Larson Storm Door Installation: Step-by-Step Guide
Installing a Larson storm door is a DIY project that enhances your home's security, energy efficiency, and curb appeal. With the right tools and instructions, you can complete this task in a weekend. Let's dive into step-by-step instructions for a smooth and successful Larson storm door installation.
Before you start, gather your tools and materials. You'll need a drill, screwdriver, tape measure, level, safety glasses, gloves, and your new Larson storm door, along with its hardware kit.
Preparing for Installation
The first step involves measuring and preparing your door frame for installation. Ensure your storm door is compatible with your main entry door's width and height.



Remove any existing hardware or door stoppers from your door frame. Clear the area around the door frame to provide enough space for installation. Also, lay down a drop cloth to protect your floor from any debris or paint.
Measuring Your Door Frame
Accurate measurements are crucial for a proper fit. Use your tape measure to verify the width and height of your door frame. Measure from the top of the threshold to the bottom of the head jamb for the height, and from one side jamb to the other for the width.



Compare your measurements with the size of your new Larson storm door. If necessary, trim the door's top EdgeGuard to match the height of your door frame. Be careful not to trim too much, as the EdgeGuard provides essential protection and weatherproofing.
Assembling Your Storm Door
Before mounting the door on its hinges, assemble the screen and front panel. Snap the screen into the frame and secure it with the provided clip or screw. Attach the front panel by aligning the side tabs with the edge of the frame and sliding it into place.
Now, insert the door's pivot arm into the top hinge, and attach the butt hinge to the side edge of the door. Ensure that both hinges are properly aligned and secure them with the provided screws. Do not fully tighten the screws at this point, as you'll need to adjust the door's alignment during installation.






Installing the Top Hinge and Pivot Arm
Position the door in the frame and mark the location for the top hinge. The pivot arm should be centered on the top of the door frame.
Pre-drill holes at the marked locations, then attach the top hinge to the door frame using the provided screws. Ensure the hinge is level and the pivot arm moves smoothly within its range. Make any necessary adjustments to the screw tension before fully tightening them.
Attaching the Side Hinge
With the top hinge secured, position the door in the frame and mark the location for the side hinge. The hinge should be aligned with the side edge of the door and centered vertically.

Pre-drill holes at the marked locations and attach the side hinge to the door frame using the provided screws. Check that the door swings smoothly and evenly. Adjust the screw tension as needed, ensuring the door aligns properly with the frame and the stop。
Installing the Strike Plate and Latch
The strike plate and latch work together to keep the storm door closed and secure. Attach the strike plate to the inside of the door frame, aligning it with the door's latch. Use the provided screws to secure the strike plate.
Next, attach the latch to the outside of the storm door, ensuring it aligns with the strike plate. Secure the latch using the provided screws. Test the door to ensure it latches and unlatches smoothly.
Finishing Touches
With the door now installed and functional, you can complete the installation with a few finishing touches.
Trim any excess EdgeGuard from the bottom of the door, if necessary. Then, install the door sweep by aligning it with the bottom of the door and securing it with the provided screws. The door sweep helps keep drafts and debris out of your home.
Adjusting the Door Alignment
Perform a final check of the door's alignment. The door should swing freely and close snugly against the frame. Use the adjustment screws in the hinges to fine-tune the door's alignment if needed.
Once you're satisfied with the door's alignment, fully tighten the hinge screws. Now, your new Larson storm door is well-SECURED, ENERGY-efficient, and ready to protect your home for years to come.
Remember, regular maintenance, such as cleaning and lubricating the hinges, will help keep your Larson storm door in optimal condition. Enjoy the added security, energy efficiency, and beauty that your new storm door brings to your home.



