drilling speeds and feeds

Drilling Speeds and Feeds: The Ultimate Guide to Faster, Cleaner Holes

By Thomas Jones
AD

Drilling speeds and feeds are the two numbers that decide whether a hole is cut cleanly, quickly, and economically or whether you burn through drill bits and scrap parts. Speed refers to how fast the outer edge of the drill moves through the material, while feed describes how far the drill advances into the workpiece with each revolution. Get these variables right, and drilling becomes predictable; get them wrong, and you invite chatter, broken tools, oversized holes, and poor surface finish.

Whether you are working on a manual drill press, a CNC mill, or a high-production machining center, the principles remain the same. The challenge is that the correct values change with the workpiece material, drill diameter, tool material, coating, coolant, and rigidity of the setup. This guide breaks down the formulas, practical examples, and shop-tested adjustments that help you dial in drilling speeds and feeds with confidence.

The Foundation: What Drilling Speeds and Feeds Actually Control

It helps to think of drilling as a two-part motion. The spindle rotates the drill, and the drill translates downward into the material. Cutting speed is tied to the rotation, while feed is tied to the translation. Together they determine the chip thickness, the heat generated, the load on the drill point, and the rate at which material is removed.

AD
Drill Speed and Feed Calculator
Drill Speed and Feed Calculator
The best 4mm drill bit for drilling through metals
The best 4mm drill bit for drilling through metals
Industrial Drilling Machine Speed and Feed: How to Set the Right Parameters
Industrial Drilling Machine Speed and Feed: How to Set the Right Parameters

Many machinists confuse spindle speed with cutting speed. Spindle speed is RPM, a raw rotational value. Cutting speed is the surface speed at the drill's outer diameter, usually expressed in surface feet per minute (SFM) or meters per minute (m/min). A small drill at high RPM can have the same cutting speed as a large drill at low RPM. That distinction is critical because tool life depends on surface speed, not simply on how fast the spindle turns.

Cutting Speed (SFM and m/min)

Cutting speed represents how fast the cutting edge travels through the material. For drilling, the maximum speed occurs at the outer corner of the drill, where the diameter is largest. If that outer edge moves too slowly, the drill may rub instead of cut, causing work hardening and poor chip formation. If it moves too fast, the cutting edge overheats, wears rapidly, and can fail suddenly.

ALPEN HSS 2mm Jobber Drill Bit for Precision Drilling - 2 Pack
ALPEN HSS 2mm Jobber Drill Bit for Precision Drilling - 2 Pack
Drill Press Speed Chart - Instruments Download Printable PDF
Drill Press Speed Chart - Instruments Download Printable PDF
an info sheet describing how to use the machine for cutting and feeding seed or plants
an info sheet describing how to use the machine for cutting and feeding seed or plants

Recommended cutting speeds are usually published in charts or tool catalogs. For example, high-speed steel (HSS) drills in mild steel might run around 80 to 100 SFM, while carbide drills in aluminum can exceed 300 to 500 SFM. Stainless steel often calls for lower surface speeds, sometimes 30 to 60 SFM with HSS, because it work-hardens and retains heat. These starting values are not laws; they are reference points that you refine based on coolant, rigidity, and hole depth.

Feed Rate (IPR and mm/rev)

Feed rate is the distance the drill advances per revolution, typically measured in inches per revolution (IPR) or millimeters per revolution (mm/rev). If the feed is too light, the cutting edge may rub, dull quickly, and generate excessive heat. If the feed is too heavy, the drill can chip, deflect, or stall the spindle, especially in small diameters or long reach applications.

AD

Feed also controls chip thickness. A proper feed creates a chip that is thick enough to carry heat away from the cutting zone. In softer materials like aluminum, higher feed per revolution is usually acceptable. In harder or work-hardening materials, a moderate feed that keeps the tool engaged is often better than a very light feed that encourages rubbing. Always check the drill manufacturer's recommendations, because carbide and coated drills often tolerate different feed ranges than uncoated HSS.

Alpen HSS Cobalt Drill Bit 3.5mm - Precision for Hard Materials
Alpen HSS Cobalt Drill Bit 3.5mm - Precision for Hard Materials
Manage costs by drilling efficiently
Manage costs by drilling efficiently
Feeds and Speeds Calculator — Milling
Feeds and Speeds Calculator — Milling
the drill press speed chart is shown in this diagram, with instructions for how to use it
the drill press speed chart is shown in this diagram, with instructions for how to use it
a drill is being used to cut through the concrete with a large metal spiral on it's side
a drill is being used to cut through the concrete with a large metal spiral on it's side
the speed chart for this motorcycle is shown
the speed chart for this motorcycle is shown

Calculating Drilling Speeds and Feeds for CNC and Manual Machines

Once you understand the variables, the next step is turning them into machine settings. The two calculations you need are spindle speed in RPM and feed rate in inches per minute (IPM) or millimeters per minute (mm/min). You can calculate them by hand, use a calculator, or rely on CAM software, but knowing the math helps you troubleshoot when the cut does not sound or look right.

For manual machines, you often set RPM directly and feed by hand or with a power feed. On CNC machines, you program the RPM with an S command and the feed rate with an F command. In both cases, the starting point should come from the workpiece material, drill diameter, and tool material. Rigidity and coolant then determine whether you stay at the calculated values or adjust them up or down.

