What Is Romex Wire? A Simple Guide to NM Electrical Cable
If you have ever peeked behind a wall during a renovation or sorted through a box of electrical supplies, you have probably seen a flat, plastic-sheathed cable with the word "Romex" printed on it. In North American residential construction, Romex wire is one of the most common ways to bring power to outlets, switches, lights, and appliances. The term is used so often that many people treat it as a generic name for any non-metallic sheathed electrical cable, but there is more to this product than a familiar brand name.
Understanding what Romex wire actually is helps you identify it, choose the right size for a circuit, and recognize where it can and cannot be installed. This guide covers its construction, common types and gauges, code restrictions, and practical safety considerations. Whether you are planning a small DIY repair or simply want to speak the same language as your electrician, the details below will give you a solid foundation.
What Exactly Is Romex Wire?
Romex is a trade name owned by Southwire and is widely used to describe Type NM-B cable, which stands for non-metallic sheathed cable. It is not a single wire; it is a factory-assembled cable containing two or more insulated conductors plus a bare copper grounding conductor, all wrapped in a flexible plastic outer jacket. That jacket is typically made of PVC and is designed to protect the inner wires from abrasion and physical damage in dry, protected locations.
The "non-metallic" part is important because it separates Romex from cables that use a metal jacket, such as armored cable or metal-clad cable. Because it is lightweight, flexible, and relatively inexpensive, Romex became the standard wiring method for one- and two-family homes. It is commonly run through studs, joists, and ceiling cavities, connecting the electrical panel to the rest of the house.
Key Components of a Romex Cable
Inside a typical Romex cable, you will find individually insulated conductors. In a standard 12/2 NM-B cable, for example, there is a black insulated hot conductor, a white insulated neutral conductor, and a bare copper equipment ground. The black and white wires are covered with thermoplastic insulation, while the bare ground runs alongside them. The outer sheath holds everything together and provides a degree of mechanical protection.
The jacket is also printed with critical information: the manufacturer, the wire gauge, the number of conductors, the cable type, the voltage rating, and the temperature rating. For instance, "12/2 NM-B 600V" tells you the cable has two insulated 12-gauge conductors plus a ground and is rated for 600 volts. In NM-B, the individual conductors are rated for 90°C, but the overall cable ampacity is generally limited to the 60°C column of the National Electrical Code. That distinction matters when sizing circuits.
Romex vs. Other Electrical Cables
Romex is often compared with BX, which is an older term for armored cable, and MC, or metal-clad cable. Both BX and MC have a metallic outer covering that offers better protection against physical damage and can serve as part of the grounding path in some designs. Romex relies on the bare copper conductor for grounding and its plastic sheath for abrasion resistance, so it is best suited to dry, concealed spaces where it will not be stepped on or repeatedly disturbed.
Another cousin is UF-B, or underground feeder cable. UF-B looks similar to Romex but is designed for wet and damp locations, including direct burial. You might also see SE-R cable for service entrances or THHN wire pulled through conduit. Each product has a specific role. Romex is not a universal replacement for all of them, and using the wrong cable type in a wet or exposed location can create a serious code violation and safety hazard.
Common Romex Sizes, Types, and Applications
Romex comes in several gauge sizes and conductor counts, and the label tells you both. The first number is the American Wire Gauge, or AWG, of the conductors. The second number is the count of insulated conductors, not including the bare ground. So 14/2 has two insulated 14-gauge wires plus a ground, while 14/3 has three insulated 14-gauge wires plus a ground. The gauge determines how much current the cable can safely carry.
For residential branch circuits, the most common sizes are 14 AWG, 12 AWG, and 10 AWG. Larger sizes such as 8 AWG and 6 AWG are used for higher-demand appliances, subpanels, and service equipment. While sheath colors often follow a manufacturer convention, the printing on the jacket is the reliable way to identify the cable. Never assume gauge from color alone, especially in older homes where the color coding may not match modern standards.
NM-B, UF-B, and Other Variations
NM-B is the standard indoor Romex cable. The "B" indicates a 90°C insulation rating, which replaced older NM cable that had a lower temperature rating. NM-B is intended for dry, protected locations: inside walls, ceilings, and floors. It should not be installed in wet or damp areas, embedded in concrete, or exposed to direct sunlight unless specifically listed and marked for sunlight resistance.
UF-B is the underground feeder version. It has a solid plastic core and a gray jacket, and it can be direct buried or used in wet locations. Some people still call it Romex, but it is a different product with different code allowances. Other variations include NMC, which is corrosion-resistant, and NMS, which may include a signaling or communications conductor. For most homes, however, NM-B is the cable you will find behind the drywall.
Typical Residential Uses for Romex
Romex is used for nearly every branch circuit in a modern home. A 14/2 cable on a 15-amp breaker typically feeds bedroom outlets, lighting circuits, and smoke detectors. A 12/2 cable on a 20-amp breaker is common for kitchen countertop receptacles, bathroom circuits, laundry rooms, and garage outlets. A 10/2 cable on a 30-amp breaker may supply a water heater, while 10/3 is often used for an electric dryer.
