lifted subaru brat

Lifted Subaru Brat: The Ultimate Off-Road Build Guide

By David Lee
AD

The Subaru Brat is one of the great automotive oddballs of the late twentieth century. Sold in North America from 1978 through 1987, this tiny car-based pickup — officially the Bi-drive Recreational All-terrain Transporter — paired part-time four-wheel drive with a bed containing two rear-facing jump seats and a set of grab handles straight out of a theme park ride. It was cheap, slow, rust-prone, and utterly charming. It was also, quietly, a legitimate trail vehicle waiting for a few inches of altitude.

That is exactly what a lifted Subaru Brat delivers. Raise the body and suspension a couple of inches, fit taller tires, and a machine that once struggled over a rutted fire road suddenly clears rocks, water bars, and washouts with composure. The Brat weighs roughly 2,000 to 2,300 pounds depending on year and equipment, so even its modest flat-four engine has far less mass to drag around than a modern crossover. Lift one properly and you get a rig that punches well above its displacement.

Why the Subaru Brat Responds So Well to a Lift

Most vehicles gain clearance grudgingly. You add a spacer here, trim a fender there, and the geometry turns hostile. The Brat is different because its architecture is simple and mechanically honest. Up front you get MacPherson struts on the later EA81 cars, and out back a trailing-arm setup sprung by torsion bars. There are no complex multi-link arms, no electronic ride control, no subframe bushings engineered to fight you. A competent fabricator can raise the nose with strut spacers and lift the tail by re-indexing those torsion bars, and the whole job stays refreshingly analog.

AD
Subaru Brat battle truck
Subaru Brat battle truck
Subaru Brat
Subaru Brat
a white truck parked on top of a dirt road
a white truck parked on top of a dirt road

Equally important, the Brat was built small on purpose. Its short wheelbase and narrow track make it nimble in tight terrain, and its light curb weight means stock brakes, stock axles, and a stock clutch can tolerate modest lift-and-tire upgrades without immediate protest. Compare that to lifting a full-size truck, where every change cascades into steering geometry, driveline angles, and a four-figure parts bill. On a Brat, a basic lift is an afternoon project and a modest budget.

A Brief Look at the Brat's Chassis and Drivetrain

The Brat rode on Subaru's Leone platform, which means unibody construction rather than a separate frame. That is not a weakness in this context — the shell is stiff for its era and light enough that a small lift does not stress it unduly. Power came from the EA71 1.6-liter flat-four in early cars, replaced by the EA81 1.8-liter later in the run. Output hovered in the 65 to 75 horsepower range, paired with a four-speed manual. Four-wheel drive was part-time, engaged via a lever, and by the early 1980s a dual-range transfer case became available on some models — a genuine advantage once you bolt on larger tires.

Subaru Brat
Subaru Brat
Bringing back a new life to the iconic Subaru Brat, Jason Osborne
Bringing back a new life to the iconic Subaru Brat, Jason Osborne
1984 Subaru BRAT GL Automatic For Sale in Madisonville, Tennessee
1984 Subaru BRAT GL Automatic For Sale in Madisonville, Tennessee

Two specifications matter enormously when you start shopping for lift parts. First, the wheel bolt pattern is 4x140mm, an oddball size that limits aftermarket wheel choices and pushes many owners toward adapters or redrilled hubs. Second, the rear suspension uses torsion bars that can be re-indexed to gain height without buying much of anything. Knowing these two facts before you spend a dollar will save you a great deal of frustration later.

What a Lift Kit Actually Changes

A lift kit for a Brat is not one product but a category of solutions. Strut spacers sit on top of the front strut assemblies and push the body upward while retaining factory spring rates. Subframe spacers, sometimes called a body lift, drop the entire front crossmember and engine cradle relative to the unibody, which preserves suspension geometry at the cost of raising the center of gravity. Rear torsion bar re-indexing rotates the bar within its splines to raise ride height, often supplemented by longer shocks and taller bump stops.

