What Goes Under Metal Roofing? The Ultimate Guide to Underlayment and Insulation
What goes under metal roofing matters just as much as the metal panels themselves. While the visible standing seam or corrugated profile takes the weather on the outside, the hidden assembly beneath it controls condensation, leakage, noise, thermal movement, and long-term durability. A metal roof is a system, not a single sheet, and the layers directly below the panels determine whether that system performs for decades or creates expensive callbacks.
Homeowners, builders, and roofing contractors often ask about underlayment, decking, insulation, and ventilation because metal roofing behaves differently from asphalt shingles. Metal expands and contracts, can be installed over open purlins or solid decking, and may reach higher surface temperatures. Understanding each component helps you specify the right stack-up for your climate, building design, and budget.
The Structural Substrate Under Metal Roofing
Before any underlayment or metal panel is installed, the roof needs a stable substrate that carries wind uplift, snow load, foot traffic during installation, and fastener pull-out. That substrate can be solid sheathing, spaced purlins, or a combination, depending on the metal roofing profile and the building's structural design. The choice affects not only strength but also how moisture and heat move through the assembly.
In residential reroofs, the existing deck is often inspected and repaired before metal is installed. In new construction, the framing and decking are engineered for the specific panel system. Skipping substrate repairs or using the wrong thickness can void manufacturer warranties and cause oil-canning, fastener back-out, or premature sealant failure.
Roof Decking Materials
Solid roof decking for metal roofing is typically plywood or oriented strand board (OSB), usually installed at a minimum thickness specified by local code and the panel manufacturer. Plywood offers good screw-holding capacity and handles incidental moisture reasonably well, while OSB is dimensionally consistent and cost-effective. Both must be dry, clean, and properly fastened to the rafters or trusses before underlayment goes down.
Some metal roof systems require a minimum deck thickness, such as 7/16-inch or 1/2-inch sheathing, and may require ring-shank nails or screws at specific intervals. Gaps between panels are often left for expansion, and damaged or delaminated sections must be replaced. If the deck is uneven, installers may use a self-adhered membrane or a separation layer to prevent the metal from telegraphing board joints.
Purlins, Battens, and Open Framing
Not every metal roof goes over solid sheathing. In agricultural, commercial, and some residential applications, metal panels are fastened to purlins or battens—horizontal framing members spaced according to the panel's load span. This creates an air cavity beneath the metal, which can help with ventilation and thermal separation, but it also changes what underlayment and weather barrier are appropriate.
With open purlins, a high-temperature underlayment or a synthetic roof underlayment may be installed over the purlins to control condensation and wind-driven rain, depending on the design. In other assemblies, rigid insulation or a radiant barrier is placed between the purlins and the metal. The key is to follow the panel manufacturer's installation manual, because open-framed systems often require different closure details, fasteners, and moisture management than solid-deck roofs.
Underlayment, Insulation, and Moisture Control Layers
Once the substrate is sound, the next question is what goes directly under the metal roofing panels. The answer usually includes one or more of the following: a roof underlayment, an ice-and-water shield at vulnerable areas, a high-temperature membrane, insulation, and a vapor retarder or air barrier. Each layer has a distinct job, and they must work together rather than trap moisture or create condensation.
Metal roofing is highly conductive, so warm interior air that reaches the underside of a cold panel can condense into water. That is why the underlayment and insulation strategy must address both liquid water intrusion and vapor movement. In cold climates, the goal is to keep the roof deck warm and dry; in hot, humid climates, the goal is often to control inward vapor drive and reduce heat gain.
Synthetic Underlayment vs. Felt and Ice-and-Water Shield
Synthetic underlayment is a woven or nonwoven polymer sheet that resists tearing, holds up to UV exposure during installation, and provides a secondary water-shedding layer beneath metal panels. It is lighter than asphalt-saturated felt and generally more resistant to wrinkling, which helps prevent the metal from showing surface irregularities. Many manufacturers require a specific synthetic underlayment for their metal roofing warranties.
Asphalt felt—often called #15 or #30 felt—is still used in some markets, but it can tear, buckle, and absorb moisture. Ice-and-water shield, a self-adhered rubberized membrane, is typically installed along eaves, valleys, ridges, sidewalls, and around penetrations. For metal roofs, a high-temperature version may be necessary because standard peel-and-stick membranes can soften or bleed under the heat of a dark metal panel. The correct combination depends on roof slope, climate, and panel finish.
Insulation, Vapor Barriers, and Ventilation
Insulation under metal roofing can take several forms: rigid foam boards above the deck, batt insulation below the deck, spray foam on the underside of the roof, or a combination. Rigid insulation is often installed over the roof deck to create a thermal break and reduce condensation on the metal. Because metal is an excellent conductor, a continuous layer of insulation helps prevent thermal bridging through rafters and purlins.
Vapor barriers and ventilation work together to manage moisture. In cold climates, a vapor retarder is usually placed on the warm side of the insulation, while ventilation channels or an airspace allow the roof deck to dry. In hot climates, a radiant barrier or reflective insulation can reduce heat transfer into the attic. Ridge vents, soffit vents, and eave/ridge baffles keep air moving under the roof deck, which is especially important when metal roofing is installed over a solid deck with minimal natural drying potential.
Choosing what goes under metal roofing is a decision that should be made with your climate, building code, roof pitch, and manufacturer instructions in mind. A metal roof can last decades, but only when the hidden layers are selected and installed correctly. Talk with a qualified roofing contractor or building designer about the full assembly before the first panel is fastened, and you will be far more likely to enjoy a quiet, dry, energy-efficient roof for the long haul.