For larger loads, 6/3 cable might feed a 50-amp electric range or a subpanel, depending on the distance and calculated load. The cable runs through drilled holes in framing, across attics, and behind finished walls. It is stapled within 12 inches of boxes and at intervals no greater than 4.5 feet, and it must be protected by nail plates where it passes close to the edge of a stud or joist.
Installation, Safety, and Code Considerations
Installing Romex is not difficult in theory, but it is governed by detailed electrical codes that vary by jurisdiction. The National Electrical Code provides the baseline, and local amendments can be stricter. Many areas require a permit and inspection for new circuits, and some require a licensed electrician for any work beyond simple replacements. Before you cut into a wall, confirm what your local building department expects.
Safety is the other half of the equation. Romex is safe when it is correctly sized, properly supported, and protected from damage. It becomes dangerous when it is overloaded, nicked during stripping, installed in wet locations, or connected to the wrong breaker. Always turn off power at the panel, verify that the circuit is dead with a reliable tester, and work methodically. If you are unsure about any step, stopping and calling a professional is far cheaper than an electrical fire.
Ampacity, Breakers, and Circuit Sizing
Ampacity is the maximum current a conductor can carry continuously without exceeding its temperature rating. In residential wiring, the standard matches are straightforward: 14-gauge copper on a 15-amp breaker, 12-gauge on a 20-amp breaker, 10-gauge on a 30-amp breaker, 8-gauge on a 40-amp breaker, and 6-gauge on a 50- or 60-amp breaker. These pairings assume typical conditions and copper conductors. Aluminum or long runs may require different sizing.
Never protect a 14-gauge circuit with a 20-amp breaker just because the wire fits the terminal. The breaker exists to protect the wire, not the appliance. If the wire overheats inside the wall, the breaker may not trip before the insulation is damaged. Voltage drop is another consideration on long runs, such as a detached garage or a distant well pump. In those cases, upsizing the wire can be necessary even if the amperage seems low.
Common Mistakes and Code Restrictions
One of the most common mistakes is using NM-B cable outdoors or underground. The plastic jacket is not designed for continuous moisture exposure, and the cable can degrade or allow water to reach the conductors. Another mistake is running Romex exposed in an area where it is subject to physical damage, such as across the face of basement joists or along a garage wall. Code generally requires protection in those spots, often with conduit, guard strips, or running boards.
Other frequent problems include missing staples, overfilled electrical boxes, damaged insulation from aggressive stripping, and ground wires that are cut too short or left disconnected. In attics, cable near an access opening may need added protection. In basements, exposed cable may need to run through bored holes or behind protective boards. Local inspectors see these issues constantly, and correcting them after the drywall is up is far more expensive than doing the installation correctly the first time.
How to Identify and Work With Romex Safely
If you open a wall and see a flat cable with a white, yellow, orange, black, or gray jacket, there is a good chance it is Romex. Look for printing along the sheath. You should see the gauge, conductor count, "NM-B," a voltage rating, and a listing mark. That printing is your best guide to what the cable can handle and where it is allowed to be installed.
Working with Romex requires only a few basic tools: a tape measure, drill, wire strippers, cable ripper, staples, a hammer, and voltage tester. The skill lies in doing the small things correctly: leaving enough wire at boxes, maintaining gentle bends, keeping the cable flat, and tightening terminations to the proper torque. Those details determine whether the installation is reliable decades from now.
Reading the Label and Color Codes
A label such as "14/2 NM-B 600V" means the cable contains two insulated 14-gauge conductors plus a bare ground. "12/3 NM-B" means three insulated 12-gauge conductors plus a ground, which is useful for switched outlet circuits, three-way switches, or multi-wire branch circuits. The sheath color may be white for 14-gauge, yellow for 12-gauge, and orange for 10-gauge in many modern cables, but color is a convenience, not a code requirement.
Older cables may be all white or have faded printing, so never trust color alone. If the jacket is illegible, turn off the circuit and use a wire gauge or consult a qualified electrician. Knowing the exact cable type matters because replacing a 14-gauge circuit with a 12-gauge cable does not automatically mean you can install a 20-amp breaker; the entire circuit, including receptacles and switches, must be rated for the higher amperage.
Best Practices for Cutting, Stripping, and Terminating
When preparing Romex, cut the cable squarely and strip the outer jacket carefully. Use a cable ripper or utility knife with a shallow score, then peel the sheath back without nicking the copper. At least 6 inches of free conductor should be available inside each box for making splices or connecting devices. The bare ground should be long enough to reach the grounding screw or splice point comfortably.
Secure the cable with staples that are wide enough to hold the jacket without crushing it. Keep the cable flat and avoid sharp bends; the bend radius should not be less than five times the cable diameter. Use listed connectors where the cable enters a box, and make sure the box is large enough for the number of conductors and devices it contains. After terminating, give each connection a gentle tug, close the box, and test the circuit before restoring power.
Whether you are mapping circuits in an older home, planning a remodel, or simply trying to understand the wiring behind your walls, knowing what Romex wire is gives you a practical advantage. Check the jacket printing, respect local code, and match the cable to the load rather than the other way around. When a job feels over your head, bring in a licensed electrician. The right cable in the right place is what keeps a modern home running quietly and safely for years.