IKEA PAX Closet Door Installation: Step-by-Step Guide
The IKEA PAX system is a game-changer for home organization, offering a sleek and customizable storage solution. Installing PAX closet doors is a rewarding task that enhances the functionality and aesthetic of your space. Here's a comprehensive guide to help you through the process.
Before you begin, ensure you have the right tools and materials. You'll need a Philips screwdriver, trim screws, an Allen key, a rubber mallet, and maybe a helper for certain steps. Your PAX door set should come with all the necessary hardware and instructions.
Planning Your PAX Closet Door Installation
Measure your wardrobe cabinet opening to ensure the door set you purchased fits correctly. PAX doors are typically 54 inches wide, so double-check your cabinet size, especially if you've made any customizations during assembly.



Also, decide whether you want your doors to swing in or out. Typically, doors open into the room unless you have specific needs, such as a narrow hallway.
Gather Your Tools and Materials
In addition to the tools mentioned earlier, ensure you have a tape measure, a pencil, and a level. It's also a good idea to have some masking tape to help identify hinge positions and a friend to assist with heavy lifting.



Double-check your PAX door set to ensure it includes: - Two door hangers (hinges) - Two door guides ( kecamixas) - Two adjustment screws - Four door pivots - Eight trim screws
Prepare Your PAX Wardrobe Cabinet
Your wardrobe cabinet should be fully assembled and level before installing the doors. Use the level to check the sides and ensure they're plumb (vertical alignment).
If you're installing the doors on an earlier IKEA PAX system (with the older black hinges), you may need to upgrade to the newer white hinges for a better fit. Always check with IKEA customer service if you're unsure.





Installing the PAX Closet Door Hinges
The hinges are what allow your doors to move smoothly. Mark the hinge positions on the cabinet. From the side of the cabinet, measure in 21.5 inches from the top and 11.75 inches from the bottom. Then, mark the center between these two points.
The most crucial step here is to ensure the hinges are perfectly level and aligned. Use your line level and a ruler to draw horizontal lines at the correct height. Then, attach the hinges to the cabinet using the provided hardware.
Attaching the Knockdown Dinners (Kecamixas) to Your PAX Doors
The knockdown dinners are the part of the hinge that attaches to the door. One is located at the top of each door, about 2 inches from the top. Use the provided Allen key to attach them. Be careful not to overtighten.
Starting from inside the door, push the knockdown dinner through the hole, and then secure it from the outside with the Allen key.
Attaching the Door Pivots
Locate the bottom of your PAX door, where the pivot will sit. Again, measure 11.75 inches from the bottom. Mark the center between this point and the edge of the door, then drill a small pilot hole.
Insert the pivot point through the hole from the inside of the door. Secure it from the outside using the provided hardware. Repeat this process for both doors.
Aligning and Installing the PAX Doors
With the hinges and pivots in place, it's time to install the doors. Carefully pick up the door and align it with the hinges on the cabinet. The pivot point at the bottom should slide into the matching hole on the cabinet floor.
Slowly lower the door into place. It should sit snugly and open and close smoothly. Use the adjustment screws on the hinges to fine-tune the door's swing and alignment if necessary.
Securing Your PAX Doors with Trim Screws
With the doors aligned and swinging smoothly, it's time to secure them. Measure and mark the position for the trim screws on the cabinet. These should be about 1 inch from the top and bottom of the door, equidistant from the sides.
Drill a pilot hole at each mark. Then, use the trim screws to secure the door to the cabinet frame. You may need to use a rubber mallet to gently tap the door to achieve a snug fit.
Congratulations, you've successfully installed your PAX closet doors! Always double-check that they open and close smoothly. If not, tighten or adjust the screws as necessary. Now, sit back and admire your newly organized space.




