Craftsman Router Lift: The Ultimate Precision Upgrade for Your Router Table
A Craftsman router lift is one of those upgrades that seems optional until you use one. Instead of crouching beneath the table and fiddling with a plunge base or fixed-base adjustment ring, you turn a crank or hex key above the table and watch the bit rise or fall in precise increments. For anyone who owns a Craftsman router and a router table, that convenience can transform the way you set up joints, profiles, and grooves.
The catch is that Craftsman has produced many routers over the years, and not every lift is a direct fit. Motor diameter, base mounting pattern, plunge versus fixed base, and table plate dimensions all matter. This guide walks through what a Craftsman router lift does, how to match one to your router, and how to install and maintain it so your table stays accurate.
What a Craftsman Router Lift Actually Does
At its core, a router lift is a carriage and adjustment mechanism that mounts below a router table. The router motor clamps into the carriage, and the carriage moves up and down on guides or rails. Instead of adjusting the router itself, you adjust the lift. Most models use a crank handle, hex key, or removable handle that engages a lead screw. Some also allow above-table bit changes, which is a major safety and convenience benefit.
A lift also adds repeatability. Once you find a depth for a particular cutter, you can record the setting and return to it later. That is difficult with many stock router bases, especially older Craftsman plunge routers with coarse depth stops. The lift gives you fine control, usually measured in thousandths of an inch per turn or per graduation.
Above-Table Adjustment and Repeatability
Above-table adjustment is the headline feature. You can raise the bit, lower it, and lock it without reaching into the cabinet. On many lifts, the crank or hex socket sits above the table surface or just below a removable insert. This makes micro-adjustments practical when you are sneaking up on a perfect fit for a dado, rabbet, or cope-and-stick joint.
Repeatability comes from a stable screw and a solid lock. If the carriage has backlash or the lock flexes, your setting can drift. Look for a lift with a robust lead screw, smooth bearings, and a locking mechanism that secures the carriage without shifting it. A good lift lets you return to the same height days later and get the same cut.
Compatibility With Craftsman Router Models
Compatibility is where Craftsman owners need to do homework. Craftsman routers range from older aluminum-body fixed-base models to modern plunge and combo kits. A lift that accepts a Porter-Cable 690 or Bosch 1617 may not accept a Craftsman motor without an adapter or different carriage clamps. The critical measurement is the motor body diameter, not the base diameter.
If you are searching for a Craftsman 17543 router lift or a lift for a similar model, start by measuring the cylindrical motor housing with calipers. Then check the lift manufacturer’s fit chart for that diameter and mounting style. Some lifts use universal clamps that handle a range of motors, while others require a specific adapter. When in doubt, contact the lift maker before buying.
Choosing, Installing, and Maintaining a Craftsman Router Lift
Once you know your router can fit a lift, the next step is choosing the right model for your table and workflow. Plate size, insert ring compatibility, travel, locking style, and dust collection all affect how well the lift works in a Craftsman router table. A lift is a long-term investment, so it is worth matching it to the kind of routing you do most.
Installation is straightforward on most lifts, but details matter. The plate must sit flush with the table, the carriage must clamp the motor securely, and the lift must move without binding. After installation, calibration and routine maintenance keep the mechanism accurate. The following sections cover the specs and steps that make the biggest difference.
Plate Size, Insert Rings, and Table Cutout
Router lift plates come in a few common sizes, and your table cutout must match. Many aftermarket lifts use a plate around 8-1/4 by 11-3/4 inches or 9-1/4 by 11-3/4 inches, but dimensions vary. If you are retrofitting a Craftsman router table, measure the existing opening and the recess depth before ordering. A plate that is too small will not cover the cutout; one that is too large may require a new tabletop.
Insert rings are the removable discs that sit inside the plate opening around the bit. They reduce the gap between the bit and the plate, which supports the workpiece and reduces tearout. A good lift accepts a range of rings, including zero-clearance rings you can make yourself. Check that rings seat flush and stay put; a loose ring can catch an edge and ruin a cut.
Lift Mechanism, Travel, and Locking
Most router lifts use a lead screw or jack screw to move the carriage. The thread pitch determines how much the bit moves per turn. A finer thread gives more precise adjustment but slower travel; a coarser thread moves faster but can be less delicate. Rack-and-pinion designs exist, but for fine woodworking, a good screw-driven lift is usually preferred.
Travel matters if you use long bits or raise panels. A lift with three or four inches of travel covers most router table work, but check the usable range after the motor is mounted. Locking is equally important. A lock that clamps the carriage firmly prevents the bit from creeping during a cut. Some lifts lock from above the table, which is convenient when the router is buried in a cabinet.
Step-by-Step Installation Basics
Begin by unplugging the router. Remove the base or plunge mechanism according to the manufacturer’s instructions, leaving the bare motor and any required mounting collar. Clean the motor housing so the carriage clamps can grip evenly. Set the lift plate upside down on a workbench and attach the carriage following the lift instructions. Do not fully tighten the clamps until the motor is seated.
Lower the motor and carriage into the lift from the top or bottom, depending on the design. Center the motor in the opening and tighten the clamps in small increments, alternating sides so the motor stays straight. Place the plate in the table cutout and check it with a straightedge. Adjust the leveling set screws until the plate is flush with the table surface, then lock the lift and check that the bit is perpendicular to the table.
Calibration, Maintenance, and Dust Control
Calibrate the depth scale after installation. Raise the bit until it just touches the table or a setup block, then set the scale or note the reference mark. Use a dial indicator or calipers to verify movement per turn if precision matters. Keep a notebook or label tape on the table for settings you use often, such as a 1/4-inch dado or a 3/8-inch roundover.
Maintenance is simple but not optional. Vacuum or blow out dust from the screw and guides after heavy use. Apply a dry lubricant such as PTFE if the manufacturer recommends it; oil can attract dust and gum up the works. Check the mounting screws and leveling set screws periodically. Avoid over-tightening the carriage clamps, which can distort the motor housing or make adjustment stiff.
A router lift can turn a Craftsman router table from a basic bench tool into a precise workstation. The key is to measure your motor, match the plate to your table, and choose a mechanism you can adjust comfortably. If you already own a Craftsman router, start with the fit chart and a pair of calipers; if you are buying new, bring your router specs to the decision. With the right lift in place, every depth change becomes quicker, safer, and far more repeatable, leaving you more time to focus on the wood instead of the hardware.