sb chevy head casting marks

SB Chevy Head Casting Marks: The Ultimate Guide to Identifying Small Block Chevy Heads

By Rachel Jones
AD

Small Block Chevy head casting marks are the fastest way to identify what you are looking at before you buy, sell, or rebuild a set of cylinder heads. Those raised or stamped numbers under the valve cover can reveal the casting number, date code, chamber size, valve configuration, and even the original application. For anyone building a 283, 327, 350, or 400, knowing how to read SB Chevy head casting marks is not just trivia—it is the difference between a great-flowing set of heads and a pair of crack-prone smog castings.

The challenge is that Chevrolet used dozens of casting numbers over five decades, and not every number tells the whole story. A head can be drilled for accessory holes, milled, rebuilt, or swapped onto an entirely different engine. That is why casting marks should be treated as a starting point, not the final word. With a little patience and the right reference points, you can decode common SBC heads and avoid the most expensive mistakes.

What Small Block Chevy Head Casting Marks Actually Tell You

Casting marks are not one single code. Most SBC heads carry a large casting number, a date code, and foundry or manufacturer marks. The casting number identifies the basic head design, while the date code tells when the head was cast. These marks are usually raised, not stamped, and they are located under the valve cover or near the intake ports.

AD
the instructions for how to make a small block cylinder head identification guide with pictures and text
the instructions for how to make a small block cylinder head identification guide with pictures and text
the instructions for how to build a house
the instructions for how to build a house
Guide to Chevy Small-Block Production Heads - Chevy DIY
Guide to Chevy Small-Block Production Heads - Chevy DIY

The casting number does not always reveal valve size, because the same casting could be machined with different valves. It also does not guarantee the head is original to a particular engine. Rebuilding, decking, and replacement parts can change the final specs. Use casting marks together with measurements and visual checks before you make a decision.

Where to Find Casting Numbers and Date Codes

On most small block Chevy heads, the main casting number sits on top of the head, under the valve cover, between the rocker studs or near the intake port. You may also find a date code nearby, often a combination of numbers and letters. Some heads have a GM logo, a Winter's foundry mark, or a snowflake symbol that can help confirm the source.

Shafiroff, SB2.2 Heads Power Up Gen I SBC
Shafiroff, SB2.2 Heads Power Up Gen I SBC
an engine block is shown with four different holes on the top and one has two large metal
an engine block is shown with four different holes on the top and one has two large metal
Updating The Early Stovebolt
Updating The Early Stovebolt

If the valve cover is still installed, use a mirror and flashlight to peek at the top of the head. A borescope can help on engines still in the car. Clean the area with a wire brush or degreaser, because grease and paint can hide the numbers. Take clear photos from multiple angles before you try to decode them.

Reading the Numbers Without Removing the Head

You can often identify a head without pulling it. Look for the casting number first, then the date code. On many SBC heads, the number is visible from the front or rear once the valve cover is removed. If the head is installed, remove the valve cover and use a small mirror to read the top surface.

AD

Be careful with headers, alternator brackets, and accessory drive parts that can block the view. A phone camera with a flash can capture the number in tight spaces. Once you have the number, compare it against a trusted SBC casting chart, but verify the valve size and chamber volume before buying.

SBC Firing Order and Torque Specs | 350 & others
SBC Firing Order and Torque Specs | 350 & others
Small Block Chevy Identification Guide | Ground Up Motors - SS396.com
Small Block Chevy Identification Guide | Ground Up Motors - SS396.com
Best Sbc Brodix Heads Deals | Dealsan
Best Sbc Brodix Heads Deals | Dealsan
an image of the engine block and valve
an image of the engine block and valve
Big-Block Chevy Cylinder Head Basics
Big-Block Chevy Cylinder Head Basics
Chevy cylinder head Identification - Small block casting numbers
Chevy cylinder head Identification - Small block casting numbers

Popular SBC Head Casting Numbers and Buyer Checks

Certain casting numbers come up again and again in classifieds and swap meets. The 461, 462, 186, and 041 heads are early performance favorites. The 292, 492, 993, 441, 487, 882, and 624 castings are common later-model heads, but many are standard or smog-era pieces rather than high-performance gold. Vortec 906 and 062 heads are popular for modern builds because they flow well, but they require a Vortec-style intake.

A casting number alone does not make a head valuable. Chamber size, valve size, port design, and condition matter more. A rare casting with cracks or worn guides is worth less than a common casting that has been properly rebuilt. Always match the number to the intended use, and check for restamps, decking, and repaired damage before you hand over cash.

AD

Fuelie, Double Hump, and Early Performance Heads

The legendary double hump or fuelie heads include castings such as 461, 462, and 186. They are known for 64cc combustion chambers and good flow for their era. Many came with 1.94-inch intake and 1.50-inch exhaust valves, while some were machined for 2.02/1.60 valves. They were used on high-performance 327 and 350 engines.

Swap Meet Guide To Small-Block Chevy Cylinder Head ID
Swap Meet Guide To Small-Block Chevy Cylinder Head ID
How to Source Chevy Big-Block Cylinder Heads - Chevy DIY
How to Source Chevy Big-Block Cylinder Heads - Chevy DIY
Chevy 409 Mark I Big Block Engine Build - Mighty Fine 409
Chevy 409 Mark I Big Block Engine Build - Mighty Fine 409
Best Sbc Afr Heads Deals | Dealsan
Best Sbc Afr Heads Deals | Dealsan

The 041 casting is another early performance head often grouped with double humps. It can have 64cc chambers and accessory bolt holes, making it easier to swap into later cars. However, age and core shift mean these heads should be pressure-tested and checked for cracks. Original double hump heads can command strong prices, but reproductions and restamps exist, so inspect carefully.

Vortec, LT1, and Late-Model Casting Marks

Vortec small block heads, especially casting numbers 906 and 062, are a favorite budget upgrade. They use a raised intake port and a specific intake manifold bolt pattern, so a standard SBC intake will not fit. They typically have 64cc chambers and 1.94/1.50 valves, and they flow better than most older factory castings. Look for the casting number under the valve cover and confirm the intake bolt pattern.

AD

Later small block and LT1-style heads use different casting marks and centerbolt valve covers. The aluminum 113 casting is a common Corvette L98 head, while other numbers like 083, 128, and 217 show up in later performance applications. These heads may have reverse-flow cooling, different intake angles, or specific accessory provisions. Never assume an LT1 or Vortec head is a direct bolt-on for an older carbureted engine.

Decoding SB Chevy head casting marks is part detective work and part hot-rod common sense. The numbers give you a strong lead, but the real story is in the chambers, ports, valves, and overall condition. Whether you are chasing a set of double humps for a vintage 327 or hunting Vortec heads for a budget 350, take the time to verify every mark and measurement. That extra effort can save you from a mismatched intake, a cracked casting, or a combination that never runs the way you imagined.

AD