winterize sprinkler system diy

Winterize Sprinkler System DIY: Easy Step-by-Step Guide to Protect Your Pipes

By Laura Lewis
AD

Water is one of the few things on your property that can destroy thousands of dollars worth of equipment simply by sitting still. When overnight temperatures dip below freezing, any water left inside your irrigation lines expands with enough force to split PVC, crack polyethylene tubing, and shatter brass valves. A do-it-yourself winterization routine takes a Saturday afternoon and can prevent a springtime repair bill that runs into four figures.

Whether you run a single-zone drip setup or a six-zone rotor system, the process follows the same logic: remove the water, protect the components that stay above ground, and shut the system down so nothing tries to run while it is dry. Below is a practical, step-by-step guide to winterizing a sprinkler system yourself, including the pressure limits and safety habits that keep you from blowing a line apart in the process.

Why Winterizing Beats Repairing Your Sprinkler System

Water expands by roughly nine percent when it turns to ice, and that expansion does not care whether it is inside a copper pipe or a cheap plastic elbow. Irrigation laterals are typically buried only six to twelve inches deep, which sits above the frost line in most of the country. That means the soil around your pipes can freeze solid, squeezing the lines from the outside while ice pushes outward from the inside. The result is usually a split in the weakest fitting rather than a clean break you can spot right away.

AD
DIY Sprinkler Blowout To Winterize Sprinkler System - Making Manzanita
DIY Sprinkler Blowout To Winterize Sprinkler System - Making Manzanita
How to Winterize a Sprinkler System
How to Winterize a Sprinkler System
How To Properly Winterize Your Sprinkler System For Accurate Maintenance
How To Properly Winterize Your Sprinkler System For Accurate Maintenance

Compare the two outcomes. A professional winterization visit generally costs somewhere between $75 and $200 depending on where you live and how many zones you have. Repairing freeze damage often means excavating a trench, replacing a manifold, swapping out solenoid valves, and possibly replacing a backflow preventer, which alone can run $150 to $400 installed. Add the cost of water pouring out of a cracked line while you are at work in April, and the math gets ugly fast.

What Actually Freezes Inside a Sprinkler System

Most homeowners picture the long lateral lines as the main risk, but the real trouble spots are the small, tightly confined spaces where water has nowhere to go. Zone valves and their solenoid ports, the manifold body, the backflow assembly, check valves under each sprinkler head, swing joint risers, and the pump housing on systems fed by a pond or well all trap water. Brass and thin-wall plastic fittings fail first because they cannot flex as ice expands.

How To: Winterize Your Sprinkler System
How To: Winterize Your Sprinkler System
Why You Need to Winterize Your Sprinkler System
Why You Need to Winterize Your Sprinkler System
DIY Easy Sprinkler blowout winterization
DIY Easy Sprinkler blowout winterization

Backflow preventers deserve special attention. A reduced pressure zone assembly or pressure vacuum breaker sits above ground by code, fully exposed to wind and hard freezes. The internal check discs and relief ports hold small amounts of water that will crack the body if you skip the drain-down step. Even a "frost-free" hydrant feeding the system can trap water in the valve body if a hose or adapter is left attached.

Tools and Supplies You Will Need for the Job

The single most important piece of equipment is an air compressor with enough cubic feet per minute output to move water, not just pressurize the line. A small pancake compressor built for nail guns will run nonstop, overheat, and leave water sitting in your laterals. You also want a proper quick-connect or threaded adapter that mates your compressor hose to the blow-out port, system drain, or a hose bib tee on the mainline.

AD

Beyond the compressor, gather these items before you start so you are not jogging back to the garage with the system pressurized:

How to Winterize Your Sprinkler System
How to Winterize Your Sprinkler System
How To Winterize Your Sprinklers (Sprinkler Blow Out With Air!)
How To Winterize Your Sprinklers (Sprinkler Blow Out With Air!)
How to Winterize Your Sprinkler System | A DIY Guide
How to Winterize Your Sprinkler System | A DIY Guide
Winterize Outdoor Plumbing & Sprinklers Before the First Freeze
Winterize Outdoor Plumbing & Sprinklers Before the First Freeze
Winterize Your Sprinkler System [how to Blow-Out Drain Wilkins Zurn 720A]
Winterize Your Sprinkler System [how to Blow-Out Drain Wilkins Zurn 720A]
Winterize Sprinkler System Simple Steps
Winterize Sprinkler System Simple Steps
  • Safety glasses and work gloves, since compressed air can throw debris and water
  • Adjustable wrench, channel locks, and a set of valve keys
  • Foam pipe insulation sleeves, zip ties, and exterior-grade tape
  • Optional heat cable for backflow assemblies in harsh climates
  • Your controller manual, which lists zone order and run times
  • Towels or a small bucket for the water that will spray out of the connection point

How to Blow Out a Sprinkler System With an Air Compressor

The blow-out method uses high-volume air to chase water out through the sprinkler heads instead of pushing it deeper into the soil. Air enters at the highest connection point, usually the backflow or a blow-out tee on the mainline, and travels through the manifold and one zone at a time until nothing but a fine mist leaves the nozzles. It is fast, effective, and the standard practice in cold climates.

