Plywood Thickness Chart: Standard Sizes, Measurements, and Conversion Guide
A plywood thickness chart is one of those reference tools that seems almost too basic to matter—until a cabinet door binds, a subfloor flexes, or a trim piece refuses to sit flush. The fractions and millimeter conversions printed on a supplier's spec sheet tell only part of the story. Real plywood moves, sands down, and gets compressed during manufacturing, so the number on the label is rarely the number you measure with a caliper.
That gap between expectation and reality is why builders, cabinetmakers, and DIYers keep a plywood thickness chart close at hand. It helps you choose the right sheet for shelving, underlayment, furniture, and structural sheathing, while also warning you when a nominal size will not match an existing surface. The more you understand the chart, the fewer surprises you will face at the cutting table.
How to Read a Plywood Thickness Chart
Most plywood thickness charts begin with a nominal thickness, such as 1/4 inch, 1/2 inch, or 18 mm. Nominal thickness is the trade name, not a guaranteed measurement. It gives suppliers, designers, and framers a common language for ordering and specifying material. The actual thickness, usually listed beside it, is the dimension you get when you measure the panel with a caliper or micrometer.
A useful chart also notes the standard or grade behind the number. Structural plywood, sanded hardwood plywood, and imported Baltic birch can follow different tolerance rules. For example, North American structural panels often fall under PS 1 or PS 2, while hardwood plywood may reference ANSI/HPVA HP-1. Those standards influence how much variation is allowed, so the same nominal size can feel different depending on the product family.
Nominal vs. Actual Thickness
Nominal thickness is a label, while actual thickness is a physical measurement. A 3/4-inch sheet of sanded plywood commonly measures 23/32 inch, or about 18.3 mm. A 1/2-inch sheet often measures 15/32 inch, roughly 11.9 mm. A 1/4-inch sheet may come in at 7/32 inch, or about 5.5 mm. These differences are small on paper, but they matter when you are fitting drawers, routing grooves, or matching old flooring.
The variation comes from sanding, drying, and pressing. Once veneers are glued and cured, the panel is sanded to a consistent surface, which removes material from both faces. Manufacturers also work within accepted tolerances, so two sheets from different mills may not measure exactly the same. Always measure the batch you plan to use, especially if your project depends on tight joinery.
Why Plywood Thickness Varies by Standard and Manufacturer
Plywood is not a single product. It can be made from softwood or hardwood, with different core constructions, glue lines, and face grades. A structural sheathing panel may be manufactured to prioritize strength and stiffness, while a cabinet-grade panel may be sanded to a finer finish. Those priorities affect final thickness, even when both sheets are sold as the same nominal size.
Moisture content adds another variable. Wood expands and contracts as humidity changes, and a panel stored in a damp warehouse may measure slightly thicker or thinner than one kept in a climate-controlled shop. Manufacturer tolerances, veneer thickness, and the number of plies all play a role. A reliable plywood thickness chart will include these caveats rather than pretending every sheet is identical.
Common Plywood Thicknesses and Their Best Uses
The most common plywood thicknesses in North America are 1/4 inch, 1/2 inch, and 3/4 inch, but many projects call for 3/8 inch, 5/8 inch, or 1-1/8 inch. Metric markets tend to revolve around 3 mm, 6 mm, 9 mm, 12 mm, 15 mm, 18 mm, and 25 mm. The right choice depends on span, load, fastener length, edge support, and the finish you want.
Thinner sheets are flexible and light, making them useful for drawer bottoms, cabinet backs, and veneer skins. Thicker sheets resist bending and carry more weight, so they show up in subfloors, shelving, workbenches, and structural sheathing. A plywood thickness chart helps you compare those options quickly, but the final decision should always consider how the panel will be supported and what will be attached to it.
Imperial Plywood Thickness Chart for North American Projects
In imperial sizing, a typical plywood thickness chart lists nominal sizes from 1/8 inch up to 1-1/8 inch. The 1/8-inch sheet is often used for drawer bottoms, door skins, and craft work. The 1/4-inch sheet is common for cabinet backs, underlayment, and light shelving. The 3/8-inch and 1/2-inch sheets appear in cabinets, wall sheathing, and utility panels. The 5/8-inch and 3/4-inch sheets are mainstays for subfloors, roofing, and furniture, while 1-1/8-inch panels are reserved for heavy-duty flooring and structural applications.
Actual measurements often run slightly under the nominal label. A 3/4-inch panel may measure 23/32 inch, a 5/8-inch panel may measure 19/32 inch, and a 1/2-inch panel may measure 15/32 inch. Those differences can affect hardware alignment, so test-fit before committing to a full cut list. If you are replacing an existing sheet, measure the old panel in several spots and compare it to the chart before buying.
Metric Plywood Thickness Chart for International Specifications
Metric plywood thickness charts usually list 3 mm, 4 mm, 6 mm, 9 mm, 12 mm, 15 mm, 18 mm, 21 mm, 25 mm, and 30 mm. Common project sizes include 6 mm for cabinet backs, 12 mm for drawer boxes and light shelving, and 18 mm for cabinets, furniture, and general construction. The 18 mm sheet is often compared to 3/4 inch, but it is actually about 0.3 mm thinner than a true 3/4-inch panel.
Metric and imperial sizes are not direct swaps. A 12 mm sheet is about 0.7 mm thinner than a 1/2-inch sheet, and a 6 mm sheet is about 0.4 mm thinner than a 1/4-inch sheet. Those gaps can be too large for hardware designed around imperial dimensions, especially in drawer slides and hinges. When working with metric plans, use metric plywood and metric hardware whenever possible to avoid compounding conversion errors.
The smartest approach is to treat any plywood thickness chart as a guide, not a guarantee. Bring your caliper to the supplier, measure the actual panels in the stack, and confirm that the thickness matches your hardware, joinery, and span requirements. A few minutes of verification before you buy can save hours of rework after the first cut.