Kobalt Drill Review: Top Cordless Models, Features, and Buying Guide
Cobalt drill bits occupy a specific niche in the toolbox: they are the bits you reach for when ordinary high-speed steel gives up. Anyone who has tried to drill a hole in a stainless steel bracket with a standard bit knows the sound — a high-pitched squeal, a puff of smoke, and a cutting edge that is suddenly dull. Cobalt bits exist to solve that exact problem, and they do it by surviving heat that would destroy a conventional bit in seconds.
Understanding what cobalt actually does inside the steel, when it is worth the extra money, and how to run it correctly will save you a fortune in replacement bits and ruined projects. This guide covers the metallurgy, the practical differences between the common grades, and the techniques that separate a clean, fast hole from a burned-out drill bit.
What Makes Cobalt Drill Bits Different
The most common misunderstanding about cobalt bits is that cobalt is a coating. It is not. Titanium nitride, titanium aluminum nitride, and black oxide are coatings applied to the surface of a bit. Cobalt is an alloying element melted into the steel itself, distributed through the entire body of the drill. That distinction matters because when a coated bit loses its coating through sharpening or wear, the underlying metal is just ordinary high-speed steel. A cobalt bit remains a cobalt bit all the way to the shank.
The benefit comes down to heat resistance, often called red hardness. When you cut metal, the tip of the drill generates enormous friction heat. Standard HSS begins to soften somewhere around 900 degrees Fahrenheit, and once it softens, the cutting edge rounds over and stops cutting. Cobalt raises that softening threshold, allowing the bit to keep its edge at temperatures that would ruin a conventional drill. You get more holes per bit, faster cutting, and far less downtime swapping out dull tools.
The Metallurgy Behind Cobalt Steel
Cobalt drill bits are classified as high-speed steel with a cobalt addition, typically written as HSS-Co. The two grades you will see on packaging are M35, which contains roughly 5 percent cobalt, and M42, which contains about 8 percent cobalt plus a higher molybdenum content. Both are variations on the molybdenum-series high-speed steels developed for tooling that has to hold an edge under heavy thermal load. The cobalt content raises the tempering temperature of the steel, which is the practical reason the bit resists softening.
What this means at the drill press is that the bit tolerates more surface speed and more pressure before it fails. That characteristic is especially valuable on work-hardening materials. Stainless steel, for example, gets harder as it is rubbed rather than cut, so a bit that slides without biting will make the workpiece progressively more difficult to machine. A sharp cobalt edge bites immediately and keeps biting, which prevents the material from work-hardening ahead of the cut.
M35 vs M42: Which Grade Do You Need?
M35 is the practical everyday choice for most workshops. It is slightly tougher and more resistant to chipping than M42, costs less, and handles mild steel, aluminum, brass, cast iron, and moderate stainless steel without complaint. If you are drilling general fabrication material and occasionally hitting a stainless fastener, M35 is the sensible buy. It is also more forgiving for hand-held drilling, where the bit inevitably gets loaded off-axis.
M42 is the premium option for hard and abrasive materials: hardened tool steel, high-alloy stainless, titanium alloys, and Inconel. The trade-off is brittleness. M42 bits can chip or snap if you apply side load, wobble the drill, or use them in a hand drill with poor control. They belong in a drill press or a rigid setup where the bit can run true. Many machinists keep both grades on hand and pick based on the material rather than defaulting to the more expensive one.
| Property | M35 (5% Cobalt) | M42 (8% Cobalt) |
|---|---|---|
| Hardness | Approx. 64-66 HRC | Approx. 66-68 HRC |
| Toughness | Higher, more forgiving | Lower, more brittle |
| Best For | Mild steel, stainless, general metalwork | Hardened steel, titanium, high-alloy stainless |
| Cost | Moderate | Higher |
Putting Cobalt Bits to Work
A cobalt bit is not a license to ignore drilling fundamentals. In fact, it punishes bad technique just as harshly as a cheap bit does, only the failure is more expensive. The single most common mistake is running the drill too fast. Because cobalt resists heat, operators assume they can spin it as fast as they like, but excessive speed still destroys the edge, just a little more slowly than it would on HSS.
The second common mistake is insufficient pressure. A drill bit needs to bite and produce a chip. If the point rubs against the surface without cutting, the material work-hardens and the heat builds in the worst possible place. You want firm, steady feed that keeps the cutting edges engaged and produces visible chips or curls coming off the flutes. If you see fine dust instead of chips, you are rubbing, not cutting.
