Steel Stud Sizes: Complete Guide to Dimensions, Gauges, and Framing Charts
Steel stud sizes are more than a single number on a framing plan. They describe a cold-formed metal shape with a web depth, flange width, return lip, steel thickness, yield strength, and coating. Whether you are framing a basement wall, a commercial corridor, or an exterior curtain wall, the size you choose controls strength, stiffness, insulation depth, and how easily drywall or sheathing can be attached.
Because steel studs are manufactured in a wide range of standard dimensions, mixing up a 3-5/8-inch stud with a 6-inch structural member can lead to callbacks, failed inspections, or wasted material. This guide breaks down the steel stud sizes you will see most often, explains how to read manufacturer callouts, and shows how to match studs, tracks, and spacing to the job at hand.
Understanding Steel Stud Dimensions and Terminology
Steel studs are produced by cold-forming thin-gauge steel into a C-shaped section. The main dimensions are the web depth, the flange width, the return lip, and the base metal thickness. Web depth is the overall width of the stud and is usually written in hundredths of an inch in manufacturer callouts. Flange width is the flat face where screws are driven, while the return lip adds stiffness and helps prevent the flange from twisting.
A typical callout looks like 362S125-33. The first three digits, 362, indicate a 3.62-inch web depth, which is the nominal 3-5/8-inch stud. The letter S means stud; T would mean track. The next three digits, 125, indicate a 1.25-inch flange. The final number, 33, indicates 33-mil steel thickness, which is commonly called 20-gauge. Learning this shorthand makes it much easier to compare steel stud sizes across manufacturers.
Web Depth and Flange Width
Web depth is the most visible steel stud size. It determines how thick the finished wall will be and how much room is available for insulation, wiring, plumbing, and blocking. Common web depths include 1-5/8 inches, 2-1/2 inches, 3-5/8 inches, 4 inches, 6 inches, 8 inches, 10 inches, and 12 inches. Shallower studs are used for furring and tight partitions, while deeper studs are used for plumbing walls, structural walls, and exterior framing.
Flange width affects stiffness and screw attachment. Standard flanges are often 1-1/4 inches, 1-3/8 inches, 1-5/8 inches, or 2 inches. A wider flange gives drywall installers more room for screws and can reduce flange rotation under load. For example, a 362S125-33 stud has a 1-1/4-inch flange, while a 600S162-54 stud has a 1-5/8-inch flange and a much heavier 54-mil thickness.
Gauge, Mils, and Thickness
Gauge is a traditional way to describe steel thickness, but it can be confusing because a lower gauge number means a thicker stud. In steel framing, common thicknesses include 25-gauge at 18 mil, 20-gauge at 33 mil, 18-gauge at 43 mil, 16-gauge at 54 mil, 14-gauge at 68 mil, and 12-gauge at 97 mil. One mil equals one-thousandth of an inch, so 33 mil is 0.033 inch of base steel thickness before coatings.
Thickness works together with web depth to determine load capacity. A 3-5/8-inch stud in 20-gauge may be fine for a non-load-bearing interior partition, but the same web depth in 16-gauge may be required for a taller wall or a fire-rated assembly. Structural and exterior applications often use 16-gauge, 14-gauge, or 12-gauge steel, while interior drywall studs commonly use 25-gauge or 20-gauge material.
Common Steel Stud Sizes by Application
Steel stud sizes follow industry patterns, but manufacturers may offer slightly different dimensions and thicknesses. The most common interior drywall stud is the 3-5/8-inch web with a 1-1/4-inch flange in 25- or 20-gauge steel. It fits standard electrical boxes, accepts 5/8-inch gypsum board, and works with widely available tracks and accessories. Other sizes are chosen when the wall needs to be shallower, deeper, stronger, or more fire-resistant.
Structural steel studs are a different category. They are engineered for axial loads, transverse loads, or both, and they are often specified by a structural engineer. These studs may have deeper webs, wider flanges, and heavier gauges. They also require matching tracks, bridging, and bracing. Exterior studs add galvanized coatings such as G40, G60, or G90 to resist corrosion, and their sizes must account for wind pressure, deflection limits, and thermal movement.
Interior Partition and Drywall Studs
For interior partitions, the workhorse sizes are 1-5/8-inch, 2-1/2-inch, 3-5/8-inch, 4-inch, and 6-inch web depths. The 1-5/8-inch stud is often used for furring out concrete or masonry walls, while 2-1/2-inch studs create shallow partitions around small pipes or conduit. The 3-5/8-inch stud remains the most popular because it provides enough depth for standard wiring and a familiar wall thickness for door frames and trim.
A typical interior callout might be 362S125-33, meaning a 3-5/8-inch web, 1-1/4-inch flange, and 33-mil thickness. For a deeper plumbing wall, a 600S125-33 or 600S162-33 stud may be used. If the wall is load-bearing or rated for fire, the specifier may move up to 362S125-43 or 362S162-54. Always check the approved assembly drawing, because the same wall height can require different steel stud sizes depending on spacing, board type, and loading.
Structural and Exterior Steel Studs
Structural steel studs commonly range from 3-5/8 inches to 12 inches in web depth, with flanges from 1-5/8 inches to 2-1/2 inches and thicknesses from 33 mil to 97 mil or more. A 6-inch, 16-gauge stud such as 600S162-54 is a common commercial size, while 8-inch, 14-gauge studs like 800S200-68 may be used for taller exterior walls. Jamb studs, headers, and columns often use nested or back-to-back studs to increase capacity without changing the wall depth.
