versa lam beam

Versa Lam Beam: Sizes, Strength, and Best Uses Explained

By Emily Jackson
AD

A Versa-Lam beam is an engineered wood structural member made from laminated veneer lumber, or LVL, and manufactured by Weyerhaeuser. It is commonly used in residential and light commercial framing as a floor beam, garage door header, ridge beam, deck beam, or window and door header. Unlike a solid sawn timber beam, a Versa-Lam beam is built from thin wood veneers bonded together under heat and pressure, which gives it exceptional strength, straightness, and dimensional stability.

Builders and designers choose Versa-Lam beams when they need long spans, predictable performance, or a cleaner alternative to steel. The product is part of the broader LVL family, but the Versa-Lam name is a specific brand line with published design values and installation requirements. Understanding how it is made, graded, sized, and installed helps you use it safely and efficiently on any framing project.

What Is a Versa-Lam Beam and How Is It Made?

A Versa-Lam beam is a trademarked engineered wood product classified as laminated veneer lumber. It is produced by bonding many layers of thin wood veneers with a durable adhesive, with all veneer grains aligned parallel to the length of the beam. That parallel alignment is what allows the beam to resist bending far better than ordinary lumber of similar dimensions. The result is a dense, uniform member that can be manufactured in long lengths and consistent depths.

AD
LVL Span Table | Boise Cascade
LVL Span Table | Boise Cascade
LVL Widths & Depths
LVL Widths & Depths
SPAN AND SIZE CHARTS FOR LVL AND BCI JOISTS
SPAN AND SIZE CHARTS FOR LVL AND BCI JOISTS

Because it is engineered, a Versa-Lam beam can be manufactured to specific strength and stiffness values rather than relying on the natural variability of a tree. It is often used where solid lumber would be too small, too heavy, or too prone to warping. It also resists shrinking, twisting, and bowing better than many traditional framing materials, which makes it a favorite for precise structural work.

Composition and Manufacturing Process

The manufacturing process begins with logs that are peeled into thin veneers, similar to the way plywood is made. These veneers are dried, graded, and coated with an exterior-type adhesive. They are then stacked with the grain running in the same direction and pressed under intense heat and pressure until the adhesive cures. The finished billet is cut to width and length, then stamped with identifying information for the builder and inspector.

BCI® Joists
BCI® Joists
the kitchen is clean and ready to be used as an appliance for real estate
the kitchen is clean and ready to be used as an appliance for real estate
an instruction manual for the versa - lam beam details, with instructions on how to install
an instruction manual for the versa - lam beam details, with instructions on how to install

Manufacturing controls allow tight tolerances that are difficult to achieve with solid sawn lumber. A Versa-Lam beam can be produced in depths from roughly 3.5 inches to 24 inches or more, with common thicknesses of 1.75 inches, 3.5 inches, 5.25 inches, and 7 inches. Multiple plies can be nailed or bolted together to create a built-up beam with greater capacity. The manufacturer’s stamp identifies the grade, span rating, and design values needed for structural review.

Grades, Sizes, and Identification

Versa-Lam LVL is available in several grades, usually described by modulus of elasticity, or E. Common grades include 1.5E, 1.7E, and 2.0E, with higher numbers indicating greater stiffness and strength. A higher-grade beam can span farther or carry more load than a lower-grade beam of the same size. The grade stamp is not decorative; it tells the engineer, framer, and building official exactly what the beam is rated to do.

AD

Standard widths are often 1.75 inches, 3.5 inches, 5.25 inches, and 7 inches, while depths commonly range from 5.5 inches to 24 inches. Lengths can reach 60 feet or more, depending on the manufacturer and shipping limits. Some Versa-Lam products are treated for exterior use, but most are intended for interior dry-service conditions. Always verify the specific product data sheet because available sizes, grades, and treatments vary by region and supplier.

Boise Cascade Engineered Wood | Versa-Lam
Boise Cascade Engineered Wood | Versa-Lam
19+ Stylish Fake Beam Ideas for a Cozy Home
19+ Stylish Fake Beam Ideas for a Cozy Home
Beam 3
Beam 3
Beam element formulas
Beam element formulas
HEADER
HEADER
967K views · 6.3K reactions | How to Wrap an LVL Beam #diy #remodel #woodworking #construction #realestate #building #entrepreneur #interiordesign #carpentry #tools | WINNI
967K views · 6.3K reactions | How to Wrap an LVL Beam #diy #remodel #woodworking #construction #realestate #building #entrepreneur #interiordesign #carpentry #tools | WINNI

Structural Performance and Installation of Versa-Lam Beams

A Versa-Lam beam is designed by an engineer or selected from prescriptive code tables to carry floor, roof, or wall loads. Its high strength-to-weight ratio allows it to span farther than many solid sawn beams of comparable size. Deflection, which is how much the beam bends under load, is often the limiting factor rather than raw breaking strength. Too much deflection can cause drywall cracks, uneven floors, or a springy feel underfoot.

Proper installation matters as much as the beam’s published capacity. The beam must bear on adequate supports, be restrained against rotation, and be protected from moisture exposure. Cutting, notching, and drilling are restricted, and fasteners must be specified for the load and environmental conditions. Following the manufacturer’s installation guide and local building code is essential for a safe, code-compliant installation.

AD

Load Capacity, Spans, and Deflection

Load capacity depends on grade, depth, thickness, span, and load duration. For example, a 3.5-inch by 11.875-inch 2.0E Versa-Lam beam will carry more than a 1.75-inch by 11.875-inch beam of the same grade. Span tables from Weyerhaeuser or the applicable building code list allowable spans for common floor, roof, and header conditions. These tables assume proper bearing, lateral support, and uniform loads, so unusual loading conditions require separate engineering.

How I Used Foam Beams in My Home! 🤩
How I Used Foam Beams in My Home! 🤩
Faux Steel I-BEAM
Faux Steel I-BEAM

Deflection limits are typically L/360 for floors with brittle finishes and L/240 for many roof applications, though stricter limits may apply to tile, stone, or long-span floors. A beam can be strong enough to avoid failure yet still fail a deflection check. That is why engineers often choose a deeper beam rather than simply adding plies. For concentrated loads, point loads, cantilevers, or complex framing, a custom design is the only reliable approach.

Installation, Cutting, and Fastening

Versa-Lam beams should be stored flat, dry, and supported off the ground before installation. During framing, they must be placed with the correct face up if the beam is marked. They need continuous lateral support or blocking at bearing points and along the compression edge. Bearing length should meet code and manufacturer requirements, often at least 1.5 inches for end bearings and 3.5 inches for intermediate bearings, though larger bearings may be required for heavy loads.

AD

Cutting is generally allowed across the width and length, but notching or drilling is severely limited. Holes should only be placed according to the manufacturer’s hole chart, and field cuts should be sealed where moisture exposure is possible. Nails, screws, and bolts must be specified for multi-ply beams, because common nails alone may not provide the required shear transfer. Use structural screws or bolts with washers, follow the nailing schedule, and choose stainless or hot-dip galvanized fasteners in exterior or high-moisture areas.

When you specify a Versa-Lam beam, treat it as part of a complete structural system rather than a simple piece of wood. Confirm the grade stamp, verify the span table, and coordinate with your inspector or engineer before cutting or drilling. With the right design and installation, a Versa-Lam beam can deliver the long, straight, and dependable support that modern framing demands.

AD