kenmore dishwasher wont drain

Kenmore Dishwasher Won't Drain? 7 Easy Fixes to Get It Draining Again

By Nicole Thomas
AD

You open the door after a wash cycle expecting sparkling glasses and instead find a pool of murky water sitting at the bottom of the tub. A Kenmore dishwasher that won't drain is one of the most frustrating appliance failures you can run into, largely because it usually happens right when you need the machine the most. The good news is that the overwhelming majority of "Kenmore dishwasher not draining" complaints trace back to a handful of predictable culprits, and many of them can be diagnosed with nothing more than a flashlight and a towel.

Before you start shopping for a replacement, it pays to understand how the drain cycle actually works on your specific machine. Kenmore dishwashers have been built by several different manufacturers over the decades, most notably Whirlpool for the popular 665 series and Frigidaire for the 587 series, and each platform routes water out of the tub in a slightly different way. Knowing which family your model belongs to will save you a lot of guesswork.

Common Reasons a Kenmore Dishwasher Won't Drain

Standing water in the bottom of the tub almost always means something is blocking, breaking, or confusing the drain path. That path includes the filter assembly, the sump, the drain hose, the air gap or disposal connection, the check valve, and finally the drain pump itself. If any single link in that chain fails, water has nowhere to go and simply accumulates until the float switch or the control board shuts the cycle down.

AD
Kenmore Dishwasher Model 665 Troubleshooting: Expert Tips
Kenmore Dishwasher Model 665 Troubleshooting: Expert Tips
Kenmore Dishwasher Draining Problem - Ready To DIY
Kenmore Dishwasher Draining Problem - Ready To DIY
Dishwasher Does Not Drain - How To Fix
Dishwasher Does Not Drain - How To Fix

It is also worth noting that a Kenmore dishwasher can appear to have a drain problem when the real issue is a control or sensor fault. If the control board never sends voltage to the drain pump, the pump will sit silent and the tub will fill with water just as surely as if the pump had burned out. That distinction matters because it changes whether you are replacing a mechanical part or an electronic one.

Clogged Filter and Chopper Assembly

The filter sits at the lowest point of the tub and catches food particles, grease, and bits of broken glass before they can reach the pump. Over time, a layer of sludge builds up on the mesh and around the filter housing, and water drains more and more slowly until it stops draining altogether. On many Kenmore models you can lift the lower rack, twist the cylindrical filter counterclockwise, and pull the whole assembly straight up for inspection.

the inside of a dishwasher with wires attached to it and other parts labeled
the inside of a dishwasher with wires attached to it and other parts labeled
Dishwasher Not Draining? Try This Before You Call a Pro
Dishwasher Not Draining? Try This Before You Call a Pro
Is Your Dishwasher Not Draining? Try This Before Calling a Plumber
Is Your Dishwasher Not Draining? Try This Before Calling a Plumber

Once the filter is out, shine a flashlight into the sump area underneath. You are looking for standing debris, a film of greasy sludge coating the screen, or objects like a cherry pit, a piece of bone, or a shard of glass wedged into the chopper blades. Rinsing the filter under hot running water and scrubbing it with a soft brush often restores full drainage in minutes, though heavily caked assemblies may need a soak in warm soapy water first.

Kinked, Clogged, or Frozen Drain Hose

The drain hose carries dirty water from the pump to either the garbage disposal, the sink tailpiece, or a dedicated drain in the cabinet beside the sink. Because this hose loops and bends behind the unit, it is easy for it to get pinched against the cabinet wall when the dishwasher is pushed back into place. A sharp kink acts like a clamp and will completely stop the flow of water.

AD

If the hose is not kinked, it may be clogged internally with years of accumulated grease and food paste. Disconnect the hose at both ends, drain it into a bucket, and inspect it by holding it up to a light. In unheated garages or vacation homes, a drain hose can also freeze solid during cold snaps, which produces the exact same symptom and thaws on its own once the space warms up.

Kenmore dishwasher model 665 repair manual
Kenmore dishwasher model 665 repair manual
Frigidaire Dishwasher Is Not Draining? How To Drain It Explained
Frigidaire Dishwasher Is Not Draining? How To Drain It Explained
My Kenmore Dishwasher Won't Drain and is Leaking- How to fix or repair Clog or Leak. Not pumping.
My Kenmore Dishwasher Won't Drain and is Leaking- How to fix or repair Clog or Leak. Not pumping.
Kenmore Dishwasher Keeps Tripping Breaker/Blowing Fuse - Ready To DIY
Kenmore Dishwasher Keeps Tripping Breaker/Blowing Fuse - Ready To DIY
3 Easy Ways To Fix Kenmore Portable Dishwasher Won't Drain - Miss Vickie
3 Easy Ways To Fix Kenmore Portable Dishwasher Won't Drain - Miss Vickie
Kenmore Dishwasher Repair – How to replace the Drain Pump- 60Hz 120V
Kenmore Dishwasher Repair – How to replace the Drain Pump- 60Hz 120V

Troubleshooting the Drain System Step by Step

Working through the drain system methodically is far more efficient than replacing parts at random. Start with the simplest and most accessible components, then move toward the pump and wiring only after everything upstream has been ruled out. Keep a shallow pan and several old towels handy, because any time you disconnect a drain component there will be residual water waiting to spill.

