jeep wrangler side marker lights not working

Jeep Wrangler Side Marker Lights Troubleshooting: Not Working?

By Joshua Williams
AD

Got worried when your Jeep Wrangler's side marker lights stopped functioning? You're not alone. This issue can occur due to various reasons and can be quite puzzling, but with the right troubleshooting steps, you can get your Wrangler's safety lights back on track.

Before you dive into any fixes, remember that working with car electrics can be hazardous, so always ensure your vehicle is off and cooled down to avoid any risk. Now, let's Metalclay the issue and figure out why your side marker lights aren't working.

Common Culprits: Power and Wiring Issues

Like any car electrical problem, the first place to look at is the power source and the wiring route.

AD
Who knew 🤯
Who knew 🤯
How to Install: Hood LED Light Bar Kit for 2018-2023 Jeep JL Wrangler
How to Install: Hood LED Light Bar Kit for 2018-2023 Jeep JL Wrangler
2x Smoked Front Fender LED Repeat Side Marker Lights DRL Daytime Running Lamp For Jeep Gladiator JT
2x Smoked Front Fender LED Repeat Side Marker Lights DRL Daytime Running Lamp For Jeep Gladiator JT

Check the fuse box under the dashboard. Your side marker lights' fuse is usually logged as W5 or W6, although it might vary depending on your Wrangler's model and year. If the fuse is burnt out, replace it with an exact match.

Ground Issues

Next, check the ground connections. Poor contact at the ground point can cause components to malfunction. You can find the ground point under the dashboard near the battery.

How to Adjust Wrangler Headlights | 5 Easy Steps (2026)
How to Adjust Wrangler Headlights | 5 Easy Steps (2026)
an image of a jeep driving down the road with red lights on it's taillights
an image of a jeep driving down the road with red lights on it's taillights
the tail light of a gray jeep
the tail light of a gray jeep

Inspect the wires for any visible damage, corrosion, or broken connections. Use a multimeter to check for continuity, ensuring the circuit is complete between the light and the power source. If any wires are damaged, replace them with suitable ones.

Broken or Burnt Bulbs

A seemingly obvious issue but often overlooked, faulty or burnt-out bulbs can cause the entire circuit to fail. Even if other bulbs in the circuit are still working, a single burnt bulb can halt the entire system.

AD

Replace the bulbs with the correct type (usually 9006 or 7440, but check your owner's manual). Make sure to test each bulb before installing to rule out any faulty ones.

a person is changing the speed limit on a yellow vehicle
a person is changing the speed limit on a yellow vehicle
a man sitting in front of a jeep with the word jeep on it's bumper
a man sitting in front of a jeep with the word jeep on it's bumper
The Secret to remove Jeep Wrangler Doors #jeep #jeepwrangler #jeeplife
The Secret to remove Jeep Wrangler Doors #jeep #jeepwrangler #jeeplife

Faulty Switch and Relay

If the power and wiring are all in order, the issue might lie with the switch or relay mechanism controlling the lights.

Check the headlight switch. Sometimes, it might be stuck in the 'off' position due to a faulty component. The side marker lights should turn on when you turn the ignition to the 'on' position, so inspect this switch for any issues.

AD

Relay Malfunction

Controlled by a relay, side marker lights can malfunction due to a faulty relay. The relay is usually located in the engine compartment. Check the relay's pins for any signs of burn marks or corrosion.

Use a multimeter to test the relay. If it's faulty, replace it with a compatible one. However, before purchasing a new one, consider checking if your Jeep dealership offers a pre-assembled relay kit for convenience.

Water Damage or Moisture

Jeep Wranglers are designed to handle tough terrains, but water can seep into the electrical systems causing short circuits or damaged components. Inspect the wiring behind the lights for any signs of moisture or water damage.

AD

If water damage is found, clean the area thoroughly and ensure any affected parts are dried completely before reassembling. Apply some electrical sealant to protect the area from future moisture intrusion.

Remember, if you're unsure about any of these steps or lack the necessary tools, don't hesitate to consult a professional mechanic. Keeping your Wrangler's side marker lights working is crucial for safe night driving and adhering to traffic laws.

So, don't let a faulty side marker light dampen your off-road spirit. With a bit of troubleshooting and some elbow grease, you'll be back on the trail in no time, safely lighting the way with your Jeep Wrangler's side marker lights shining bright.

AD