HSS Drill Speeds and Feeds Chart: Ultimate RPM & Feed Rate Guide
An HSS drill speeds and feeds chart is one of the most practical tools in any shop, whether you are drilling a single hole in a drill press or running a production batch on a CNC. It gives you a starting point for spindle speed and feed rate so you can cut efficiently without burning through drill bits. But a chart is only useful if you understand what the numbers mean and how your machine, material, and setup change the ideal values.
If you have ever watched a high-speed steel bit turn blue, squeal, or snap in the middle of a hole, the problem usually comes down to speed, feed, or chip evacuation. This guide breaks down how to read an HSS drill speeds and feeds chart, how to calculate RPM and feed rate, and how to adjust the numbers for real-world materials and machines.
Understanding HSS Drill Speeds and Feeds
High-speed steel remains a favorite for drilling because it is tough, affordable, and forgiving compared with carbide. HSS bits tolerate interrupted cuts, hand-fed drill presses, and less rigid setups better than many harder tool materials. That forgiveness does not mean you can ignore speeds and feeds. It simply means the sweet spot is wider and the consequences of being slightly off are often less catastrophic.
Speed and feed work together. Speed is how fast the cutting edge moves through the material, usually expressed as surface feet per minute or meters per minute and converted into spindle RPM. Feed is how fast the drill advances into the work, usually expressed as inches per revolution or millimeters per revolution. An HSS drill speeds and feeds chart ties those two values to the material and drill diameter.
What Speed and Feed Actually Mean
Surface speed is the speed of the drill's outer edge, not the spindle. A large drill turning at the same RPM as a small drill has a much higher surface speed because its circumference is larger. That is why an HSS drill speeds and feeds chart often lists cutting speed by material and then requires you to calculate RPM based on drill diameter.
Feed is the distance the drill travels into the hole with each revolution. Feed rate in inches per minute equals RPM multiplied by feed per revolution. For a two-flute drill, the chip load per tooth is roughly the feed per revolution divided by two. Too little feed can rub the edge and work-harden some materials, while too much feed can overload the drill and cause breakage.
Why HSS Behaves Differently Than Carbide
HSS is softer and less heat-resistant than carbide, so it needs lower surface speeds and usually more coolant. Carbide can run two to five times faster in many materials, but it is more brittle and less tolerant of vibration, interrupted cuts, and poor setup. HSS drills are more likely to dull gradually, while carbide can chip or fracture suddenly.
In an HSS drill speeds and feeds chart, you will often see conservative ranges. Stainless steel might call for 30 to 50 surface feet per minute with HSS, while carbide tooling may run at 150 to 250 or higher. On a manual mill or drill press, those conservative HSS values are often the difference between a clean hole and a ruined bit.
How to Read and Use an HSS Drill Speeds and Feeds Chart
Most charts are organized by material group and drill diameter. You find the material you are cutting, locate the drill size, and read the recommended surface speed and feed per revolution. Some charts give RPM directly, but many give cutting speed so you can calculate RPM for any diameter. Always check whether the chart uses inches, millimeters, surface feet per minute, or meters per minute.
A chart cannot know your setup. Machine rigidity, coolant delivery, hole depth, drill point geometry, coating, and workpiece hardness all affect the best speed and feed. Treat the chart as a baseline, not a law. Start within the recommended range, watch the chips, listen to the cut, and adjust before the drill overheats.
Finding Surface Speed and RPM
If the chart lists surface speed in SFM, use this formula for inch dimensions: RPM equals SFM multiplied by 3.82, divided by drill diameter in inches. For example, a 1/2 inch HSS drill in mild steel at 100 SFM would run at 100 times 3.82 divided by 0.5, which equals 764 RPM. Rounding to 750 RPM is usually fine on a manual machine.
For metric work, RPM equals meters per minute multiplied by 1000, divided by pi times drill diameter in millimeters. If a chart gives SFM instead, convert or use the approximation RPM equals SFM times 304.8 divided by pi times diameter in millimeters. For example, a 10 mm drill at 25 meters per minute would run near 796 RPM.
Setting Feed Rate and Chip Load
Feed per revolution depends heavily on drill diameter. Small drills need light feed because the web and flutes are weak. Large drills can take more feed because they have greater rigidity and more mass. A typical HSS range might be 0.001 to 0.003 inches per revolution for a 1/16 inch drill, 0.004 to 0.007 for 1/4 inch, 0.007 to 0.010 for 1/2 inch, and 0.010 to 0.015 for 1 inch.