Speeds, Feeds, and Cutting Technique
Cutting speed is measured in surface feet per minute at the outer edge of the bit, and larger bits have to turn slower than small ones to maintain the same edge speed. As a rough workshop rule for cobalt on mild steel, use about 30 to 35 surface feet per minute. For a half-inch bit that works out to roughly 250 RPM; for a quarter-inch bit, around 500 RPM; for an eighth-inch bit, around 1,000 RPM. Stainless steel needs to run slower still, closer to 20 to 25 surface feet per minute.
Always use a cutting fluid. On steel and stainless, a sulfurized or chlorinated cutting oil makes a dramatic difference in tool life. Apply it continuously rather than in one squirt at the start. For deep holes, peck drill in short increments to clear chips and let the bit cool, and consider a pilot hole for anything larger than three-eighths of an inch. Never use a cobalt bit in hammer mode, and never use one on masonry or concrete — those materials require carbide, and the hammer action will shatter the cutting edges instantly.
Sharpening, Care, and Longevity
Cobalt bits respond well to sharpening, which is one of their underrated advantages. A 135-degree split point is the standard geometry for metal drilling because it reduces the force needed to start the hole and resists walking on curved or uneven surfaces. Sharpening on a bench grinder requires a light touch: grind the flank, maintain the original angle, and dunk the bit in water frequently. If the tip turns blue or straw-colored, you have overheated it and softened the steel, which defeats the purpose of buying cobalt in the first place.
A diamond wheel or a dedicated drill bit sharpener gives far better results than a general-purpose grinding wheel, especially for maintaining the split point. Between sharpenings, protect the bits from corrosion with a light oil wipe and store them in an index case so the edges are not nicked by each other. Avoid using your good cobalt bits for wood, drywall, or plastic. They will cut those materials, but they are overkill for the job and the abrasive dust is not kind to the edge.
Choosing the Right Cobalt Drill Set
Buying cobalt bits is a case where the specifications matter more than the marketing copy on the front of the box. The word "cobalt" gets used loosely, and some products advertised as cobalt are simply titanium-coated HSS. A genuine cobalt bit will be marked HSS-Co, M35, or M42 on the shank or the packaging, and a full set from a reputable manufacturer will state the grade clearly rather than burying it in small print.
Think about the sizes you actually use. A 29-piece fractional set from 1/16 inch to 1/2 inch covers most general work, while a 115-piece letter, number, and fractional set is aimed at machinists who drill specific tap and clearance sizes. For most people, a good 15- or 21-piece set in the sizes they use weekly, supplemented with individual replacements, is more practical and less expensive than a giant set full of bits that never come out of the case.
Reading Specs and Spotting Inferior Bits
Check the point geometry, the shank, and the finish. A properly ground 135-degree split point, clean flutes with no visible grinding burns, and a straight, true shank are all signs of quality. Bits that arrive with a waxy coating or a vague rainbow sheen on the flutes may have been overheated during manufacturing, which leaves them soft before you ever use them. Round-shank bits fit standard chucks; reduced-shank bits let you run large diameters in a half-inch chuck.
Also consider length. Jobber-length bits are the general-purpose standard. Mechanics-length bits are shorter and stiffer, which makes them ideal for tight spaces and less likely to snap under hand-drilling loads. Aircraft extension bits are longer for reaching through obstructions. Buying a mix of lengths in the sizes you use most will serve you better than one uniform set, particularly if you do repair work on vehicles or machinery.
Matching the Bit to the Material
Cobalt covers a wide range, but it is not unlimited. Mild steel, stainless steel, cast iron, brass, bronze, and aluminum are all fair game, and cobalt handles them with ease. Aluminum is worth a caveat: the standard 135-degree point can gall and clog on soft aluminum because the material sticks to the edge. A polished HSS bit with a sharper point and a bit of lubricant often performs better on aluminum than cobalt does. Use what suits the material, not what cost the most.
For hardened steel above roughly 35 HRC, cobalt is no longer the right answer. Drill bits in that hardness range need solid carbide, and in some cases the part needs to be annealed before machining. Trying to force a cobalt bit through hardened tool steel will ruin the bit quickly. Recognizing the ceiling of the material is as important as choosing the bit itself, and it is the difference between a tool that lasts years and one that dies on its first job.
If you have been burning through cheap bits on stainless and hardened fasteners, a small set of genuine M35 cobalt bits is one of the better upgrades you can make to your shop. Start with the sizes you use most, learn to run them slower than you think you should, and keep them sharp rather than replacing them. Once you have drilled a dozen clean holes in material that used to fight back, going back to ordinary high-speed steel will feel like a downgrade you are not willing to make.