51/64 Drill Bit Guide: Sizes, Uses, and Best Picks for Your Project
A 51/64 drill bit is one of those fractional sizes that rarely gets top billing in a drill index, yet it solves a very specific problem. At 0.796875 inches, or about 20.24 millimeters, it sits exactly between the more common 25/32 and 13/16 sizes. That narrow window makes it valuable when a 25/32 hole is too tight and a 13/16 hole is too loose.
You will not find a 51/64 bit in every basic set, but machinists, fabricators, and serious DIYers keep one on hand for clearance holes, 3/4-inch fasteners, 20 mm metric hardware, and occasional threading work. The sections below cover its exact dimensions, common applications, and how to choose and run this bit without damaging the workpiece or the tool.
Understanding the 51/64 Drill Bit Size
Fractional drill bits are measured in 64ths of an inch, and 51/64 simply means 51 of those 64 divisions. When converted to decimal, 51 divided by 64 equals 0.796875. That places it precisely one 64th larger than 25/32, which is 50/64 or 0.78125, and one 64th smaller than 13/16, which is 52/64 or 0.8125.
This midpoint position is the reason the size exists in practical tooling. Many assemblies need a hole that is slightly larger than the nominal fastener but not so large that parts shift out of alignment. A 51/64 bit provides that middle ground, especially when working with inch-based bolts and metric hardware that comes close to 20 millimeters.
Decimal and Metric Equivalents
The exact decimal equivalent of a 51/64 drill bit is 0.796875 inches. In metric terms, multiplying by 25.4 gives 20.240625 millimeters. Depending on the manufacturer, you may see it labeled as 20.24 mm, 20.25 mm, or simply 51/64 inch. It is not a letter-size or wire-gauge drill bit, so you will not find it under designations like “Z” or “#10.”
For comparison, a 20 mm drill bit measures 0.7874 inches, which is about 0.0095 inch smaller than 51/64. That small difference matters when you need a bolt, pin, or shaft to slide through without hammering. In woodworking, a 51/64 bit can also serve as a slightly loose 20 mm hole for shelf pins or dowels, though a true 20 mm brad-point bit is usually the better choice for furniture-grade joinery.
How It Compares to Nearby Sizes
The nearest common fractional sizes are 25/32 (0.78125), 51/64 (0.796875), and 13/16 (0.8125). Each step is 1/64 inch, or 0.015625 inch. That means 51/64 is exactly halfway between 25/32 and 13/16. In many workshops, 25/32 is used as a close clearance hole for a 3/4-inch bolt, while 13/16 is used as a normal clearance hole.
If a 3/4-inch bolt binds in a 25/32 hole after paint or rust, a 51/64 bit opens the hole just enough to restore a sliding fit. If a 13/16 hole feels too sloppy for a precision assembly, 51/64 reduces the play without going all the way back to the tighter size. For metric fasteners, a 20 mm bolt measures 0.7874 inch, so a 51/64 hole gives roughly 0.24 mm of clearance, which is a close fit suitable for alignment-critical work.
Practical Applications and Selection
Because 51/64 is an intermediate size, it rarely appears in general-purpose drill bit sets. You usually buy it individually when a project calls for a hole between two standard sizes. Common uses include clearance holes for 3/4-inch bolts and pins, passage holes for 20 mm metric fasteners, and occasional tapping operations where the correct tap drill is unavailable.
Selecting the right 51/64 bit depends on the material, the tool holding it, and the accuracy required. Metalworkers generally choose high-speed steel or cobalt with a 135-degree split point. Woodworkers prefer brad-point or auger bits for clean edges. Masonry requires a carbide-tipped bit, while plastics demand sharp flutes and slow speeds to prevent melting.
Clearance Holes for Bolts and Fasteners
For a 3/4-inch bolt, standard clearance holes are often listed as 25/32 for a close fit, 13/16 for a normal fit, and 7/8 for a loose fit. A 51/64 hole falls between the close and normal categories, making it a tight-normal clearance. This is ideal when you want the bolt to pass through easily but still need the connected parts to stay aligned during assembly.
In metric work, a 20 mm bolt or pin has a nominal diameter of 0.7874 inch. A 51/64 hole at 0.796875 inch provides about 0.0095 inch, or 0.24 mm, of clearance. That is tighter than the standard 21 mm or 22 mm clearance holes used for M20 hardware, so it works well for jigs, fixtures, and machinery where excessive play would cause misalignment. Examples include hitch pins, suspension brackets, agricultural implements, and anchor bolts in steel plates.
Tap Drill and Threading Applications
A 51/64 bit is sometimes used as an alternative tap drill for a 7/8-9 thread. The recommended tap drill for 7/8-9 is usually 49/64, which produces approximately 75 percent thread engagement. A 51/64 hole is larger, so it produces roughly 54 percent thread engagement. That lower percentage can be acceptable in aluminum, brass, plastic, or when repairing damaged threads, but it is not ideal for high-strength steel applications.
If you use a 51/64 bit for tapping 7/8-9, run the tap at slow speed, use plenty of cutting fluid, and reverse the tap frequently to break chips. The reduced thread engagement means the fastener will have less load-bearing capacity, so reserve this approach for low-stress assemblies or temporary repairs. For critical joints, buy the correct 49/64 tap drill instead of forcing a 51/64 bit to do the job.
Drill Bit Materials and Drilling Techniques
High-speed steel is the most common material for a 51/64 bit and handles wood, plastic, and mild steel well. Cobalt bits, such as M35 or M42, resist heat better and are the better choice for stainless steel, titanium, and hardened alloys. Black oxide coating provides mild lubricity and corrosion resistance, while titanium nitride coating improves wear resistance for repeated use. Carbide bits last longer in abrasive materials but can chip if used in a hand drill.
Speed and feed matter more with a large bit like 51/64 because it removes a lot of material quickly. For mild steel, a surface speed of about 100 feet per minute translates to roughly 480 RPM. For aluminum, you can run closer to 1,400 RPM. For wood, 1,000 to 1,500 RPM is typical. Use cutting fluid on metal, peck drill deep holes to clear chips, and always clamp the workpiece. A pilot hole of 1/4 or 3/8 inch reduces the load on the drill and improves accuracy.
Buying Guide and Storage
Because 51/64 is not included in most 29-piece fractional sets, you will usually buy it as a single bit. Look for a reduced 1/2-inch shank if you plan to use it in a standard hand drill or drill press chuck. If you have a 3/4-inch chuck, a full-size shank is stronger and runs truer. Brands such as Irwin, Bosch, DeWalt, Milwaukee, Drill America, Cleveland, and Chicago-Latrobe offer reliable options, but check the point angle, coating, and intended material before buying.
For occasional home use, a high-speed steel 51/64 reduced-shank bit is sufficient. For production metalwork, invest in cobalt or carbide. Store the bit in a drill index or protective sleeve to prevent nicks, and apply a light coat of oil to prevent rust. If you sharpen your own bits, use a drill bit gauge to verify that the diameter remains 0.796875 inch, since oversharpening can quickly turn a precision clearance hole into an oversized one.
When a project calls for a hole that is just a hair larger than 25/32 but not as wide as 13/16, a 51/64 drill bit is the quiet problem-solver. Keep one in your toolbox, match it to the material and chuck you are using, and it will earn its place on jobs where standard sizes simply fall short.