1979 vw bus won't start selinoid

1979 VW Bus Won't Start Selinoid? Here's How to Fix It Fast

By Brian Hernandez
AD

If your 1979 VW Bus won't start and you have narrowed the fault to the solenoid—often misspelled as "selinoid"—you are not alone. These air-cooled Bay Window buses are legendary for their charm, but their aging electrical systems can make a simple turn of the key feel like a guessing game. The starter solenoid is the small cylindrical relay mounted on top of the starter motor, and it takes the low-current signal from your ignition switch and uses it to send a heavy jolt of battery power to the starter motor. When it fails, you might hear a single loud click, a rapid chatter, or nothing at all.

Before you order a new starter or start cutting wires, it helps to understand what the solenoid actually does and how the rest of the starting circuit supports it. A no-start condition on a 1979 Bus can come from a weak battery, corroded cables, a bad ground strap, a tired ignition switch, or a worn starter bushing. The solenoid is often the messenger, not always the culprit. This guide walks you through the most likely causes, the tests that separate a bad solenoid from a bad connection, and the practical fixes that get your Bus cranking again.

Understanding the 1979 VW Bus Starting Circuit

The starting system in a 1979 Volkswagen Bus is simple in concept but fussy in practice. Battery power travels through thick cables to the starter, while a smaller wire from the ignition switch tells the solenoid when to engage. The solenoid then does two jobs: it pushes the starter drive gear into mesh with the flywheel, and it closes a heavy internal contact that sends full battery current to the starter motor. If either job fails, the engine will not crank, even if the battery is fully charged.

AD
1979 VW Bus - Page 2
1979 VW Bus - Page 2
1979 Westfalia Berlin 2L for sale
1979 Westfalia Berlin 2L for sale
an old vw bus parked in front of a building
an old vw bus parked in front of a building

On most 1979 Buses, the battery lives in the engine bay, and the starter is tucked underneath the vehicle where it bolts to the transmission bell housing. That location exposes the starter and solenoid to heat, oil, road grime, and decades of vibration. The result is often a solenoid that works fine when cold but refuses to engage when hot, or a trigger wire that looks connected but cannot carry enough current to pull in the solenoid. Knowing the circuit path helps you test in the right order.

What the Solenoid Does When You Turn the Key

When you turn the ignition key to the start position, current flows through the red/black trigger wire to terminal 50 on the solenoid. Inside the solenoid, two windings—pull-in and hold-in—create a magnetic field that yanks a plunger forward. That plunger does double duty: it shoves the starter pinion gear toward the flywheel and bridges the main battery contacts inside the solenoid. Once those contacts close, the starter motor receives direct battery voltage and begins to spin the engine.

an old vw bus parked in front of a white fence and tree lined area
an old vw bus parked in front of a white fence and tree lined area
the vw bus is parked on the side of the road with its roof open
the vw bus is parked on the side of the road with its roof open
Reviving Your VW Van: Benefits Of A Rebuilt 3-Speed 090 Transmission
Reviving Your VW Van: Benefits Of A Rebuilt 3-Speed 090 Transmission

This is why a failing solenoid can produce such confusing symptoms. You may hear a solid click as the plunger moves, but the engine still will not crank because the internal contacts are burned or pitted. You may hear a rapid clicking sound as the solenoid engages and disengages repeatedly due to low voltage. Or you may hear nothing at all because the trigger circuit, ground path, or solenoid winding has failed completely. Each sound points to a different part of the diagnosis.

Symptoms That Point to a Bad Solenoid

The classic sign of a solenoid problem is a single, loud click followed by silence. That click means the solenoid is at least trying to engage, but the starter motor is not getting the current it needs. Another common symptom is a rapid machine-gun chatter when you turn the key, which usually indicates a weak battery or bad connection rather than a failed solenoid. If the engine cranks slowly and then stops, the solenoid may be closing, but the battery or cables cannot supply enough amperage.