In metric terms, a 1 mm drill may run around 0.02 to 0.05 mm per revolution, a 6 mm drill around 0.08 to 0.15, a 12 mm drill around 0.15 to 0.25, and a 25 mm drill around 0.25 to 0.40. To find feed rate in inches per minute, multiply RPM by feed per revolution. At 750 RPM and 0.008 inches per revolution, the feed rate is 6 inches per minute.
Common Materials and Practical Adjustments
The material group is the single biggest factor in any HSS drill speeds and feeds chart. Aluminum, brass, and plastics generally allow high speeds and moderate feeds. Mild steel sits in the middle. Stainless steel, titanium, and high-alloy steels demand slower speeds and careful feed control to avoid work hardening and rapid edge wear.
Material condition matters just as much as the material name. A 1018 mild steel plate cuts differently from 4140 pre-hard, and 304 stainless behaves differently from 316. Cast skin, scale, heat treatment, and abrasiveness can all push you toward the low end of the chart. Start conservative, then increase speed or feed only when the cut proves stable.
Typical HSS Speed Ranges by Material
Aluminum often runs from 200 to 300 SFM, or roughly 60 to 90 meters per minute, with feed rates that clear chips aggressively. Brass and bronze commonly run from 150 to 250 SFM, while many plastics can handle 200 to 400 SFM with sharp bits and light feed. In all three cases, chip evacuation matters more than raw speed.
Mild steel typically falls between 80 and 110 SFM. Stainless steel such as 304 often calls for 30 to 50 SFM. Cast iron commonly runs 60 to 100 SFM, titanium around 20 to 40 SFM, and tool steels around 40 to 70 SFM. Coatings and coolant can shift these numbers, but they do not turn HSS into carbide.
When to Slow Down or Speed Up
Slow down for deep holes, poor chip evacuation, hard spots, interrupted cuts, long drill overhang, manual drill presses, and any situation where coolant is limited. Stainless steel is especially sensitive to rubbing, so if you slow the speed too much without maintaining feed, the surface can work-harden and dull the drill quickly.
Speed up cautiously when cutting soft, gummy materials with good chip clearance, but never faster than the drill and machine can handle safely. Signs that you need to slow down include blue chips, burning smell, squealing, drill discoloration, and rounded cutting edges. Signs that feed is too light include fine dust, rubbing, heat at the tip without real cutting, and work-hardened stainless.
Coolant, Coatings, and Drill Geometry
Coolant type and delivery can change the effective speed and feed for an HSS drill. Flood coolant removes heat and flushes chips, mist coolant lubricates and cools lightly, and peck drilling helps clear chips from deep holes. Through-spindle coolant is ideal when the machine supports it, but many manual setups rely on cutting oil and frequent pecking.
Coatings such as black oxide, titanium nitride, and titanium carbonitride can reduce friction and slightly extend tool life. They may allow a modest increase in speed or feed, but they do not rewrite the basic limits of high-speed steel. A coated drill run at carbide speeds will still fail, often faster because the coating hides the heat damage until the edge breaks down.
Applying Chart Values on Manual vs CNC Machines
On a manual drill press, start 10 to 20 percent below the chart RPM and feed by feel. Clamp the workpiece, use cutting oil, and peck deep holes to clear chips. If the drill grabs, reduce feed and improve rigidity. If the drill rubs, increase feed slightly or reduce speed depending on the material and chip appearance.
On a CNC machine, you can hold more consistent speeds and feeds, but toolholder runout and chip evacuation become critical. Calculate feed rate from RPM and feed per revolution, then use peck cycles for deep holes. Start around 75 to 80 percent of the chart value, inspect the chips, and increase in small steps while watching spindle load and hole quality.
Building Your Own HSS Drill Chart
Use manufacturer data as a baseline, then test on scrap pieces of the same material. Record the drill size, RPM, feed rate, coolant, hole depth, chip color, and tool life. Over time, you will build a shop-specific HSS drill speeds and feeds chart that reflects your machines, fixtures, and typical materials better than any generic table.
Record failures as carefully as successes. A broken 1/4 inch drill in stainless at 600 RPM and 0.006 inches per revolution tells you something useful. A work-hardened hole at 200 RPM and 0.002 inches per revolution tells you the feed was too light. That kind of data turns guesswork into a repeatable process.
With a reliable HSS drill speeds and feeds chart as your starting point, the real improvement comes from paying attention to the cut. Keep notes, change one variable at a time, and let the chips show you whether the drill is cutting efficiently or just creating heat. The next hole can always be cleaner, faster, and easier on your tooling than the last.