#8 drill bit size

The #8 Drill Bit Size Guide: Charts, Conversions, and Uses

By Matthew Wilson
AD

If you have ever stared at a drill index and wondered what the tiny stamp "#8" actually means, you are not alone. The #8 drill bit size is one of those measurements that looks simple until you realize it has nothing to do with an 8mm bit or a #8 screw. It belongs to the numbered wire-gauge drill bit system, a set of sizes used for precision work in metal, wood, plastic, and composite materials.

Knowing the exact #8 drill bit size helps you avoid oversized holes, stripped threads, and wobbly screws. This guide breaks down the decimal and metric equivalents, explains where a #8 bit fits in the drill index, and shows you how to choose and use one for common projects.

What Exactly Is the #8 Drill Bit Size?

In the numbered drill bit system, a #8 drill bit has a diameter of 0.1990 inches. In metric terms, that converts to approximately 5.05 millimeters. It is a wire-gauge bit, not a fractional-inch bit, so you will usually find it in a numbered drill index rather than a standard set of 1/16-inch increments.

AD
Drill Bit Sizes Chart With Fractional and Letter Sizes
Drill Bit Sizes Chart With Fractional and Letter Sizes
there are many different types of screws in this display case with the numbers on each side
there are many different types of screws in this display case with the numbers on each side
the instruction sheet for how to use an irwin drill gauge on a sewing machine
the instruction sheet for how to use an irwin drill gauge on a sewing machine

The #8 bit sits in a useful middle ground. It is slightly larger than a 5mm bit, which measures 0.1969 inches, and slightly smaller than a 13/64-inch bit, which measures 0.2031 inches. That tiny difference matters when you need a snug fit for a specific screw, pin, or tap.

Decimal, Fractional, and Metric Equivalents

The most precise way to describe a #8 drill bit is 0.1990 inches. Rounded for shop use, that is 0.199 inches, or about 5.05 mm. If you are comparing it to fractional bits, 13/64 inch is very close at 0.2031 inches, while 5mm is just under it at 0.1969 inches.

a close up of a yellow and black machine with numbers on the front, side and back
a close up of a yellow and black machine with numbers on the front, side and back
the drill tap size formula is shown in three different positions
the drill tap size formula is shown in three different positions
an app showing different types of drilling tools
an app showing different types of drilling tools

Because drill bit manufacturing tolerances vary, one brand's #8 bit may measure a few thousandths of an inch differently from another. For general drilling, that variation is rarely a problem. For precision tapping or close-tolerance assembly, always measure the bit with calipers or test it in scrap material before committing to the final hole.

#8 Drill Bit vs. 8mm and #8 Screw Sizes

An 8mm drill bit is not the same as a #8 drill bit. An 8mm bit measures 0.3150 inches, which is much larger than 0.1990 inches. The confusion is understandable because the number 8 appears in both labels, but one refers to a metric diameter and the other refers to a wire-gauge size.

AD

A #8 screw is also different. A #8 screw has a major diameter of roughly 0.164 inches, or about 4.17 mm. The #8 drill bit is larger than the screw body, so it is not a standard pilot-hole bit for a #8 screw. It can work as a clearance bit for some #10 screws or as a specialty bit for other hardware.

the different types of drill bits
the different types of drill bits
the back cover of an instruction manual for electric tap drill sizes and equals
the back cover of an instruction manual for electric tap drill sizes and equals
Drill Bit Size Chart in Inches, mm, cm With Guide
Drill Bit Size Chart in Inches, mm, cm With Guide
the table size chart for drill sizes is shown in red and black, with an arrow pointing
the table size chart for drill sizes is shown in red and black, with an arrow pointing
What Is the Size of a 29 Drill Bit? (0.1360" Guide)
What Is the Size of a 29 Drill Bit? (0.1360" Guide)
How Big Is a 7/32 Drill Bit Exact Size Explained
How Big Is a 7/32 Drill Bit Exact Size Explained

Common Uses for a #8 Drill Bit

The #8 drill bit is a handy in-between size for drilling clearance holes, pilot holes, and light metal work. Because it falls between common metric and fractional sizes, it often becomes the go-to bit when a 5mm hole is too tight and a 13/64-inch hole feels too loose.

