rough opening for french doors

Rough Opening for French Doors: Exact Dimensions Made Easy

By Mark Martin
AD

Framing a wall for a new set of French doors is one of those jobs where a half inch of carelessness can cost you an entire weekend. The rough opening is the framed gap in your wall that the door unit slides into, and it has to be sized, squared, plumb, and level before the door ever arrives on site. Get it right and installation becomes a matter of shimming and trimming. Get it wrong and you are pulling nails, cutting out studs, and hoping the drywaller never notices.

French doors raise the stakes because there are two operating leaves, a shared astragal or meeting stile, and often a heavy sill and threshold assembly that all need to sit flat and true. A single prehung door forgives a quarter inch of slop. A pair of doors that must meet in the middle at a consistent gap does not. This guide walks through the numbers, the framing details, and the field checks that keep a French door project moving in the right direction.

Understanding the Rough Opening for French Doors

A rough opening is not the finished opening you see once the trim and casing are installed. It is the raw, framed cavity between the jack studs and beneath the header, measured to the framing lumber itself before any drywall, siding, or trim goes on. The prehung door unit, which includes the door slabs, the jambs, the threshold, and often a brickmold or exterior casing, fits inside that cavity with a small amount of clearance on all sides for shimming and adjustment.

AD
The Trick to Hanging French Doors - Fine Homebuilding
The Trick to Hanging French Doors - Fine Homebuilding
an open door with the words how to calculate a door rough opening on it
an open door with the words how to calculate a door rough opening on it
an open door with parts labeled on it
an open door with parts labeled on it

That clearance is intentional, but it is not generous. Most manufacturers build in roughly a half inch on each side and about an inch and a half to two inches at the top, depending on whether the unit has a sill pan or a fixed threshold. Exceed those tolerances and you lose the ability to plumb the jambs without leaving a visible gap. Come in under them and the unit simply will not fit without force.

What Exactly Is a Rough Opening?

The rough opening is defined by four planes of framing: two jack studs on the sides, a header across the top, and the subfloor or rough sill at the bottom. For an exterior French door, the bottom of the opening is usually the subfloor plus whatever the exterior decking or threshold detail requires. For an interior French door between rooms, the subfloor is the reference point for the finished floor height.

DY Install Out-Swing Double Exterior French Doors - DIY Home Improvement Projects
DY Install Out-Swing Double Exterior French Doors - DIY Home Improvement Projects
the inside of a house being built with wood framing and walls in place for doors
the inside of a house being built with wood framing and walls in place for doors
French or Double Door Installation | EZ-Hang Door
French or Double Door Installation | EZ-Hang Door

Because the rough opening is measured to framing, it is critical to calculate it before the wall is sheathed and finished. Once drywall is hung, the visible opening shrinks by roughly an inch on each side and half an inch at the top, depending on drywall thickness and the jamb width. The rough opening is the number the framer needs; the finished opening is the number the trim carpenter cares about. Mixing the two up is one of the most common framing mistakes on residential job sites.

Why French Doors Demand More Precision Than a Single Door

A single door has one slab and one set of jambs, so minor racking can be corrected by adjusting the hinges or planing a corner. French doors have two slabs plus a meeting stile, and the astragal or T-astragal that seals the gap between them is unforgiving. If the opening is out of square, one door will sit low and the other high, and the meeting stile will bind or show a tapered gap from top to bottom.

AD

Exterior French doors add another variable: water. The threshold and sill pan must slope correctly and drain outward, which means the rough opening has to be flat and level across its full width. A crowned subfloor or a header that is out of level by a quarter inch will tilt the entire unit, and water will find the low corner every time it rains.

How to Frame a Door Rough Opening
How to Frame a Door Rough Opening
Installing Slab French Doors In A Cased Opening The Easy Way -- Part 1
Installing Slab French Doors In A Cased Opening The Easy Way -- Part 1
Installing Exterior French Doors: Prepare the Rough Opening
Installing Exterior French Doors: Prepare the Rough Opening
Interior French Doors
Interior French Doors
Installing Exterior French Doors on a Manufactured Home (Mobile Home)
Installing Exterior French Doors on a Manufactured Home (Mobile Home)
a kitchen with an open glass door leading to the outside area and stone wall behind it
a kitchen with an open glass door leading to the outside area and stone wall behind it

How to Calculate the Correct Rough Opening Size

The starting point is always the manufacturer's specification sheet, which lists the rough opening dimensions for that exact model. No rule of thumb overrides that document. With that said, the general industry formula for a prehung French door pair is straightforward: take the overall unit width and add two inches, then take the overall unit height and add two and a half inches.

