Truck Bed Cattle Feeders: Durable, Portable Feeding Solutions for Livestock
A truck bed cattle feeder turns a standard pickup into a mobile feeding rig, letting one person cover hundreds of head without hauling a trailer or wrestling with bags of cake by hand. Ranchers running pairs on scattered pastures, stocker operators pushing gains on wheat, and feedlot crews topping off bunks all lean on some version of this setup to move feed where it needs to go — fast, accurately, and with far less labor than the old pitchfork-and-bucket routine.
But the category covers a wide spread of equipment. A gravity-flow cake feeder bolted into a short bed is a very different machine from a hydraulic auger system with a spinner that throws cubes thirty feet past the fence line. Understanding how each design works, what it costs, and where it actually earns its keep is the difference between a tool that saves you two hours every day and one that sits in the corner of the shop collecting dust.
Why Ranchers Mount Feeders in the Truck Bed
The economics of feeding cattle have always been tied to labor. Every additional trip, every extra gate, and every minute spent scooping feed out of a sack adds up across a 200-day feeding cycle. A truck bed cattle feeder compresses all of that into a single pass: you drive the fence line or the feed alley, pull a lever or hit a switch, and feed flows out at a controlled rate while you keep both hands on the wheel.
There is also a practical advantage in portability. A feeder mounted in the bed can go anywhere the truck goes — across a creek, down a muddy two-track, into a pen that a feed wagon would never fit through. That flexibility matters most on operations with fragmented pastures or where temporary fencing shifts every few weeks with the grazing rotation.
Labor and Time Savings
A well-set-up pickup feeder lets one person do the work that used to take two or three. On a typical 300-head cow herd, feeding cake from the bed of a truck takes roughly half the time of loading and pulling a trailer, and you never have to unhook anything. The driver stays in the cab, which means cold mornings, blowing snow, and 100-degree afternoons all become considerably more tolerable.
The savings compound when you feed every day. Shaving 45 minutes off a daily chore adds up to more than 250 hours a year — the equivalent of six full work weeks. Put a dollar figure on that labor and most feeders pay for themselves within a single feeding season, sometimes two depending on capacity and features.
Feed Accuracy and Reduced Waste
Hand-feeding is notoriously inconsistent. One day the cows get three pounds of cubes, the next day five, and by the end of the month nobody is quite sure what the average intake actually was. A calibrated truck bed feeder delivers a repeatable volume per second of auger run or per gate opening, which makes it possible to hit a target supplementation rate with real precision.
That consistency translates directly into feed efficiency. Overfeeding protein and energy is expensive, and underfeeding stretches the calving interval and drags down weaning weights. Getting the rate right also cuts waste — cubes scattered into mud or trampled into manure are money on the ground, and a spinner or controlled drop tube keeps the feed in a tighter window where cattle can actually clean it up.
Types of Truck Bed Cattle Feeders
The market breaks into a handful of recognizable designs, each built around a different method of moving feed from the hopper to the ground. Gravity units are simple and cheap, auger systems are versatile, and spinner or blower setups are built for speed and distance. Most buyers end up choosing based on herd size, feed type, and how often the truck doubles as a work vehicle during the rest of the year.
It is also worth thinking about the truck itself. A feeder that adds 1,500 pounds of feed plus 400 pounds of steel changes how a half-ton pickup handles, brakes, and wears its rear springs. Matching the feeder to the truck — and to the loads you routinely carry — is just as important as matching it to the cattle.
Gravity and Drop-Gate Feeders
Gravity feeders rely on nothing more than slope and a metering gate. Feed sits in a sloped hopper and flows down to an adjustable opening, where the driver controls the release with a lever or cable running into the cab. There is no motor, no hydraulic line, and almost nothing to break, which makes them the go-to choice for ranchers who value simplicity above all else.
The trade-off is control. Gravity units work best with free-flowing feed such as range cubes, pelleted supplements, or whole grain, and they can bridge or plug when the product is damp or dusty. They also tend to be the least precise at low feed rates, so they suit broad supplementation rather than tight, measured rations.
