craftsman router plunge base

Craftsman Router Plunge Base: Ultimate Guide for Precision Routing

By Joshua Anderson
AD

If you own an older Craftsman router, you already know the motor is the heart of the tool, but the base is what determines what you can actually build with it. The Craftsman router plunge base is the accessory that transforms a straightforward fixed-base trimmer into a machine capable of cutting mortises, stopped grooves, inlay pockets, and any other cut that requires the bit to enter and exit the workpiece from above. Without one, a whole category of joinery and detail work simply stays out of reach.

Plunge bases show up most often as part of Craftsman combo kits, and they are frequently the component that gets lost, damaged, or separated from its motor over decades of shop use. Understanding how the base works, which routers it fits, and how to set it up correctly means the difference between fighting the tool on every cut and getting clean, repeatable results that rival far more expensive equipment.

Understanding the Craftsman Router Plunge Base

At its core, a plunge base is a carriage. The router motor clamps into a cylindrical bore, and that bore rides up and down on two spring-loaded steel columns. A plunge lock lever on the side of the housing lets you freeze the motor at any point in its travel, which is the entire reason the design exists. Instead of tilting the whole router and hoping the bit bites smoothly, you set the tool flat on the workpiece, start the motor, and lower it straight down into the wood.

AD
WEN Plunge Base Kit for Compact Trim Routers one_size | 20610-PB
WEN Plunge Base Kit for Compact Trim Routers one_size | 20610-PB
Router base plates for Craftsman compact palm routers (V20 Max)
Router base plates for Craftsman compact palm routers (V20 Max)
Craftsman V20 (CMCW400B) Palm/Trim Router Table Plate
Craftsman V20 (CMCW400B) Palm/Trim Router Table Plate

The base also carries the depth-control hardware: a threaded rod, a graduated depth scale, a rotating turret with two or three adjustable stops, and a sub-base plate that rides across the surface of the material. Those parts work together to make depth predictable. On many Craftsman units, a small knurled micro-adjustment knob lets you dial in a depth change in fractions of a millimeter without loosening the lock lever, which is a feature that becomes valuable the moment you start fitting hinges or routing hinge mortises.

How a Plunge Base Differs From a Fixed Base

A fixed base holds the motor at a single, locked height relative to the sub-base. You adjust that height with a ring or a rack-and-pinion mechanism, tighten it down, and then you must tilt the router to begin a cut in the middle of a board. That tilting motion is awkward, and on hardwoods it can cause the bit to grab and the router to kick. A plunge base solves this by letting the bit descend vertically along a controlled path while both hands stay on the handles.

10" Square Acrylic Base Plate for Ryobi 2 HP Plunge Router - Guide Bushing Base Plate
10" Square Acrylic Base Plate for Ryobi 2 HP Plunge Router - Guide Bushing Base Plate
Double Handle Acrylic Router Base - fits Craftsman 20V Max Router ( CMCW400)
Double Handle Acrylic Router Base - fits Craftsman 20V Max Router ( CMCW400)
8″ Acrylic Router Base Plate for Skil RT1322 Plunge Router - Wide Cut Base Plate
8″ Acrylic Router Base Plate for Skil RT1322 Plunge Router - Wide Cut Base Plate

In practice, this changes your workholding requirements as well. Fixed-base routing often pushes you toward routing edges and running full-length grooves from the end of a board, because starting mid-panel is risky. With a plunge base, you can drop the bit into the middle of a wide panel with confidence, which makes stopped dadoes, flutes, and decorative inlays genuinely practical. Many woodworkers keep both bases for the same motor and swap them depending on the operation.

Which Craftsman Routers Accept a Plunge Base

Craftsman sold routers in three broad configurations: fixed base only, plunge base only, and combo kits that included both bases with a single motor. Combo kits from the 1990s and 2000s, such as the 12-amp 320.27683, shipped with a motor that popped out of one base and into the other, and those motors remain the most common candidates for a replacement or spare plunge base today. Plunge-only models from the 315 series and similar production runs used the same basic architecture.

AD

Before buying anything, look at the motor housing itself. The model and serial number are stamped on a plate, usually on the side of the aluminum housing near the top or on the plastic cap. You need the exact model number, because the mounting screw pattern and the bore diameter changed between generations. Aftermarket and used-OEM plunge bases appear regularly on auction sites and through parts dealers, and some universal designs use shims or adapter rings to fit a range of motor housings. Measure the outside diameter of your motor housing with calipers and compare it to the published bore size of any base you are considering.

