, keep the bit straight, and back it out periodically to clear chips. When you finish, deburr the hole with a countersink or deburring tool and check the diameter with a caliper if the fit is critical.

Buying a 7/8 bit used to mean a trip to the hardware store and a guess about which flavor would survive your project. Today you can order cobalt split-point, reduced-shank, auger, or SDS variants with a few clicks, which makes it easier than ever to match the tool to the task. Take a minute to confirm the shank size of your drill, note the material you are cutting, and jot down the recommended RPM before you start. A bit that runs cool, feeds steadily, and leaves a clean edge pays for itself on the very first hole, and the next five hundred after that.

AD