Before you touch anything, kill power to the dishwasher at the breaker panel. Water and live electricity are a dangerous combination, and most drain-related repairs put your hands uncomfortably close to the pump wiring. Once the breaker is off, pull the machine forward far enough to access the rear panel and the drain connections.

AD

The Air Gap and Garbage Disposal Connection

If your kitchen sink has an air gap mounted on the countertop, that small chrome cylinder is a surprisingly common reason a Kenmore dishwasher won't drain. The air gap prevents dirty sink water from siphoning back into the dishwasher, but its internal cap and holes can clog with grease and grit. Twist off the outer cover, lift out the plastic cap, and clean both pieces thoroughly with hot water and a small brush.

Kenmore He2 washing machine washer drain problem fixed
Kenmore He2 washing machine washer drain problem fixed
Kenmore Dishwasher Filling Water Problems - Ready To DIY
Kenmore Dishwasher Filling Water Problems - Ready To DIY
Kenmore Whirlpool Dishwasher Diverter Valve Seal Grommet Leak Repair
Kenmore Whirlpool Dishwasher Diverter Valve Seal Grommet Leak Repair
a dishwasher filled with lots of dishes and utensils in black and white
a dishwasher filled with lots of dishes and utensils in black and white

The garbage disposal connection is the other classic trap. When a new disposal is installed, the knockout plug inside the dishwasher inlet must be removed before the drain hose is attached. If that plug was left in place, the dishwasher will never drain properly, and the problem will appear the very first time you run a cycle after the installation.

Testing the Drain Pump and Check Valve

On Whirlpool-built Kenmore models in the 665 family, the drain pump is usually a small separate pump mounted to the side of the sump, while Frigidaire-built 587 models often use a reversible motor that spins one direction to wash and the opposite direction to drain. Either way, you can test the pump by applying direct power to its terminals with a multimeter or a test cord once the machine is unplugged from the control board. A pump that hums without moving water is jammed, and one that stays silent with good voltage is dead.

AD

The check valve, sometimes called a flapper valve, is a small rubber or plastic flap near the pump outlet that allows water to leave the tub but prevents it from flowing back in. If the flap is warped, stuck open, or coated in grease, water can circulate back into the tub and make it look like the dishwasher never drained at all. Removing the valve and cleaning or replacing it is a cheap fix that resolves a surprising number of repeat drain complaints.

Preventing Future Drain Problems

Once you have the water flowing again, a few simple habits will keep your Kenmore draining reliably for years. Most drain failures develop gradually, which means they can be prevented with consistent, low-effort maintenance rather than emergency repairs. The goal is to keep grease, food solids, and detergent residue from ever building up enough to restrict the flow.

It also helps to know your model's error codes. Whirlpool-built Kenmore dishwashers commonly display codes related to long drain times or drain pump faults, while Frigidaire-built units often flash a drain-related indicator light pattern. Writing those codes down before you call for service gives a technician a head start and can save you money on diagnostic time.

Simple Maintenance Habits

Scrape plates thoroughly before loading, but do not pre-rinse everything to a shine, since a little food soil actually helps some detergents work. Run a hot water tap in the sink until it is steaming before you start the dishwasher, which ensures the first fill is hot enough to dissolve grease rather than depositing it in the drain path. Once a month, run an empty cycle with a dishwasher cleaner or a cup of white vinegar placed upright in the upper rack.

Clean the filter every few weeks if you run the machine daily. It takes less than two minutes, and it is the single most effective thing you can do to prevent a Kenmore dishwasher from refusing to drain. If you have hard water, consider a rinse aid and periodic descaling to keep mineral deposits from narrowing the sump passages.

Knowing When to Call a Technician

Some drain failures are genuinely beyond a do-it-yourself repair. If you have cleared the filter, confirmed the hose is clear, verified the disposal knockout is removed, and the drain pump still receives voltage but does not run, you are likely looking at a failed pump or a control board fault. Replacing a drain pump is manageable for a confident DIYer, but diagnosing control board issues requires schematics and a solid understanding of the wiring harness.

Also call for help if you see water leaking from underneath the unit during the drain cycle, if the dishwasher trips the breaker when it tries to drain, or if the machine is still under an extended warranty. Water damage from a slow leak can cost far more than a service call, and unauthorized repairs can void coverage on newer Kenmore units.

Dealing with a Kenmore dishwasher that won't drain is rarely as dire as it first appears, and most homeowners find the culprit within the first twenty minutes of investigation. Give the filter a thorough cleaning, check the hose for kinks and clogs, and make sure your disposal connection is actually open, then work your way toward the pump only if those steps come up empty. With a little patience and a flashlight, you can get the water moving again and get back to the part of the day that does not involve bailing out a dishwasher by hand.

AD