🚨New Tool: Mortise Base🚨Precision Mortising with your Plunge Router
🚨New Tool: Mortise Base🚨Precision Mortising with your Plunge Router
PLUNGE VS. FIXED BASED ROUTERS
PLUNGE VS. FIXED BASED ROUTERS
three different types of plunger routers with the words which is the best heavy duty plunge
three different types of plunger routers with the words which is the best heavy duty plunge
Guide Rail Router Base - Universal - Etsy
Guide Rail Router Base - Universal - Etsy
the craftsman router is on display in this image, it's red and silver
the craftsman router is on display in this image, it's red and silver
Router Improvement - Add-on
Router Improvement - Add-on

Getting the Most From Your Plunge Base

Out of the box, most plunge bases are close but not perfect. The sub-base needs to be flat and concentric with the bit, the columns need to move without slop or binding, and the depth stops need to be accurate enough to repeat a cut ten times in a row. Spending twenty minutes on setup pays for itself on the very first project, especially when you are cutting mortises where a few thousandths of an inch matters for a tight-fitting tenon.

Dust collection is the other thing that separates a pleasant routing session from a choking cloud of chips. Plunge bases inherently trap debris because the motor sits directly over the cutting area, and Craftsman bases rarely came with effective dust ports from the factory. A shop vacuum hose taped or clamped near the sub-base opening, or a simple aftermarket dust shroud, keeps the cut line visible and keeps chips from being recut into the workpiece surface.

AD

Dialing In Depth Stops and the Turret

The turret on a plunge base is a rotating disc with two or three machine screws of different heights. Each screw acts as a hard stop for the depth rod, so you can set three distinct depths and rotate between them without touching the rod. To set it up, plunge the motor until the bit just kisses the workpiece surface, lock the plunge, and zero the depth rod against the highest turret screw. Then adjust each screw for the successive depths you want.

Digital Plunge Router | Popular Woodworking
Digital Plunge Router | Popular Woodworking
FullFit Pro™ DeWalt DW618 Router Plunge Base (DW6182) - 10x10 Inch Sub-Base Plate
FullFit Pro™ DeWalt DW618 Router Plunge Base (DW6182) - 10x10 Inch Sub-Base Plate

Consider a 3/4-inch-deep mortise in a hardwood leg. Rather than hogging out the full depth in one pass, set the turret screws to roughly 1/4 inch, 1/2 inch, and 3/4 inch. Run the first pass across the whole mortise, rotate to the next stop, run the second pass, then rotate again for the final cut. The bit stays cooler, the finish is cleaner, and the router is far less likely to chatter. Keep a scrap block set to a known thickness nearby as a quick sanity check before you commit the cut to your finished stock.

Maintenance, Safety, and Bit Selection

Plunge columns collect fine dust, and fine dust mixed with old lubricant turns into a gritty paste that wears the bores. Wipe the columns with a dry rag after each session and apply a light coat of dry-film lubricant rather than oil, since oil attracts more dust. Check the plunge lock lever tension periodically, and verify that the sub-base sits flat against a known-flat surface such as a cast iron table saw top. A sub-base with a slight dish will telegraph into every cut as a varying depth.

AD

Safety habits matter just as much as maintenance. Unplug the router before changing bits, keep the bit diameter within the speed range recommended for your motor, and use bits designed for plunging. Straight bits with a center-cutting geometry, spiral upcut bits, and mortising bits all handle vertical entry well, while a bit with a bearing pilot and no center cut will burn and grab. Take shallow passes, keep both hands on the handles during the plunge and the lock, and wear eye and hearing protection every single time, because these tools are loud, fast, and unforgiving.

If your Craftsman motor is still running strong, a properly set up plunge base is one of the cheapest ways to expand what that tool can do, and tracking down the correct base is usually a matter of reading the model plate and doing a little measuring. Dig that router out of the bottom of the cabinet, note the numbers on the housing, and start hunting for the base that matches. A weekend of setup and a few test cuts on scrap will tell you everything you need to know about whether your old Craftsman is ready to earn its place on the bench again.

AD