10/3 UF Wire: The Ultimate Guide to Underground Electrical Cable
10/3 UF wire is a heavy-duty underground feeder cable designed for direct burial and wet locations. The label 10/3 tells you it has three 10-gauge insulated conductors plus a ground. It is commonly sold as 10/3 UF-B cable, and it is a workhorse for outdoor circuits that need a neutral, such as a 30-amp subpanel, a well pump, or a detached garage feed.
Choosing the right underground wire is not just about gauge. It is about insulation type, burial depth, ampacity, voltage drop, and code compliance. A 10/3 UF cable can simplify a project because it can be buried without conduit in many cases, but it is not the right choice for every load. Understanding its limits helps you avoid nuisance breaker trips, failed inspections, and dangerous overheating.
What Is 10/3 UF Wire and What Does the Label Mean?
UF stands for Underground Feeder. In the electrical trade, UF cable is a factory assembly of insulated conductors with an overall moisture-resistant jacket. The "10/3" designation means the copper conductors are 10 AWG, and there are three insulated conductors. Those are typically black, red, and white. A bare or green equipment grounding conductor is also included, but it is not counted in the "3." The "B" in UF-B indicates a second-generation design with improved sunlight and moisture resistance.
Because it is built for harsh environments, 10/3 UF wire can be installed in direct burial applications, inside conduit, and in wet or damp locations. It is rated 600 volts and is commonly used for 120/240-volt systems. The outer jacket is tough, but it is not armor. It still needs proper bedding, protection from sharp rocks, and compliance with local burial depth rules.
Decoding 10/3: Gauge, Conductors, and Ground
The "10" is the American Wire Gauge, or AWG. A lower AWG number means a thicker conductor. 10 AWG copper is significantly thicker than 12 AWG, which is why it can handle more current. The "3" means three insulated conductors: one black hot, one red hot, and one white neutral. The ground is separate. This is different from 10/2 UF wire, which has only two insulated conductors: black and white, plus ground. If your project needs both 240 volts and 120 volts, 10/3 is often the minimum cable because it provides a neutral.
For example, a 240-volt subpanel in a detached garage usually needs two hots, a neutral, and a ground. A 10/3 UF-B cable gives you all four conductors. A 10/2 cable would provide only one hot, one neutral, and ground, which is fine for a simple 240-volt load without 120-volt components. That extra red conductor in 10/3 is what allows split-phase power and separate 120-volt circuits.
UF-B vs. NM-B vs. THHN in Conduit
NM-B, often called Romex, is the standard cable for dry indoor locations. It cannot be buried directly and should not be used in wet areas. UF-B is the outdoor and underground cousin. It has a solid or stranded copper core, thicker insulation, and a jacket that resists moisture, sunlight, and soil contact. THHN is a single conductor that must be installed inside conduit. It is often used for underground runs because it pulls more easily and may allow a smaller conduit size.
So when should you choose 10/3 UF wire? Choose it when you want a direct-burial cable that can be run without conduit, or when local code allows it in a short conduit sleeve for protection. Choose individual THHN/THWN wires when the run is long, the conduit path is complex, or you need maximum ampacity and easier pulling. In many residential projects, 10/3 UF-B is the practical middle ground: tough enough for the trench, flexible enough to route around obstacles, and ready for wet locations.
Ampacity, Voltage Drop, and Sizing 10/3 UF Wire
Ampacity is the maximum current a wire can carry safely. For 10 AWG copper UF cable, the allowable ampacity is generally 30 amps at 60°C. That means a 10/3 UF wire can be protected by a 30-amp breaker, provided the load does not exceed the circuit rating and voltage drop is acceptable. However, ampacity is not the only number that matters. Continuous loads, ambient temperature, bundling, and termination ratings can all reduce the usable capacity.
Voltage drop becomes a major factor on underground runs because trenches are long. A cable that works perfectly at 20 feet may perform poorly at 150 feet. Too much voltage drop can cause motors to overheat, lights to dim, and equipment to malfunction. Before buying 10/3 UF wire, estimate the one-way distance from the power source to the load and compare it with the load's amperage and voltage.
Ampacity and Breaker Sizing for 10/3 UF
A 10/3 UF-B copper cable is typically installed on a 30-amp breaker for 240-volt circuits. At 240 volts, that provides up to 7,200 watts of capacity. For continuous loads, such as a pump running for three hours or more, the load should not exceed 80% of the breaker rating, which is 24 amps. That leaves a safety margin for start-up surges and future additions. If the load is a motor, check the nameplate for full-load amps and locked-rotor amps. Motors often require a breaker sized for starting current while the wire must still handle the running load.
