STIHL MS 170 Bar and Chain: Best Replacement Sizes, Specs & Buying Guide
If you own a Stihl MS 170, you already understand why it holds the title of the best-selling chainsaw in North America. It is light, affordable, and surprisingly capable for a 30.1 cc homeowner saw. But the engine is only half the story. The bar and chain are the parts that actually meet the wood, and they take far more abuse than any other component on the machine. Running the wrong setup — or running a worn-out one — turns a sharp, eager little saw into a smoking, binding frustration.
This guide covers everything you need to know about the Stihl MS 170 bar and chain: the exact factory specifications, how to choose a replacement, when it makes sense to change bar length, and the maintenance habits that keep cutters sharp and bars straight. Whether you are ordering your first spare chain or trying to figure out why your saw keeps throwing the chain, the answers are below.
Stihl MS 170 Bar and Chain Specifications
From the factory, the MS 170 is typically sold with a 16-inch Stihl Rollomatic E bar, though a 14-inch version is also common depending on the dealer and the region. That bar runs a 3/8-inch Picco low-profile chain in .043-inch (1.1 mm) gauge. The combination is deliberately lightweight and low-kickback, which suits the saw's intended audience of homeowners, campers, and light storm-cleanup crews.
What surprises many new owners is that the MS 170 does not use standard 3/8-inch chain. It uses 3/8-inch Picco, also marketed as 3/8-inch low profile. The pitch measurement is the same number, but the drive links, cutters, and chassis are physically smaller. A full-size 3/8-inch chain will not fit this saw, and mixing them up is one of the most common ordering mistakes. Verify the markings stamped on your bar before you buy anything.
Bar Length, Gauge, and Drive Link Counts
The number of drive links is determined by bar length, and it must match exactly. A chain with the wrong link count will not sit properly in the bar groove and will either be impossible to tension or will jump the sprocket under load. Before ordering, count the links on your existing chain or read the drive link number stamped on the bar near the tail.
Gauge is the thickness of the drive link where it rides inside the bar groove, and it is measured in thousandths of an inch. The MS 170's factory setup is .043-inch, which is thinner and lighter than the .050-inch gauge used on larger Stihl saws. Some regional variants and older machines run .050-inch, so always match the gauge to the bar itself rather than assuming.
- 14-inch bar (35 cm): 3/8-inch Picco pitch, .043-inch gauge, 50 drive links
- 16-inch bar (40 cm): 3/8-inch Picco pitch, .043-inch gauge, 55 drive links
- Sprocket: 7-tooth spur sprocket, 3/8-inch Picco
- Bar mount: Stihl small mount pattern, often cross-referenced as Oregon A041
Chain Pitch and the 3/8 Picco Standard
Pitch is the average distance between three rivets, divided in half. On the MS 170 that works out to 3/8-inch Picco, a scaled-down chain family designed for saws under roughly 40 cc. Because the cutters are narrower and the kerf is thinner, the little 30.1 cc engine can pull the chain through hardwood without bogging down.
Stihl's factory chain for this saw is the Picco Micro 3, designated 63PM3. It is a semi-chisel, low-kickback chain with a green safety label, meaning it meets reduced-kickback requirements. If you want faster cutting in clean softwood, a full-chisel Picco chain like the 63PS3 is available, but it is more aggressive and less forgiving for inexperienced operators. For most MS 170 owners, the semi-chisel PM3 is the right call.
Choosing a Replacement Bar and Chain for Your MS 170
Replacement time usually arrives in one of three ways: the chain is worn beyond sharpening, the bar groove has opened up or the rails are burred, or the whole setup was destroyed by a pinch or a dirty cut. Whatever the reason, the safest path is to buy a matched bar-and-chain combo rather than assembling pieces from different sources.
Matched combos eliminate guesswork. The manufacturer has already confirmed that the pitch, gauge, link count, and bar mount all work together, and the chain has been pre-stretched and sized for that specific bar. It costs marginally more than buying a loose chain, but it removes an entire category of fitment errors that lead to thrown chains and damaged sprockets.
