Onkyo TX-NR808 No Sound? Quick Fixes to Restore Audio Fast
When an Onkyo TX-NR808 no sound issue appears, the receiver can look perfectly healthy: the display lights up, input names change, and the menu responds. That contrast between normal operation and total silence often makes owners assume the worst, but the TX-NR808 is a complex A/V receiver with dozens of settings that can interrupt audio before a single watt reaches your speakers. Before you shop for a replacement or schedule a repair, work through the signal path from source to speaker in an organized way.
This guide focuses on the most common causes of no audio on the Onkyo TX-NR808, from simple remote-control mistakes to HDMI board and DSP failures. The goal is not to overwhelm you with theory, but to help you isolate the faulty stage quickly. In many cases, a hidden setting, an incorrect input assignment, or a speaker selector button is the only reason the receiver stays silent.
Start With the Onkyo TX-NR808 Basics Before You Blame the Hardware
Begin by confirming that the receiver is actually trying to play the source you think it is. The TX-NR808 can display an input name such as CBL/SAT, GAME, or BD/DVD while receiving no audio data at all. Check that the correct source device is powered on, not paused, and not muted, and that its own audio output is configured for the connection type in use. A streaming box or cable box may be sending video over HDMI but no audio if its digital audio output is set incorrectly.
Next, verify that the TX-NR808 itself is not muted and that the volume is at a normal listening level. Onkyo receivers also have an Audio Selector or Audio Sel function that can force the receiver to look for audio on a specific input. If that setting is locked to Analog, Optical, or Coaxial while your source is connected by HDMI, the receiver will remain silent even though the video appears fine. Set it back to Auto and retest before moving on to deeper troubleshooting.
Confirm the Correct Input, Source, and Listening Mode
Use the remote to cycle through every listening mode available for the selected input. Modes such as Direct, Pure Audio, Stereo, and Multichannel can behave differently depending on the incoming signal. If the receiver is set to a mode that expects a signal type the source is not sending, you may get silence or only partial audio. Try Stereo first because it is the most forgiving mode for two-channel and downmixed content.
Also check whether the TX-NR808 is receiving a supported audio format. Some older HDMI sources default to bitstream formats that the receiver cannot decode, especially if the source is set to output DTS-HD or Dolby TrueHD over an incompatible path. Switch the source to PCM output temporarily. If PCM produces sound, the issue is likely a format or decoding mismatch rather than a dead amplifier.
Check Speaker A/B, Mute, and Zone 2 Settings
The TX-NR808 has speaker selector options that can turn off the main speaker terminals without any obvious warning on the front display. Press the Speaker A/B button and cycle through A, B, A plus B, and off. If the receiver is set to Speaker B only while your main speakers are connected to the A terminals, you will hear nothing in the main room. Confirm that the correct speaker pair is active for your setup.
Zone 2 and Zone 3 settings can also create confusion, particularly if Powered Zone 2 is enabled and the surround back channels have been reassigned. While Zone 2 normally does not mute the main zone, a mix of speaker selection, volume assignment, and input routing can make it seem as though the receiver has lost all audio. Turn off all secondary zones temporarily, return to the main zone, and test a simple analog or HDMI source with the speaker selector set correctly.
Trace the Audio Path: HDMI, Digital, and Analog Inputs
If the basic settings are correct, the next step is to determine whether the problem affects every input or only some of them. Connect a known-good source directly to the TV with the same HDMI cable to prove that the source and cable work. Then reconnect it to the TX-NR808 and try a different HDMI input. This simple test tells you whether the fault follows the source, the cable, or a specific input on the receiver.
The TX-NR808 routes HDMI audio through its internal HDMI board before sending it to the DSP for processing. Digital coaxial and optical inputs follow a different path, while analog RCA inputs often bypass much of the digital decoding chain. By testing one connection type at a time, you can narrow the Onkyo TX-NR808 no sound problem to a board, a menu setting, or a specific source device instead of guessing blindly.
Troubleshoot HDMI Inputs and Input Assignments
Open the receiver’s Input Assign menu and confirm that each HDMI jack is assigned to the input name you are selecting. It is easy to plug a device into HDMI 3 but leave the receiver expecting it on HDMI 1. Also check that the HDMI input is enabled for audio and not set to pass-through-only behavior. If your TV is handling audio through ARC, make sure ARC is enabled on both the TV and the receiver, and that the correct input is selected for TV audio.