Exterior framing also depends on coating and connection details. A G60 or G90 galvanized coating is typical in humid or coastal environments, and the stud size must be compatible with sheathing, cladding, and thermal breaks. For example, a curtain wall might use 600S162-54 studs at 16 inches on center with a matching 600T162-54 track, while a high-wind area could require 800S200-68 studs at 12 inches on center. These decisions belong with a licensed engineer and the project specifications.
How to Choose the Right Steel Stud Size
Choosing a steel stud size starts with the wall's purpose. Is it a non-load-bearing room divider, a load-bearing interior wall, a shear wall, or an exterior envelope? Wall height, lateral loads, axial loads, deflection limits, and fire ratings all influence the answer. A 10-foot-tall partition may use 3-5/8-inch studs at 16 inches on center, while a 20-foot-tall exterior wall may need 8-inch studs at 12 inches on center with additional bracing.
Coordination with mechanical, electrical, and plumbing systems is equally important. A 2-1/2-inch stud may not leave enough room for a drain pipe, and a 6-inch stud may be necessary to avoid furring out a wet wall. Fire-rated assemblies, acoustic-rated walls, and shaft walls often prescribe exact stud sizes and gauges. The best approach is to review the architectural and structural drawings, then verify the selected size against the manufacturer's span tables and local building codes.
Matching Studs, Tracks, and Spacing
Tracks are the horizontal members that hold the studs in place at the floor and ceiling. They should match the stud's web depth and be selected with a compatible leg length and gauge. A 3-5/8-inch stud uses a 3-5/8-inch track, and a 6-inch structural stud uses a 6-inch structural track. Mixing nominal sizes from different systems can create loose fits, poor screw alignment, and reduced load capacity.
Stud spacing also changes the required size. Common spacings are 12 inches, 16 inches, and 24 inches on center. Sixteen inches on center is standard for many commercial and residential walls, while 24 inches on center may be acceptable for light nonstructural partitions with thicker gypsum board. For example, 362S125-33 studs at 16 inches on center with 362T125-33 tracks are a common interior assembly. A structural wall might use 600S162-54 studs at 16 inches on center with 600T162-54 tracks, or heavier studs at 12 inches on center if loads are high.
Reading Manufacturer Callouts and Specs
Manufacturer catalogs list far more than the basic size. They provide section properties such as moment of inertia, section modulus, effective width, and web crippling strength. They also publish allowable span tables for different loading conditions, spacings, and bracing details. The callout 362S162-54, for instance, tells you the web depth, member type, flange width, and mil thickness, but the span table tells you whether that stud can safely span 12 feet at 16 inches on center under a given load.
Pay attention to yield strength and coating as well. Nonstructural studs are often made from 33-ksi steel, while structural studs may be 50-ksi or higher. ASTM C645 covers nonstructural steel framing members, and ASTM C955 covers load-bearing steel studs and tracks. Galvanized coatings are specified by ASTM A653 or A1003. When a project is governed by code, these standards and the engineer's stamped drawings take priority over generic size charts.
Practical Tips and Common Mistakes
One of the most common mistakes is assuming that gauge alone determines strength. A 20-gauge stud with a 6-inch web can be stronger in bending than a 20-gauge stud with a 3-5/8-inch web, even though both have the same thickness. Web depth, flange width, yield strength, bracing, and span all work together. Another mistake is using a track that is too light or too short in the leg, which can allow the stud to rotate or pull away under load.
Availability matters, too. Not every supplier stocks every steel stud size. The 3-5/8-inch, 20-gauge stud is widely available, as are 6-inch, 16-gauge structural studs in many markets. Deeper webs, heavier gauges, and custom flange widths may require special order. Lengths are commonly 8, 10, 12, 16, and 20 feet, but longer members can be ordered for tall walls. Planning around standard stock sizes can reduce cost and lead time.
Mixing Metric and Imperial Sizes
In many parts of the world, steel stud sizes are given in metric units. Common web depths include 50 mm, 70 mm, 90 mm, 100 mm, 150 mm, and 200 mm, with thicknesses such as 0.55 mm, 0.75 mm, 1.0 mm, and 1.2 mm. These metric sizes are close to imperial dimensions but not always interchangeable. A 90 mm stud is close to 3-1/2 inches, while a 150 mm stud is close to 6 inches, but the flange widths, lips, and coating specifications may differ.
When working on an international project or with imported materials, do not force a metric stud into an imperial track or vice versa. The screw holes, nesting tolerances, and structural properties may not match. Check the manufacturer's literature for both the stud and track, and confirm that the assembly has been tested or engineered as a complete system. If the drawings are in metric, order metric components; if they are in imperial, stay with imperial sizes unless an engineer approves a substitution.
When to Consult an Engineer
Consult a structural engineer for any load-bearing wall, exterior wall, tall partition, shear wall, or assembly with heavy finishes or large openings. The engineer will specify the steel stud size, gauge, spacing, bracing, and connection details based on actual loads. This is especially important in seismic zones, high-wind regions, and buildings with multiple stories, where small sizing errors can have serious consequences.
Bring the engineer a clear set of drawings, wall heights, opening locations, and anticipated loads. If the wall must meet a fire-resistance rating, provide the UL or GA file number so the stud size and gauge can be verified against the tested assembly. A few minutes of engineering review can prevent expensive rework and ensure the finished wall performs as intended.
Choosing the right steel stud size comes down to matching the demands of the wall with the available web depths, flange widths, and steel thicknesses. Keep a manufacturer catalog or span table nearby, verify every callout before ordering, and let code requirements and engineering judgment guide the final selection. With that approach, your metal framing will go up faster, pass inspection with fewer surprises, and stand ready for drywall, sheathing, and whatever the building needs next.