Termination temperature also matters. Even if the cable itself has a higher insulation rating, the lugs on breakers, receptacles, and panels may be rated for 60°C or 75°C. In residential panels, 60°C is common for small branch circuits. That keeps the practical limit at 30 amps for 10 AWG copper. If you bundle multiple current-carrying conductors in a conduit or run them through a hot attic, apply derating factors. When in doubt, consult the NEC ampacity tables and your local inspector.
Voltage Drop on Long Underground Runs
Voltage drop is the loss of voltage as current travels through resistance. For single-phase circuits, the approximate formula is: voltage drop = 2 × K × I × L ÷ circular mils, where K is about 12.9 for copper, I is current in amps, and L is one-way length in feet. For 10 AWG copper, the circular mil area is 10,380. Using that math, a 30-amp load at 240 volts will drop about 7.5 volts over 100 feet. That is roughly 3.1%, which is right at the recommended maximum of 3% for a branch circuit.
At 120 volts, the same 100-foot run with a 20-amp load can drop about 5 volts, or over 4%. That is why long 120-volt runs often need a larger gauge. If your run is longer than 100 feet, or if the load is sensitive to low voltage, consider upsizing to 8/3 UF or 6/3 UF. The extra cost is minor compared with the labor of trenching twice. A qualified electrician can run a voltage drop calculation based on your exact load and distance.
Installation and Common Applications
Installing 10/3 UF wire is straightforward, but the details determine whether the job passes inspection. The cable should be unrolled carefully to avoid kinks and nicks. The trench should be free of sharp rocks, glass, and debris. A layer of sand or fine soil beneath and above the cable protects the jacket. If the cable enters a building, it must be protected from physical damage, often with a conduit sleeve and a proper connector.
Common applications include detached garages, workshops, sheds, well pumps, outdoor lighting, and small subpanels. The cable is also used for 240-volt equipment that needs a neutral, such as some dryers, ranges, and HVAC systems when installed in a wet or underground location. Always match the wire to the load, the overcurrent device, and the code requirements for the specific installation.
Direct Burial and Conduit Installation
The NEC generally requires a minimum burial depth of 24 inches for direct-buried UF cable. There are exceptions: a residential branch circuit rated 120 volts or less and protected by a GFCI may be buried at 12 inches, and cable installed in PVC conduit may require 18 inches of cover. These depths can vary by local amendment, so check with your building department before digging. The trench should be straight and free of sharp objects. Warning tape or a tracer wire above the cable can help prevent future excavation damage.
UF cable can be installed in conduit, but it is not always easy to pull because of its thick jacket. If you use conduit, size it according to conduit fill rules and use long sweeps to reduce friction. Do not use UF cable where it will be subject to excessive flexing or physical abuse. Where the cable emerges from the ground, protect it with a rigid sleeve or conduit up to at least 8 feet above grade if it is exposed to damage. Seal the conduit ends to keep water and pests out, and use listed connectors.
Typical Uses for 10/3 UF Wire
A 10/3 UF wire is an excellent choice for a 30-amp feeder to a detached garage, workshop, or pump house. It can supply a small subpanel with 240 volts and 120 volts, allowing lights, receptacles, and a small welder or compressor. It is also common for deep-well pump systems where the pump control box needs a neutral. For outdoor outlets, a 10/3 cable can be used for a multiwire branch circuit, providing two 120-volt circuits with a shared neutral, but GFCI protection is required.
Other uses include feeding a 240-volt air conditioner, a greenhouse heater, or a dock circuit when protected by the correct breakers and GFCI devices. It is not the right cable for a 50-amp hot tub, a large EV charger, or a whole-house feed. Those loads need larger conductors, such as 6/3 or 4/3 UF, or individual THHN wires in conduit. The key is to calculate the load first, then choose the cable. A 10/3 UF wire is a versatile size, but it has clear limits.
If you are planning an underground run, measure twice, calculate the load, and check the burial depth before you buy the cable. A 10/3 UF wire can deliver reliable power for decades when it is installed correctly and protected from damage. When the run is long or the load is heavy, step up to a larger gauge rather than pushing 10 AWG to its limit. With the right planning, your outdoor circuit will be safe, code-compliant, and ready for whatever you plug in next.