Auger-Driven and Hydraulic Systems
Auger feeders use a flighted screw inside a tube to pull feed from the hopper and carry it to a discharge point, usually at the rear or side of the bed. Because the auger moves feed mechanically rather than by gravity, it handles a wider range of ingredients — ground mixes, cracked corn, and blended rations that would choke a simple drop gate.
Hydraulic versions tap into the truck's power steering or a dedicated PTO-driven pump, giving the operator variable speed control from the cab. That variable speed is the key advantage: you can creep along at two miles per hour and lay down a light strip of feed, or run faster and spread the same ration over a longer stretch of fence line without changing the auger setting.
Spinner and Blower Attachments
Spinner attachments mount at the discharge end and use a rotating disc to broadcast feed in a wide arc. They are designed for situations where you cannot or should not drive inside the pen — feeding across a fence, over a ditch, or into a pasture where opening a gate would scatter the herd. A good spinner can throw cubes twenty to thirty feet with reasonable accuracy.
Blower systems take that idea further by using a high-volume fan to push feed through a tube, sometimes reaching forty feet or more. They shine in large, open pastures and in feedlots where cattle are spread wide, but they demand more horsepower, cost significantly more, and tend to be finicky about feed moisture and particle size. For most cow-calf operations, a spinner is the practical ceiling.
Choosing, Installing, and Maintaining a Feeder
Once you have narrowed down the type, the decision comes down to capacity, mounting method, and build quality. Capacity determines how many head you can feed per load and how often you have to make a trip back to the commodity shed. Mounting determines whether the feeder is a permanent fixture or something you can pull out in ten minutes when you need the bed for hay or fencing supplies.
Build quality is where cheap units separate from good ones. Powder-coated steel holds up in humid climates, stainless hardware resists corrosion from salt and mineral mixes, and a hopper with proper slope and cleanout access will save you hours of chipping out caked feed. Those details rarely show up in a spec sheet, but they show up every single morning when you are trying to get fed and get moving.
Matching Capacity to Herd Size
A general rule of thumb is that a feeder holding 1,000 pounds of cubes will feed roughly 200 head at a five-pound rate, which covers a single day for a mid-sized herd. Doubling that capacity to a ton means fewer refill trips, but it also means the truck is carrying an extra 1,000 pounds of tongue weight and the suspension needs to handle it.
For smaller operations running fifty to a hundred head, a 500- to 750-pound hopper is usually plenty and keeps the truck usable for other chores. Large operations often run two trucks with smaller hoppers rather than one truck with an oversized one, because the ability to feed two separate pastures simultaneously frequently beats the marginal savings from a single bigger load.
Mounting, Wiring, and Safety
Most truck bed cattle feeders bolt to the bed floor using the factory tie-down points or a set of drilled and reinforced mounting plates. Bumper-mount and gooseneck-over-the-ball designs exist too, but they limit what else you can haul and complicate trailer hookups. Whatever the mount, use grade-8 hardware, backing plates underneath the bed, and a torque check after the first few loaded trips.
Wiring deserves just as much attention. Run power through a fused circuit with proper gauge wire, protect it in loom where it passes through metal, and add a quick-disconnect so you can pull the feeder without leaving live leads dangling. Keep the hopper covered on gravel roads, never exceed the truck's payload rating, and remember that a loaded feeder raises the center of gravity — corner slower than you think you need to.
Routine Maintenance and Winter Care
Cleanout is the single most important maintenance habit. Feed residue left in a hopper absorbs moisture, hardens, and eventually bridges over the auger or gate, turning a five-minute chore into an hour of chipping with a pry bar. At the end of each feeding cycle, run the auger empty and sweep out the corners with a stiff brush.
Lubricate bearings and grease fittings on the schedule the manufacturer specifies, inspect auger flights for wear and bending, and check gate cables and linkages for stretch or fraying. In cold climates, keep a spare shear bolt or two in the glovebox and store the feeder under cover when it is not in use — a covered, dry feeder will outlast a weather-beaten one by years.
If you are still feeding out of the back of a pickup with a scoop shovel, the upgrade to a purpose-built truck bed cattle feeder is one of the highest-return investments you can make on a cattle operation. Start by measuring your real daily feed volume, weigh that against what your truck can safely carry, and talk to other producers about which designs have held up on ground like yours. The right setup will quietly pay you back every morning for a decade or more.