If every HDMI input produces video but no sound, and analog or optical inputs work normally, the HDMI board becomes the prime suspect. The TX-NR808 is known for HDMI board failures caused by heat, aging capacitors, and voltage regulator problems. A failing HDMI board can still pass video while losing audio, or it may cause intermittent sound that disappears after the receiver warms up. In that situation, a firmware update or factory reset rarely restores permanent HDMI audio.
Test Digital Coaxial, Optical, and Analog Connections
Connect the same source to the TX-NR808 using an optical or coaxial cable if the device has that output. Select the matching digital input and set the source to output PCM or standard Dolby Digital rather than a high-definition codec. If sound appears through the digital connection, the receiver’s digital-to-analog conversion and amplifier stages are likely working, which again points toward the HDMI board or HDMI input configuration.
For a final verification, use an analog RCA cable from a phone, CD player, or other simple source into a analog input on the TX-NR808. Analog audio uses a shorter and simpler signal path. If analog sound works but HDMI and digital inputs do not, the issue is almost certainly in the digital or HDMI processing section. If even analog remains silent, the problem may be in the preamp, DSP, speaker relay, or power amplifier stage.
When the Silence Points to Internal Onkyo TX-NR808 Faults
At this stage, you have ruled out the obvious settings and cable problems. The remaining causes are internal, and they range from protection circuits that shut down the amplifier to failed DSP chips and HDMI boards. The TX-NR808 is now an older receiver, so age-related failures are common. Heat is the enemy of these units, especially when they are installed in enclosed cabinets with poor ventilation.
Before assuming the worst, listen carefully when you power on the receiver. A healthy TX-NR808 usually clicks as its speaker relay engages a few seconds after startup. If you never hear that click, the receiver may be stuck in protection mode or the relay may not be closing. If the click occurs but there is still no sound, the amplifier may be receiving power but not an audio signal from the DSP or preamp section.
Protection Mode, Overheating, and Speaker Wiring
If the receiver turns off shortly after powering on, check for shorted speaker wires or loose strands touching the rear panel. Even a single stray wire can trigger protection mode and prevent sound. Disconnect all speakers, power on the receiver, and see whether it remains on. If it stays on without speakers connected, reconnect one speaker at a time until the fault returns. That process usually identifies the problematic wire or speaker.
Overheating can also cause the TX-NR808 to mute or shut down. Make sure the receiver has several inches of clearance above and around it, and clean dust from the ventilation openings if necessary. Speaker impedance is another factor. If you are using low-impedance speakers, check the receiver’s speaker impedance setting in the menu and set it appropriately. Running a demanding speaker load at high volume can push an aging amplifier into protection.
DSP Chip, Firmware, and HDMI Board Failures
The TX-NR808 relies on a DSP chip for surround decoding, bass management, and digital audio processing. When that chip fails or loses communication with the HDMI board, you may get no sound from all digital inputs while the receiver still powers on normally. Some owners also report distorted audio, audio dropouts, or a loud pop before the sound disappears. These symptoms are classic signs of a board-level fault rather than a simple settings error.
A factory reset can clear corrupted memory and restore default audio paths. On many Onkyo receivers, you can perform a reset by holding a specific input button while pressing the power button, then waiting for the display to show Clear or Complete. The exact procedure varies, so check the TX-NR808 manual before trying it. Firmware updates may also help if the problem began after a network or HDMI change, but they cannot repair failed capacitors, a dead DSP, or a damaged HDMI receiver chip.
If your Onkyo TX-NR808 still refuses to produce sound after basic checks, input swaps, a factory reset, and speaker isolation, the receiver has likely reached the point where professional service or replacement is the practical choice. A repair shop can test the HDMI board, DSP, and amplifier stages directly, but the cost may approach the price of a modern replacement. If you decide to keep the TX-NR808 alive, focus on ventilation, correct speaker impedance, and stable power to help the remaining components last longer. With a clear diagnosis in hand, you can either restore the receiver to service or move on to a new unit without second-guessing the decision.