Wire Size Amperage Chart: Easy AWG Ampacity Guide for Safe Wiring
Choosing the right electrical wire is not a matter of guesswork. A wire size amperage chart gives you a quick reference for how much current a conductor can safely carry without overheating, damaging insulation, or creating a fire risk.
Whether you are adding a workshop outlet, running a feeder to a subpanel, or sizing a circuit for an EV charger, the relationship between wire gauge and amperage determines whether the installation will be reliable and code-compliant.
Understanding Wire Size and Amperage Ratings
Wire size is expressed in American Wire Gauge, or AWG. The numbers work backward from what many people expect: a smaller AWG number means a thicker conductor with more metal and a higher current-carrying capacity.
Amperage is the measure of electrical current flow. Every conductor has a safe limit, known as ampacity, based on its size, metal type, insulation temperature rating, and the conditions where it is installed.
What Wire Gauge Really Means
AWG is a standardized system that describes the diameter and cross-sectional area of a conductor. A 14 AWG copper wire is thinner than a 12 AWG wire, and a 12 AWG wire is thinner than 10 AWG.
Because thicker wire has lower resistance, it can carry more current with less heat and less voltage drop. That is why large appliances, subpanels, and long runs often require a lower gauge number than a simple lighting circuit.
Why Ampacity Charts Matter for Safety
An undersized wire can overheat when it carries more current than its insulation can tolerate. The heat may damage the conductor, degrade the insulation, and eventually cause a short circuit or fire.
A wire size amperage chart helps you match the conductor to the load and the breaker. It also helps you avoid the opposite mistake: using oversized wire that is expensive, difficult to bend, and hard to terminate properly.
How to Read and Apply a Wire Size Amperage Chart
Most charts list wire gauge in the first column and ampacity values in later columns. The ampacity values are usually separated by insulation temperature rating, such as 60°C, 75°C, and 90°C.
You may also see separate columns for copper and aluminum. Copper has higher conductivity, so it carries more current for the same size. Aluminum is lighter and less expensive, but it requires larger conductors and terminations rated for aluminum.
Key Columns, Temperature Ratings, and Materials
The 60°C column is commonly used for older wiring, certain types of NM-B cable, and terminations that are not rated for higher temperatures. The 75°C column is typical for many modern terminals and THHN conductors in conduit.
The 90°C column often applies to the wire insulation itself, but the final ampacity is usually limited by the termination rating. A 90°C wire connected to a 75°C breaker terminal cannot be used at its full 90°C ampacity.
- 14 AWG copper: 15 amps at 60°C, 20 amps at 75°C, 25 amps at 90°C
- 12 AWG copper: 20 amps at 60°C, 25 amps at 75°C, 30 amps at 90°C
- 10 AWG copper: 30 amps at 60°C, 35 amps at 75°C, 40 amps at 90°C
- 8 AWG copper: 40 amps at 60°C, 50 amps at 75°C, 55 amps at 90°C
- 6 AWG copper: 55 amps at 60°C, 65 amps at 75°C, 75 amps at 90°C
- 4 AWG copper: 70 amps at 60°C, 85 amps at 75°C, 95 amps at 90°C
- 2 AWG copper: 95 amps at 60°C, 115 amps at 75°C, 130 amps at 90°C
- 1/0 AWG copper: 125 amps at 60°C, 150 amps at 75°C, 170 amps at 90°C
Notice how much ampacity changes with temperature rating. A 6 AWG copper wire may be listed at 55 amps in a 60°C application but 75 amps in a 90°C application. The weak link is often the breaker, outlet, or splice, not the copper itself.
Aluminum conductors follow a similar pattern but with lower ampacity for the same gauge. For example, a 2/0 aluminum conductor may be rated around 135 amps to 150 amps depending on temperature, while a 2/0 copper conductor is typically rated higher.
Matching Breakers, Loads, and Voltage Drop
The circuit breaker protects the wire, not the appliance. A 14 AWG copper conductor on a 15-amp breaker is a standard match for lighting and general outlets. A 12 AWG copper conductor on a 20-amp breaker is common for kitchen, bathroom, and garage circuits.
For larger loads, a 10 AWG copper wire often pairs with a 30-amp breaker, an 8 AWG copper wire with a 40-amp breaker, and a 6 AWG copper wire with a 50-amp or 60-amp breaker, depending on the wire type and load.
Voltage drop becomes significant as distance increases. A 120-volt circuit that runs 150 feet may need a larger conductor than the amperage chart alone suggests, because the voltage at the far end must stay within an acceptable range.
For 240-volt circuits, voltage drop is less severe per amp for the same wire size, but long feeders to detached garages, barns, or outbuildings still deserve a voltage drop calculation. Sizing up one or two gauges is often cheaper than replacing a failed motor or dimming lights.
Keep a current wire size amperage chart with your project notes, and verify every conductor against the actual load, insulation rating, and distance before you cut, crimp, or connect. That habit turns a confusing table into a dependable safety check for every circuit you build or repair.