AD

The measurable result is improved approach, departure, and breakover angles, plus room for larger tires. The tire clearance is where most of the real-world capability comes from. Lifting without upsizing tires gives you a taller rig that still high-centers on the same rocks. Lifting with taller, more aggressive rubber gives you a machine that can genuinely crawl. There is also a hidden cost to be aware of: every inch of front lift increases the angle at which the CV axles operate, and past roughly three inches, axle bind and boot wear become real concerns.

Subaru Brat and bike
Subaru Brat and bike
Ruge's Subaru: Photo
Ruge's Subaru: Photo
1982 Subaru Brat Off-Road Build
1982 Subaru Brat Off-Road Build
a truck is driving through some mud
a truck is driving through some mud
a red truck parked on the side of a road next to a white pickup truck
a red truck parked on the side of a road next to a white pickup truck
Ruge's Subaru
Ruge's Subaru

Choosing the Right Lift Height and Hardware

Most Brat owners land somewhere between two and four inches of lift, and that range covers the overwhelming majority of trail use. A two-inch lift with a tasteful tire upgrade is the sweet spot for a daily-driven Brat that sees gravel roads, forest service tracks, and the occasional muddy two-track. It keeps steering effort reasonable, preserves some semblance of highway manners, and does not require cutting or welding. Four inches opens the door to serious tire sizes and dramatically better breakover clearance, but it also demands attention to driveline angles, brake line length, and steering geometry.

Beyond five or six inches you are into custom territory — custom control arms, longer axles, fabricated subframes, and a substantial budget. At that point the Brat stops being a quirky classic and starts being a dedicated rock crawler, which is a perfectly valid goal but a very different build philosophy. Decide what you actually want to drive before you decide how tall you want to sit.

AD

Suspension Lift vs. Body Lift vs. Subframe Drop

A suspension lift raises the chassis relative to the wheels, which means more ground clearance under the drivetrain and better suspension travel if you pair it with the right shocks and springs. A body lift raises the shell relative to the subframes, which gains tire clearance and a taller stance without altering suspension geometry at all. A subframe drop sits somewhere between the two — the body goes up, but the engine cradle and suspension mounting points come down with it, keeping CV angles and steering geometry closer to factory.

an off - road vehicle is parked in the dirt
an off - road vehicle is parked in the dirt
1984 Subaru Brat GL 4×4
1984 Subaru Brat GL 4×4
Subaru Brat
Subaru Brat
an off road vehicle is jumping over a fence in the dirt while people watch from behind it
an off road vehicle is jumping over a fence in the dirt while people watch from behind it

For a Brat, the practical answer is usually a hybrid. Strut spacers and torsion re-indexing handle the front and rear ride height, while modest body spacers create the fender clearance needed for bigger tires. If you plan to run anything past a 27-inch tire, expect to combine approaches. Talk to owners who have built the exact configuration you are considering, because the Brat community has already made most of the mistakes so you do not have to.

Tires, Wheels, and Gearing After the Lift

Wheel selection is the single biggest headache in Brat ownership. The 4x140mm bolt pattern is shared with very little, though 15-inch Peugeot wheels from certain 505 models are a legendary swap in the community. Otherwise you are looking at redrilled hubs, bolt-on adapters, or a handful of specialty suppliers making wheels in the correct pattern. Whatever route you take, keep offset in mind — pushing the wheels outward widens the track and looks fantastic, but it also increases scrub radius and load on wheel bearings.

AD

Tire sizing follows the lift. A two-inch-lifted Brat typically runs a 25- to 26-inch tire comfortably. At three to four inches, 27-inch tires such as a 27x8.5R14 become realistic. Push toward 28 or 30 inches and you are trimming fenders, hammering seams, and accepting that gearing will feel noticeably taller. That last point matters more than most first-time builders expect.

