plane strain vs plane stress

Plane Strain vs Plane Stress: Key Differences, Formulas, and Examples

By Laura Martinez
AD

Every finite element analyst eventually faces a deceptively simple question: should this model use plane stress or plane strain? The answer shapes element choice, boundary conditions, material behavior, and even whether the computed stresses are physically meaningful. Both idealizations reduce a three-dimensional problem to two dimensions, but they do so under opposite assumptions about what happens in the third direction.

Understanding the difference is not academic. A thin bracket loaded in its plane behaves very differently from a long retaining wall or a buried pipeline. Choosing the wrong assumption can underestimate displacement, overpredict stiffness, or hide critical out-of-plane stresses. This article breaks down plane strain vs plane stress, explains the governing assumptions, and shows how to match the right model to real engineering hardware.

The Core Concepts: Plane Stress vs Plane Strain

At their heart, plane stress and plane strain are mathematical idealizations that collapse a 3D continuum into a 2D slice. Engineers rely on them because full 3D simulations are expensive, and many structures have geometries that justify the reduction. The decision hinges on which quantities are assumed zero—not which quantities are simply small or ignored.

AD
Stress vs Strain: Most Students Get This Wrong! ⚠️
Stress vs Strain: Most Students Get This Wrong! ⚠️
a diagram showing the direction of an object moving in opposite directions, with arrows pointing up and down
a diagram showing the direction of an object moving in opposite directions, with arrows pointing up and down
Understanding the Difference Between Stress and Strain
Understanding the Difference Between Stress and Strain

In plane stress, the out-of-plane normal stress is assumed zero. In plane strain, the out-of-plane normal strain is assumed zero. That single inversion drives different stress-strain matrices, different effective stiffness, and different failure predictions. Equilibrium, compatibility, and boundary conditions still apply, but the constitutive law changes the entire response.

What Is Plane Stress?

Plane stress applies to thin flat bodies loaded in their plane. The thickness is much smaller than the in-plane dimensions, and the top and bottom surfaces are free of normal traction. As a result, the out-of-plane normal stress σ_z is taken as zero, and the out-of-plane shear stresses τ_xz and τ_yz are also zero. The in-plane stresses σ_x, σ_y, and τ_xy remain active.

A Rule Based Method to Construct The Mohr’s Circle for Plane Stress
A Rule Based Method to Construct The Mohr’s Circle for Plane Stress
stress vs strain
stress vs strain
Plane Crash
Plane Crash

Although σ_z vanishes, the out-of-plane strain ε_z does not. The material is free to contract or expand through the thickness because of Poisson's ratio. A thin aluminum plate with a central hole under tension is a classic example: the plate thins slightly as it stretches. Aircraft skins, automotive body panels, sheet metal blanks, and thin printed circuit boards are often analyzed with plane stress elements.

What Is Plane Strain?

Plane strain applies to long prismatic bodies with a uniform cross-section and loads that do not vary along the length. Material adjacent to any given cross-section prevents axial expansion or contraction, so the out-of-plane normal strain ε_z is assumed zero. The out-of-plane normal stress σ_z is not zero; it develops because the material wants to strain in that direction but cannot.

AD

Classic examples include a long concrete dam analyzed at mid-length, a tunnel far from its portal, a buried pipeline away from joints, and a strip foundation. In each case, the cross-section deforms in its own plane while the long direction remains essentially fixed. Near free ends or abrupt changes in geometry, the assumption weakens and a 3D analysis becomes more appropriate.

an info sheet describing the different types of aircrafts and how they are used to fly
an info sheet describing the different types of aircrafts and how they are used to fly
Why a Plane Turns the Wrong Way First: Adverse Yaw
Why a Plane Turns the Wrong Way First: Adverse Yaw
Understanding Plane Stress
Understanding Plane Stress
an airplane wing is shown with different colored lines coming out of the plane's wings
an airplane wing is shown with different colored lines coming out of the plane's wings
an airplane taking off from the airport with instructions on how to prepare for take off
an airplane taking off from the airport with instructions on how to prepare for take off
Brutal Plane Crash Simulation Reveals Why The Right Brace Position Could Save Your Life
Brutal Plane Crash Simulation Reveals Why The Right Brace Position Could Save Your Life

Key Differences in Assumptions and Stress-Strain Behavior

The most visible distinction is what happens in the z-direction. Plane stress sets σ_z to zero, while plane strain sets ε_z to zero. This is not just a swapped variable; it changes how the material resists in-plane deformation. Because Poisson's ratio couples the directions, constrained axial strain in plane strain produces a nonzero axial stress and alters the apparent stiffness of the cross-section.