Genuine Stihl Versus Aftermarket Options
Genuine Stihl Rollomatic E bars and Picco chains are the benchmark. The bars have a laminated rail with a hardened nose sprocket, and the chains hold an edge well because the chrome plating on the cutters is consistent. If you cut firewood a few weekends a year, a genuine setup will likely outlast the saw itself.
Aftermarket options from Oregon, Husqvarna, and others can be excellent and often cost less. Oregon's 3/8-inch low-profile chains are widely available and perform well. The catch is fitment: you must match the mount code, gauge, pitch, and drive link count precisely, and cheap no-name chains from online marketplaces frequently have soft cutters that dull within a tank of fuel. Saving eight dollars on a chain that needs sharpening every twenty minutes is not a bargain.
Should You Change Bar Length or Chain Type?
Dropping to a 14-inch bar is a genuinely useful upgrade. On a 30 cc saw, a shorter bar means less chain to pull, which translates into faster cutting speed and less strain on the engine in hardwoods. If you mostly cut firewood in the 6 to 12-inch range, a 14-inch setup will feel noticeably snappier than the stock 16-inch.
Going the other direction is where people get into trouble. An 18-inch bar on an MS 170 pushes the saw past its comfort zone, causing the engine to bog, the oiler to struggle, and the powerhead to run hotter. It also moves the center of gravity forward and makes kickback more likely. Keep the MS 170 at 14 or 16 inches and let a bigger saw handle the larger timber.
Installing, Tensioning, and Maintaining the Setup
A properly installed bar and chain should take about five minutes to fit and tension. The MS 170 uses a side-access tensioning screw, which means you do not need a scrench to reach behind the sprocket cover. That said, small errors in the installation process are responsible for most of the chain problems owners report.
Maintenance is equally straightforward. Two-stroke chainsaws reward a little attention: clean the bar groove, flip the bar regularly, keep the oil tank full, and touch up the cutters with a file every couple of tanks of fuel. Do those four things and you will get years of service out of a setup that costs less than a tank of gas.
Mounting the Bar and Setting Chain Tension
Start by removing the sprocket cover and cleaning out the packed sawdust and oil sludge behind it, especially around the oiler port and the bar groove. A blocked oil passage starves the bar and chain of lubrication, which rapidly overheats the rails and stretches the chain. Seat the bar on the studs, loop the chain over the sprocket with the cutters facing forward on top, and slide the bar back so the chain seats in the groove.
Set tension with the bar tip raised slightly. The chain should sit snug against the underside of the bar, and you should still be able to pull it around the bar by hand with a little resistance. Snug is the target — a chain that hangs visibly loose will jump the sprocket, while one that is overtightened will burn up the bar nose sprocket and the clutch. After the first thirty minutes of cutting, expect the chain to stretch and retension it.
Sharpening and Routine Care for Longer Life
Stihl 3/8-inch Picco chain takes a 5/32-inch (4.0 mm) round file. Hold the file at the angle marked on the cutter — 30 degrees for the top plate — and stroke away from the cutting edge. Three or four light passes per cutter is usually enough if you sharpen often rather than waiting until the chain is completely dull. Check the depth gauges every few sharpenings and file them down to 0.025-inch as needed.
Beyond sharpening, rotate the bar every time you swap chains so the rails wear evenly, and clean the groove with a thin scraper or a piece of wire. Use genuine bar and chain oil rather than motor oil, since it is formulated to cling to a fast-moving chain. A spare chain kept sharp in a plastic case means you are never stuck mid-job with a dull cutter and a pile of unsplit rounds.
Keeping a second bar and chain on the shelf turns a stalled afternoon into a two-minute swap, and it means you are never forced into an emergency purchase at whatever price the nearest store happens to be charging. Measure your bar, write the pitch, gauge, and drive link count on a piece of tape inside your toolbox, and order with confidence when the time comes. Your MS 170 will keep earning its keep for years.