The extra width accounts for roughly a half inch of shim space on each side, plus a small allowance for framing irregularities. The extra height covers the head jamb, the shim space above it, and the thickness of the sill or threshold assembly at the bottom. When a unit includes a fixed sidelight or a transom, those components are part of the overall unit size, so they get counted in the calculation rather than added separately.

AD

The Standard Formula and Common Dimensions

For a typical 6 foot 8 inch (80 inch) tall French door pair, the rough opening height lands at 82 1/2 inches. Width depends on how many leaves you have and whether sidelights are included. A 5 foot wide pair, for example, needs a 62 inch rough opening, while a 6 foot wide pair needs 74 inches. Always round to the nearest sixteenth and write the number on the framing itself before you start cutting.

How to Install Double French Doors
How to Install Double French Doors
Installing French Doors for Stylish Room Separation in Your Home
Installing French Doors for Stylish Room Separation in Your Home
an empty living room with no one in it
an empty living room with no one in it
French Door Install
French Door Install

The table below shows rough opening dimensions based on the standard two inch width and two and a half inch height allowance. Verify against your specific product literature before framing.

Door Unit Size Rough Opening Width Rough Opening Height
48" x 80" pair 50" 82 1/2"
60" x 80" pair 62" 82 1/2"
72" x 80" pair 74" 82 1/2"
60" x 96" pair 62" 98 1/2"

Adjustments for Sidelights, Transoms, and Out-Swing Units

Sidelights and transoms are factory-assembled with the door unit, so you simply use the combined width and height printed on the order confirmation. A pair of doors flanked by two 14 inch sidelights, for instance, might have an overall unit width of 88 inches, giving you a 90 inch rough opening. Do not frame the door separately and add the sidelights later; these are engineered as one assembly with shared jambs.

AD

Out-swing French doors are hinged on the exterior face, which changes how the unit sits in the opening but not the basic rough opening math. What does change is the threshold detail and the head flashing sequence, since the doors swing away from the building and the sill is often a lower profile. Interior French doors are usually thinner and lighter, but the two inch by two and a half inch allowance still holds in most cases.

Framing, Measuring, and Verifying Before Installation

Once you have the number, the framing itself has to be built to support it. That means king studs on the outside, jack studs on the inside, and a header sized for the span and the load above it. French doors are heavy, and an exterior pair carries roof or floor loads above, so a doubled 2x10 or 2x12 header is common for typical residential spans, with engineered lumber specified for wider openings.

Equally important is square. Measure the diagonals from corner to corner of the rough opening. If the two measurements differ by more than an eighth of an inch, the opening is racked and needs correction before the door unit goes in. Squaring is far easier to fix while the wall is open than after the siding and drywall are finished.

Framing the Opening: Studs, Headers, and Square

Build the rough opening so the jack studs run continuous from the sole plate to the underside of the header, and double the king studs beside them for rigidity. Cripple studs above the header transfer load to the top plate. If the opening sits on a slab or over a crawlspace, confirm the subfloor is flat and shim or plane as needed, because the threshold will telegraph every hump and dip.

Level the header carefully. A header that slopes an eighth inch over a six foot opening will make the doors swing open or closed on their own, a problem known as self-operating doors. Check plumb on both jack studs with a four foot level at minimum, and verify the opening depth so the jamb will sit flush with the finished wall surface on both sides.

Measuring Twice: Checks That Save Thousands

Before the delivery truck arrives, re-measure the rough opening at three points for width, top, middle, and bottom, and three points for height, left, right, and center. Use the smallest width and the smallest height, because those are the real constraints. Then confirm the diagonal measurements once more and inspect the subfloor for flatness with a straightedge.

Finally, stage the door unit dry, without fasteners or shims, to confirm it clears the opening and that the jambs sit roughly centered. Check that shim space exists at every hinge point, at the strike side, and above the head jamb. If the unit slides in with even gaps and the diagonals are within tolerance, installation will go smoothly. If anything binds, stop and correct the opening rather than forcing the door.

Taking the extra hour to verify dimensions, square, and level before the door unit is uncrated will save you far more time on the back end, when the trim is going up and the weather seal needs to be tight. Measure carefully, frame generously within tolerance, and your French doors will hang true for decades.

AD