AD

The RPM Formula and Practical Examples

The standard formula for spindle speed is: RPM = (SFM × 3.82) ÷ Drill Diameter. The number 3.82 converts surface feet per minute and diameter in inches into revolutions per minute. In metric, the formula is: RPM = (m/min × 1000) ÷ (π × Drill Diameter in mm). Both formulas give you a starting RPM based on the recommended cutting speed.

Alpen HSS Jobber Drill Bit 7.0mm - High-Speed Steel, Durable & Efficient
Alpen HSS Jobber Drill Bit 7.0mm - High-Speed Steel, Durable & Efficient
Alpen HSS Drill Bits 7.5mm 10 Piece Set for Precision Drilling
Alpen HSS Drill Bits 7.5mm 10 Piece Set for Precision Drilling
How to Measure Drill Press Speed for Perfect Drilling
How to Measure Drill Press Speed for Perfect Drilling
Alpen HSS Jobber Drill Bit 9.0mm - Precision Steel Cutting Tool
Alpen HSS Jobber Drill Bit 9.0mm - Precision Steel Cutting Tool

For example, suppose you are drilling a 0.500-inch hole in mild steel with an HSS drill at 90 SFM. The calculation is (90 × 3.82) ÷ 0.500, which equals 687.6 RPM. If you switch to a 0.250-inch drill at the same 90 SFM, the RPM becomes (90 × 3.82) ÷ 0.250, or 1,375 RPM. The smaller drill needs more RPM to maintain the same surface speed. That is why small drills often run at high spindle speeds while large drills run much slower.

Feed Rate, Cycle Time, and Chip Load

After calculating RPM, determine feed rate. Feed rate in IPM equals RPM × IPR. If your 0.500-inch drill runs at 688 RPM and the recommended feed is 0.008 IPR, the feed rate is 688 × 0.008, or about 5.5 IPM. In metric, feed rate in mm/min equals RPM × mm/rev. These values let you estimate cycle time and compare the productivity of different tool paths.

AD

Cycle time for a drilled hole is simply hole depth divided by feed rate, plus any peck retract time. For a 1-inch deep hole at 5.5 IPM, the cutting time is about 0.18 minutes, or roughly 11 seconds, assuming one pass without pecks. Add peck retracts for deep holes, and the cycle time increases. This is why balancing speed and feed matters: pushing too hard may break the drill, but running too conservatively can double or triple the cost per hole.

Material, Tooling, and Advanced Drilling Strategies

No single chart covers every drilling situation. The workpiece material, drill material, coating, geometry, and machine condition all influence the ideal speeds and feeds. A value that works perfectly in one shop may fail in another because of differences in coolant pressure, spindle taper, or workholding stiffness. Use published data as a baseline, then listen to the cut, inspect the chips, and measure the hole.

Tool selection is just as important as the numbers. A split-point carbide drill behaves differently from a 118-degree HSS jobber drill. A cobalt drill may handle higher temperatures than standard HSS, while a coated carbide drill can run much faster in abrasive materials. The goal is to match the tool's capability to the material and the machine's capability to the tool.

Matching Speeds and Feeds to Workpiece Materials

Aluminum and brass generally allow high cutting speeds and aggressive feeds because they machine easily and conduct heat well. A carbide drill in aluminum might run at 300 to 500 SFM or more, with feed rates that produce large, free-flowing chips. Plastics need sharp tools, high RPM, and moderate feed to avoid melting; coolant or air blast helps clear chips and control heat.

Mild steel and alloy steel sit in the middle range. HSS drills often run at 80 to 120 SFM, while carbide can run higher if the setup is rigid. Stainless steel demands lower surface speeds and consistent feed to avoid work hardening. Cast iron machines well but produces abrasive dust, so carbide and good chip evacuation are valuable. Titanium and high-temperature alloys require very conservative speeds, rigid setups, and often high-pressure coolant.

Peck Drilling, Coolant, and Rigidity

Peck drilling breaks the chip and allows coolant to reach the cutting edge. It is essential for deep holes where chip evacuation is difficult. As a rule of thumb, peck depth can start at one to three times the drill diameter, but deep holes may require smaller pecks. The trade-off is cycle time: every retract adds non-cutting time, so use the largest safe peck that still clears chips.

Coolant type and delivery matter as much as the speed and feed numbers. Flood coolant helps with heat and chip flushing, while through-tool coolant is superior for deep holes because it pushes chips out of the flutes. Machine rigidity and workholding also play a huge role. If the part vibrates or the drill deflects, reduce speed and feed until the cut is stable, then optimize from there. A rigid setup can often run faster and produce better hole quality than a loose one at conservative settings.

The most reliable way to master drilling speeds and feeds is to start with proven recommendations, document what happens, and adjust one variable at a time. Keep a log of material, drill size, coating, RPM, feed, coolant, and hole quality. Over time, that log becomes more valuable than any generic chart because it reflects your machines, your tooling, and your production goals. The next hole you drill can be faster, cleaner, and more cost-effective than the last one if you treat every setup as a chance to learn.

AD