Timing matters as much as technique. Winterize after your last watering of the season but before the first hard freeze, ideally when daytime temperatures are still above 40 degrees Fahrenheit. Working in freezing weather risks cracking fittings during handling and makes the water in the lines harder to evacuate. If you have already had a light frost, drain the main supply immediately and finish the blow-out on the next mild afternoon.

AD

Pressure, CFM, and Compressor Settings That Keep Pipes Intact

Volume moves water; pressure breaks pipes. Most irrigation manufacturers cap recommended blow-out pressure at 50 PSI for rigid PVC and 30 to 40 PSI for polyethylene laterals, though many techs run 20 to 50 PSI with very high airflow. Work with a regulator, crack the valve slowly, and remember that the pressure reading at the tank is not the pressure at the far end of a zone. Never use a compressor rated under 10 CFM for even a modest system.

Turning On Sprinkler System After Winter
Turning On Sprinkler System After Winter
Sprinkler Blowout - Cabin DIY
Sprinkler Blowout - Cabin DIY
how to winterize your sprinkler system
how to winterize your sprinkler system
Winterizing Sprinklers - How to blow out sprinklers - Her Tool Belt
Winterizing Sprinklers - How to blow out sprinklers - Her Tool Belt

Use this as a rough starting point, and always defer to your system manufacturer's published limits:

System SizeMinimum Air VolumeTypical Equipment
Up to 4 short zones10 to 15 CFMLarge electric, 20 to 30 gallon tank
5 to 8 average zones15 to 20 CFMPortable gas compressor
8+ zones or long runs20 to 25+ CFMTow-behind commercial unit

Cycling Zones Safely Until the Lines Run Dry

Start by shutting off the irrigation water supply at the main valve or the dedicated backflow shutoff. Open the blow-out port, connect your adapter and hose, and put on your safety glasses before you open any valve. Activate the shortest zone first through the controller or by turning the solenoid a quarter turn, then let air flow until the heads pop up and the spray turns from a solid stream to a sputtering mist. Shut that zone down and move to the next one.

AD

A few habits keep this step from turning expensive. Never let air run through a single zone for more than about two minutes at a stretch, and never leave the compressor running with every zone valve closed, which deadheads the pump and can damage both the compressor and the manifold. Once you have cycled every zone, repeat the entire sequence a second time. The first pass clears the bulk of the water; the second catches the pockets that settled back into low spots.

Gravity Draining, Insulation, and Cold-Weather Protection

Not every homeowner needs a compressor. If you live in a region with only occasional light frosts, or your system was installed with manual drain valves at the low points of every zone, gravity may do the work for you. Open the valves, open the manifold, and let the lines empty into the soil or a nearby drain. Water follows the slope, and a properly pitched system will shed most of its contents in a few minutes.

That said, gravity draining is only as good as the installation. Lines that sag between fittings, zones that run uphill, and drip tubing with emitters every twelve inches all hold water that refuses to cooperate. If your climate regularly sees temperatures in the teens, pair gravity draining with a blow-out or budget for a service call. Insulation alone will not save a line that is full of water.

Manual Drain Valves Versus Automatic Drain Valves

Manual drain valves are the reliable option. They sit in valve boxes at the lowest point of each zone, and you open them with a screwdriver or a small key. Let each zone drain fully, then leave the valves partially open through the winter so any residual water has somewhere to expand. Automatic drain valves work on a different principle: they open when line pressure drops below roughly five PSI, which happens when the system shuts down.

Automatic drains sound convenient, but they have two weaknesses. First, they only release water until the spring-loaded seat closes, which often leaves a small amount trapped. Second, they clog with grit and mineral deposits and stop sealing, so you get a wet spot in the yard all summer. Treat them as a supplement to a blow-out, not a replacement.

Protecting the Backflow Preventer, Controller, and Faucets

The backflow assembly is your most exposed component and needs its own routine. Shut the upstream and downstream ball valves, open the test cocks and drain ports, and let the body empty completely. If your assembly is the removable type, take it off and store it indoors for the winter. If it stays outside, wrap it with foam insulation and secure the wrap with zip ties so wind cannot peel it off, and consider a thermostatically controlled heat cable in the coldest zones.

Inside the garage, set the controller to the off position and unplug the transformer. Leaving a schedule active means the timer can fire a valve while the system is dry, and dry-firing solenoids burn out quickly. Disconnect every hose from every spigot, including the one feeding the irrigation main, drain the drip and micro-irrigation tubing, and empty any fertilizer injector or rain barrel. If you have a booster pump or a well pump feeding the system, kill power to it at the breaker as well.

Once the water is out and the above-ground hardware is wrapped, mark the date on your calendar and stop thinking about it until the soil thaws. When spring arrives, reopen the drain valves, reinstall the backflow, restore power, and run each zone for a minute or two while you walk the yard looking for geysers, soggy patches, or heads that refuse to pop. Catching a cracked fitting before the first real watering of the season is a ten-minute job, and it beats discovering the leak with a shovel in July.

AD