  • Stock height: 23- to 24-inch tires, no clearance concerns
  • 2-inch lift: 25- to 26-inch tires, minimal trimming
  • 3- to 4-inch lift: 27-inch tires, some fender massaging
  • 5-inch-plus: 28- to 30-inch tires, custom fabrication likely

The EA81 makes roughly 70 horsepower on a good day, and taller tires multiply the effective final drive ratio in a way that feels dramatic in a light vehicle. A Brat that cruised happily at highway speed on stock rubber will suddenly feel breathless on hills. A dual-range transfer case is the single most valuable upgrade here, since the low range effectively restores crawling ability and lets you keep the engine in its narrow power band off-road. If your Brat lacks one, sourcing a dual-range gearbox is one of the highest-value modifications you can make alongside the lift itself.

Living With and Driving a Lifted Brat

Owners who lift their Brats and then complain about the ride usually made one mistake: they changed height without changing shocks or springs. Stock-length dampers run out of travel quickly once you add spacers, which produces a harsh, bouncy ride and premature component wear. Fit appropriate longer shocks, replace tired bushings, and the Brat remains surprisingly pleasant. It will never be a luxury car, but a well-sorted lifted Brat tracks straight, steers with reasonable weight, and does not wander in crosswinds the way a poorly executed lift will.

On-road, expect more wind noise, a slightly higher center of gravity in corners, and a noticeable appetite for brakes if you have fitted heavy off-road tires to a 1970s braking system. Off-road, the transformation is dramatic. The short wheelbase that makes the Brat twitchy on the highway becomes an asset on tight trails, and the light weight means it floats over soft ground where heavier rigs dig in. For backcountry access roads, ranch tracks, and overlanding on a shoestring, a lifted Brat is genuinely hard to beat.

Supporting Modifications That Matter

Once the lift is on, a handful of supporting upgrades dramatically improve the ownership experience. Extended brake lines prevent the factory rubber hoses from being stretched at full droop, a failure that is both dangerous and entirely avoidable. A modest skid plate protecting the oil pan and transmission is worth its weight in gold on rocky terrain. Fresh ball joints, tie rod ends, and sway bar bushings tighten up steering that has likely been vague for decades.

Cooling deserves attention too. The EA series engines are tough, but a tired radiator, a worn fan clutch, and low-speed crawling are a poor combination. A recored or upgraded radiator, a new thermostat, and fresh coolant hoses cost little and prevent the kind of overheating that turns a fun weekend into a tow-truck story. If your Brat still wears its factory rear jump seats and roll bar, inspect the mounting points thoroughly — those components are structural as well as nostalgic.

Maintenance, Parts, and Community Support

Parts availability is the Brat owner's constant companion, both good and bad. Wear items like brakes, bearings, and ignition components are often still available through specialty suppliers, and the aftermarket for small-batch lift kits, suspension bushings, and adapters is kept alive by a dedicated community of fabricators. Sheet metal, however, is scarce, and rust is the Brat's true nemesis. Any lift project should begin with a hard look at the floor pans, rocker panels, strut towers, and rear subframe mounts before you spend money on altitude.

Because these vehicles are rare and mechanically unusual, the enthusiast network is invaluable. Owner forums, regional Subaru groups, and marque-specific social media communities are where you will find NOS parts, fabrication drawings, and hard-won installation tips. When you are dealing with oddball bolt patterns and 40-year-old torsion bars, tribal knowledge is worth more than any catalog.

Two practical matters deserve a mention before you commit. First, check your local inspection and modification laws — some jurisdictions have ride height rules or require engineering approval for suspension changes. Second, talk to your insurer about declared modifications, because a lifted Brat with custom suspension is not a stock vehicle, and an accident is a terrible time to discover a coverage gap.

There is something genuinely satisfying about watching a lifted Subaru Brat roll down a trail with a bed full of gear and two absurd little jump seats sticking up behind the cab. It is not fast, it is not refined, and it will absolutely require more attention than a modern 4x4. But every one of these builds is a small act of preservation, keeping a strange and wonderful corner of automotive history alive and useful rather than parked and forgotten. If you have been sitting on a stock Brat and wondering whether to lift it, the answer is almost certainly yes — measure twice, budget for shocks, and start turning wrenches. The trails are waiting, and your Brat has been ready for forty years.

AD