AD

Heat-related no-starts are especially telling on a 1979 Bus. If the engine starts fine when cold but refuses to crank after a long drive, the solenoid may have worn internal contacts that expand with heat. Tapping the starter with a wrench or hammer handle sometimes brings it back to life temporarily, but that is a roadside trick, not a repair. A solenoid that requires tapping is living on borrowed time and should be replaced or rebuilt.

an old vw bus parked in front of a garage
an old vw bus parked in front of a garage
Vintage RV: 1979 VW Microbus/T2 Camper Van
Vintage RV: 1979 VW Microbus/T2 Camper Van
1979 VW Bus Camper Westfalia For Sale in Fremont, MI
1979 VW Bus Camper Westfalia For Sale in Fremont, MI
Bay Window Bus - View topic - Value of my 1979 VW Bus Bay Window California Emissions Auto
Bay Window Bus - View topic - Value of my 1979 VW Bus Bay Window California Emissions Auto
an orange and white vw bus parked in the woods with a tent on top
an orange and white vw bus parked in the woods with a tent on top
an old blue and white van parked in front of a building with cherry blossoms on the tree
an old blue and white van parked in front of a building with cherry blossoms on the tree

Step-by-Step Diagnosis for a No-Start 1979 VW Bus

Diagnosing a no-start condition requires patience and a few basic tools: a digital multimeter, a test light, a remote starter switch, and safety gear. Park the Bus on level ground, set the parking brake, and chock the wheels. Because you will be working around the starter and battery, disconnect the negative battery cable before removing any major components. Never crawl under a vehicle that is supported only by a jack; use sturdy jack stands on a solid surface.

Start with the battery because it is the easiest component to test and the most common source of no-start complaints. A battery can read 12.6 volts at rest and still fail under load, so a load test or conductance test is essential. Clean and tighten both battery terminals, then inspect the cables for swelling, corrosion, or frayed strands. From there, move methodically toward the solenoid, testing voltage at each connection instead of guessing and replacing parts.

AD

Check Battery, Cables, and Grounds Before Blaming the Solenoid

A weak battery or bad ground can mimic a failed solenoid almost perfectly. Set your multimeter to DC volts and measure the battery across the terminals. A healthy, fully charged battery should read about 12.6 volts with the engine off. While a helper turns the key to start, watch the voltage; if it drops below 9.6 volts, the battery is weak or the starter is drawing excessive current. If the voltage stays high but the engine does not crank, the problem is likely in the control circuit or solenoid.

Classic Volkswagen Cars for Sale | VW Classics
Classic Volkswagen Cars for Sale | VW Classics
an old blue vw bus parked in a parking lot next to a body of water
an old blue vw bus parked in a parking lot next to a body of water
an old vw bus is parked in a parking garage with yellow lines on the floor
an old vw bus is parked in a parking garage with yellow lines on the floor
an old van is parked in the grass
an old van is parked in the grass

Next, perform voltage drop tests on the positive and negative cables. Connect the meter between the battery negative post and the starter case while cranking; you should see less than 0.2 volts. A higher reading means the ground path is resistance-heavy. On a 1979 Bus, the transmission-to-frame ground strap and the battery-to-body ground are frequent culprits. Remove them, clean the metal contact points, and reinstall them tightly. Corroded grounds can cause a solenoid to click weakly or not at all.

Test the Ignition Switch, Trigger Wire, and Starter Replacement Options

If the battery and grounds check out, test the trigger wire at the solenoid. Unplug the red/black wire from terminal 50 and connect a multimeter or test light between the wire and a good ground. Have a helper turn the key to start. You should see battery voltage, or at least within 1 volt of battery voltage. If voltage is low or missing, the ignition switch, wiring, or neutral safety switch on automatic models is interrupting the signal. Old ignition switches often develop high resistance, especially after decades of use.

AD

A common permanent fix for 1979 Bus starting problems is adding a starter relay. This relay uses the original trigger wire to energize a new, short circuit directly from the battery to the solenoid, bypassing the voltage drop in the old ignition switch and wiring. If the solenoid still fails to engage when supplied with good voltage and a solid ground, the solenoid itself is likely bad. You can remove the starter and bench-test the solenoid, but on a vehicle this old, replacing the entire starter-solenoid assembly is usually the most reliable path. Choose a quality rebuilt or new unit, and inspect the starter bushing in the transmission while you have it apart.

With a methodical approach, your 1979 VW Bus no-start problem becomes less mysterious and more manageable. The solenoid may be the final link in the chain, but the battery, cables, grounds, and ignition switch all deserve a close look before you spend money on parts. Once you restore a clean, low-resistance path from the key to the starter, that familiar air-cooled crank will return, and your Bus will be ready for the next adventure instead of another afternoon in the driveway.

AD