craftsman table saw blade won't raise

Craftsman Table Saw Blade Won't Raise? Here's How to Fix It Fast

By Andrew Davis
AD

You turn the handwheel on your Craftsman table saw, expecting the blade to rise, but nothing happens. If your Craftsman table saw blade won't raise, you're not alone. This is one of the most common complaints owners have with older and mid-range saws, especially after months of cutting plywood, pressure-treated lumber, or MDF. The good news is that the elevation system on most Craftsman saws is simple, mechanical, and often repairable without a trip to a service center.

Before you force the handwheel or start disassembling the saw, unplug it from the power source. The blade elevation mechanism relies on a handwheel, shaft, worm gear, and trunnion, and any binding in that chain can stop the blade from moving. Some problems take five minutes to fix, while others require parts replacement. This guide walks through the likely causes, from a forgotten lock knob to stripped gears, and explains how to diagnose and repair each one safely.

Common Causes of a Craftsman Table Saw Blade That Won't Raise

The first thing to understand is how your saw raises the blade. When you turn the elevation handwheel, it rotates a shaft connected to a worm gear. That worm gear meshes with a trunnion gear or bracket under the table, which moves the arbor and blade up or down. If the handwheel spins freely but the blade does not move, the problem is usually a loose connection or stripped gear. If the handwheel will not turn at all, the mechanism is likely jammed, locked, or packed with debris.

AD
two pictures showing how to use a circular sawtoother for cutting wood and metal
two pictures showing how to use a circular sawtoother for cutting wood and metal
a close up of a circular saw blade on a white background
a close up of a circular saw blade on a white background
How to Adjust a Craftsman Table Saw Blade
How to Adjust a Craftsman Table Saw Blade

On many Craftsman models, including the popular 113, 315, and 137 series, the elevation gears are exposed under the table. That means sawdust, pitch, and rust can accumulate directly on the teeth. A small amount of hardened resin can create enough resistance to stop the blade from raising. Before you assume the worst, check the simple stuff: the lock knob, the bevel lock, and the cleanliness of the gear teeth.

The Elevation Lock Knob Is Still Engaged

Many Craftsman table saws have a lock knob located in the center of the elevation handwheel or just under the front rail. This knob locks the blade height so it will not drift during a cut. If someone tightened it and forgot to release it, the handwheel may feel stuck or the blade may refuse to rise. Some owners mistake this for a broken gear because the handwheel will not budge at all.

The 8 Best Table Saw Blades
The 8 Best Table Saw Blades
Table Saw Blades - Start Using The Right Blade For The Cut
Table Saw Blades - Start Using The Right Blade For The Cut
a machine that is sitting in the middle of a room with other machines behind it
a machine that is sitting in the middle of a room with other machines behind it

Turn the lock knob counterclockwise until it is completely loose, then test the handwheel again. On saws with a separate bevel lock, make sure that lock is also released, because it can clamp the trunnion and prevent elevation movement. If the blade still will not raise after both locks are free, move on to cleaning and inspection. Do not force the handwheel, as you can bend the elevation rod or strip gear teeth.

Sawdust, Pitch, and Rust Have Jammed the Gears

The elevation gears on a Craftsman table saw are often located in a place where dust naturally falls. Over time, fine sawdust mixes with natural wood resins and hardens into a concrete-like paste. Rust can also form on exposed steel shafts and trunnion surfaces, especially in humid shops. The result is a handwheel that feels gritty, stiff, or completely stuck.

AD

To fix this, unplug the saw, remove the throat plate and blade, and look under the table with a flashlight. Use a stiff brush, vacuum, and a pick to remove packed debris from the worm gear and trunnion teeth. Apply a dry-film lubricant, paste wax, or paraffin to the gear teeth and sliding surfaces. Avoid heavy grease because it attracts more dust. Work the handwheel back and forth through its full range to distribute the lubricant. If the blade still will not raise, the problem is mechanical.

a table saw is shown with instructions for how to use the blade and blades on it
a table saw is shown with instructions for how to use the blade and blades on it
Delta table saw blade won't go up or down
Delta table saw blade won't go up or down
a circular saw blade with the word woodwork on it's side and an image of
a circular saw blade with the word woodwork on it's side and an image of
Top Picks: Best Combination Blades for Your Table Saw
Top Picks: Best Combination Blades for Your Table Saw
The 3 Table Saw Blades You Need - FineWoodworking
The 3 Table Saw Blades You Need - FineWoodworking
Old Craftsman Table saw 113.298761
Old Craftsman Table saw 113.298761

Mechanical Failures and Repair Options for Stuck Blade Elevation

Once you have ruled out the lock knob and cleaned the gears, the next step is to diagnose a mechanical failure. The behavior of the handwheel gives you important clues. If the handwheel spins freely but the blade does not move, the handwheel is probably not connected to the elevation shaft. If the handwheel will not turn at all, something is jammed, bent, or stripped inside the trunnion assembly.

Many Craftsman table saws are repairable with basic hand tools, a parts diagram, and some patience. Take clear photos before you disassemble anything, and keep screws and small parts in labeled bags. Identify your model number, which is usually on a plate on the back or side of the saw. With that number, you can often find an exploded view and order replacement parts online or through aftermarket suppliers.

AD

Loose or Stripped Handwheel, Set Screw, or Key

The elevation handwheel attaches to the elevation shaft with a set screw, a Woodruff key, a roll pin, or a splined connection. If the set screw loosens, the handwheel can turn without rotating the shaft. If the key or pin falls out, you may feel the handwheel spin freely with no resistance. If the shaft splines are stripped, the handwheel will slip under load and eventually stop raising the blade altogether.

a man using a table saw to cut wood with the words 10 tips table saw setup for optimal performance
a man using a table saw to cut wood with the words 10 tips table saw setup for optimal performance
How to Replace a Craftsman Table Saw Blade
How to Replace a Craftsman Table Saw Blade
Intelligent saw machine
Intelligent saw machine
1972 Craftsman project, Opinions Welcome
1972 Craftsman project, Opinions Welcome

Remove the handwheel and inspect the connection. Tighten the set screw against the flat spot on the shaft, and use a thread locker if it keeps loosening. Replace a missing key or roll pin with the exact size from your parts diagram. If the shaft or handwheel splines are badly worn, replace both parts as a set. This is usually an affordable repair and much easier than replacing the entire trunnion assembly.

Worn Worm Gear, Trunnion Teeth, or Bent Elevation Rod

The worm gear on the handwheel shaft meshes with a gear on the trunnion. If the teeth are chipped, worn, or missing, the blade will not raise smoothly, or it may not raise at all. You may also hear a grinding or clicking sound when you turn the handwheel. Metal shavings or metallic-looking grease around the gear teeth are a strong sign of internal damage.

AD

Replacing a worm gear or trunnion gear is more involved, but it is still a realistic DIY repair on many Craftsman saws. Some models allow you to adjust gear engagement by loosening the trunnion bolts and repositioning the mechanism. Set the backlash so the gears mesh without binding, then retighten the bolts. If the trunnion casting is cracked or the elevation rod is bent, replacement is usually the best option. For discontinued models, check used parts listings, woodworking forums, and aftermarket suppliers before giving up on the saw.

A smooth-raising blade starts with a clean gear train and a released lock knob. Before you spend money on a new saw, spend twenty minutes with a vacuum, a flashlight, and a dry lubricant under the table. If you find a stripped gear or a broken trunnion, source the part and keep your Craftsman cutting. Your next project is waiting, and a table saw that raises its blade on command is worth the effort to repair.

AD