Engineers often compare the two using the full 2D constitutive matrix rather than a single modulus. In plane stress, the out-of-plane freedom softens the in-plane response slightly. In plane strain, the out-of-plane constraint stiffens the response and generates a triaxial stress state. That difference can shift yield onset, change fracture predictions, and affect fatigue life estimates.

AD

Out-of-Plane Stress and Strain

In plane stress, the out-of-plane strain follows ε_z = -(ν/E)(σ_x + σ_y). It is generally nonzero, so the body changes thickness as it carries in-plane load. The out-of-plane stress is zero by assumption. In plane strain, ε_z = 0 and the out-of-plane stress becomes σ_z = ν(σ_x + σ_y) for an isotropic linear elastic material.

Stress and strain
Stress and strain
three different types of aircrafts are shown in this diagram and below the image is an airplane flying over water
three different types of aircrafts are shown in this diagram and below the image is an airplane flying over water
What is Stall? (Why Planes Suddenly Lose Lift)
What is Stall? (Why Planes Suddenly Lose Lift)
What are the Principal Stresses and Principal Planes? - ExtruDesign
What are the Principal Stresses and Principal Planes? - ExtruDesign

That nonzero σ_z matters for failure criteria. Von Mises stress, for example, includes all three normal stresses. A plane strain model can therefore predict yielding earlier than a plane stress model with the same in-plane stress field. Ignoring σ_z in a genuinely plane strain problem can be unsafe, especially in thick sections, soils, and constrained welds where triaxial tension develops.

Hooke's Law and Effective Stiffness

For isotropic plane stress, the in-plane stresses are σ_x = E/(1-ν²) [ε_x + ν ε_y], σ_y = E/(1-ν²) [ε_y + ν ε_x], and τ_xy = G γ_xy, with σ_z = 0. The shear modulus G remains E/[2(1+ν)]. This form is used by plane stress elements that require a thickness input.

AD

For isotropic plane strain, the constitutive law uses different coefficients because ε_z is forced to zero. One common form is σ_x = [E(1-ν)]/[(1+ν)(1-2ν)] [ε_x + (ν/(1-ν)) ε_y], with the analogous expression for σ_y, and σ_z = ν(σ_x + σ_y). For the same in-plane strain field, plane strain generally produces higher in-plane stresses than plane stress because the material cannot relieve Poisson expansion through the thickness.

Selecting the Right Idealization for Real-World Problems

Choosing between plane stress and plane strain starts with geometry and loading, not with convenience. Ask where the structure is thin and free to deform in the third direction, and where it is long and restrained. Also ask what output you need. If out-of-plane stress controls failure, a plane stress model may be inappropriate even if the geometry looks thin.

Boundary conditions are equally important. Plane stress elements need a thickness property and typically assume traction-free faces. Plane strain elements assume zero axial strain and often represent a unit slice of a much longer body. If the real part sits between these extremes, consider generalized plane strain, axisymmetric modeling, or a full 3D solution.

Practical Applications of Plane Stress

Plane stress is the natural choice for thin plates, sheet metal components, aircraft fuselage skins, automotive panels, diaphragms, and thin-walled tanks. It is also common in fracture mechanics for thin specimens, where the through-thickness constraint is low and the stress state near a crack tip is closer to plane stress. The smaller the thickness relative to the in-plane dimensions, the stronger the justification.

Consider a perforated metal strip pulled in tension. A plane stress model with a specified thickness can capture the stress concentration around the hole, the overall elongation, and the reduction in width. If the strip is thin, the predicted thickness contraction is real and harmless. If the same model is used for a very thick plate, however, the actual material near the center will be constrained, and the plane stress result may be unconservative.

Practical Applications of Plane Strain

Plane strain is appropriate for long dams, tunnels, retaining walls, strip footings, pipelines far from end connections, and rolling processes where the deformation zone is long compared with its cross-section. It is also used in soil mechanics for embankments and excavations that extend over a long distance. The analysis captures the cross-sectional response while assuming no axial movement.

Take a concrete gravity dam. At the middle of a long dam, the cross-section carries water pressure, self-weight, and uplift. The surrounding concrete prevents significant axial strain, so a plane strain model gives a realistic σ_z and a more accurate triaxial stress state. Near the abutments or construction joints, the assumption breaks down, and a 3D model or a more localized analysis is needed.

The cleanest way to build judgment is to run a small benchmark problem both ways and compare the out-of-plane quantities, not just the contour plots. Watch how σ_z, ε_z, and von Mises stress change as you vary thickness and axial restraint. That habit will make the next FEA model faster to set up and far harder to misread.

AD