You will often find #8 bits in automotive, electrical, and general fabrication work. They are especially useful when installing hardware that requires a precise fit, such as machine screws, roll pins, and small bolts. Keeping one in your drill index can save you a trip to the hardware store.

AD

Pilot Holes and Clearance Holes

For a #8 wood screw, the pilot hole is usually much smaller than a #8 drill bit. In softwood, a common pilot size is 1/8 inch, while hardwood often calls for 7/64 inch. Those smaller holes allow the screw threads to bite into the wood without splitting it.

Drill Tap Size Chart A Complete Guide
Drill Tap Size Chart A Complete Guide
DEWALT Drill Bit Set, 3-Flats Shank,14-Piece, 135 Degree Split Point👍❤
DEWALT Drill Bit Set, 3-Flats Shank,14-Piece, 135 Degree Split Point👍❤
Drill Bit Sizes Every Woodworking Beginner Should Know
Drill Bit Sizes Every Woodworking Beginner Should Know
7 Methods for Drill Bit Size Selection | Infographics Archive
7 Methods for Drill Bit Size Selection | Infographics Archive

A #8 drill bit can serve as a clearance hole for certain #10 screws. Since a #10 screw has a major diameter around 0.190 inches, a 0.199-inch hole gives it just enough room to pass through without excessive slop. Always check the specific screw standard and material before drilling a visible or structural hole.

Tapping and Metalworking Applications

In metalworking, a #8 drill bit is close to the standard tap drill for a 1/4-20 thread, but it is not the official size. The standard tap drill for 1/4-20 is a #7 bit, which measures 0.201 inches. A #8 bit is only 0.002 inches smaller, so it may work in softer materials, but it can cause excessive torque or tap breakage in harder metals.

AD

For an 8-32 machine screw tap, the standard tap drill is a #29 bit, which measures 0.136 inches. A #8 drill bit is far too large for that task. Use the correct tap drill chart for the thread size, material, and desired thread engagement rather than forcing a nearby bit to do the job.

How to Choose and Use a #8 Drill Bit

Choosing a #8 drill bit depends on the material you are drilling, the coating on the bit, the shank type, and how precise the hole needs to be. A bit that works beautifully in pine may dull quickly in stainless steel, while a bit designed for metal may tear out wood fibers if used incorrectly.

High-speed steel is the baseline for general-purpose drilling. Cobalt bits handle harder metals and higher temperatures. Titanium nitride and black oxide coatings improve wear resistance and chip evacuation, but they do not make a soft bit suitable for hardened steel.

Material, Coating, and Bit Quality

For wood, a brad-point #8 bit can create a clean entry hole and reduce splintering. For metal, a split-point #8 bit helps the drill start without wandering. For plastic, a sharp bit with a gentle feed rate prevents cracking and melting.

Cheap drill bits are often undersized, poorly ground, or made from low-grade steel. A quality #8 bit holds its edge longer and drills a more accurate hole. If you use the bit often, buy a spare or two so you are not stuck with a dull bit in the middle of a project.

Drill Speed, Feed, and Lubrication

When drilling metal with a #8 bit, use a cutting fluid or lubricant and run the drill at a moderate speed. Apply steady pressure and avoid letting the bit spin without cutting, which creates heat and dulls the edge. Clear chips frequently, especially in deep holes.

For wood, you can run the drill faster and feed steadily. For plastic, slow the speed and reduce pressure to prevent melting. A drill press or portable drill guide improves accuracy, particularly when you need the hole to be perfectly perpendicular to the surface.

Keep a #8 drill bit on hand for those odd jobs where a 5mm bit is just a hair too small and a 13/64-inch bit feels loose. Check your specific screw or tap chart before drilling, and let the material guide your speed and pressure. A few practice holes in scrap will tell you more than any label, and that small investment of time usually pays off in cleaner, stronger results.

AD