igniter 316489403

Igniter 316489403 – Premium Replacement Gas Oven Igniter for Reliable Lighting

By Brian Martin
AD

When a gas oven refuses to light but the igniter still glows a dull orange, the culprit is often the hot surface igniter — and for thousands of Frigidaire-built ranges, that component carries the part number 316489403. This small ceramic-and-metal assembly is one of the most frequently replaced parts in a gas range, yet few homeowners understand what it actually does, why a glowing part can still be broken, or how to tell the difference between an igniter problem and a gas valve problem. Getting that diagnosis right saves both money and time.

This article walks through everything you need to know about the igniter 316489403: what it does inside the oven cavity, which appliance brands and models it fits, how to test it with basic tools, and how to replace it without damaging the new part or creating a safety hazard. Whether you are a DIY-minded homeowner or a technician verifying a part number before ordering, the details below are meant to be practical rather than theoretical.

What the Igniter 316489403 Actually Does

The 316489403 is a hot surface igniter, sometimes called a glow-bar igniter. It is a small, brittle element made largely of silicon carbide or a comparable ceramic material that becomes electrically conductive and extremely hot when voltage is applied. During a bake cycle, the igniter heats to well over 1,800 degrees Fahrenheit, hot enough to ignite the stream of gas flowing from the bake burner without any pilot flame or spark.

AD
316489403 Oven Igniter Replacement For Gas Stove, Fit For Frigi-daire Ken-more
316489403 Oven Igniter Replacement For Gas Stove, Fit For Frigi-daire Ken-more
Electrolux Range Igniter 316489403CM
Electrolux Range Igniter 316489403CM
an open box with some type of metal object on the table next to it's contents
an open box with some type of metal object on the table next to it's contents

What makes this part more than a simple heater is its role in the safety circuit. On most modern gas ranges, the igniter is wired in series with the gas safety valve. The valve does not open simply because the thermostat calls for heat — it opens because the igniter draws a specific amount of current as it heats up. That current is what energizes the valve coil and releases gas. In other words, the igniter is both the ignition source and an indirect sensor of its own health.

Where It Sits Inside the Oven

In most Frigidaire-family ranges, the igniter 316489403 is mounted on a metal bracket near the bake burner tube, typically along the rear wall or beneath the oven floor. Two wires run from the igniter to a connector, which in turn ties into the range's wiring harness and the gas safety valve circuit. Because it lives inside the hot, greasy environment of the oven cavity, it endures far more thermal stress than most electronic components ever will.

an electrical device with wires attached to the back of it, on a white background
an electrical device with wires attached to the back of it, on a white background
Igniter Kit
Igniter Kit
Igniter Electrode for a Gas Grill
Igniter Electrode for a Gas Grill

Reaching it usually means removing the oven racks, pulling the bottom oven panel or storage drawer, and sometimes working through the rear access panel. On some models, the igniter is accessible from inside the oven after removing a single retaining screw and a cover plate; on others, the burner assembly must be loosened first. Knowing which style your model uses before ordering parts prevents the frustration of discovering you need additional hardware halfway through the job.

Why Current Draw Matters More Than the Glow

Here is the single most misunderstood fact about this part: an igniter that glows is not necessarily an igniter that works. Over hundreds of heating cycles, the ceramic element erodes and its electrical resistance rises. As resistance climbs, the current it draws falls. Eventually the current drops below the threshold needed to hold the gas safety valve open, so the igniter glows brightly while the oven stays cold and no gas ever reaches the burner.

AD

That is why a technician reaches for a clamp meter rather than simply eyeballing the glow. Measuring the current through the igniter circuit and comparing it against the specification for the appliance tells you definitively whether the igniter is capable of doing its job. If the reading is low, replacing the igniter restores the circuit. If the reading is within spec but the burner still will not light, the fault lies elsewhere — most commonly with the safety valve, the thermostat, or the control board, and replacing the igniter in that scenario accomplishes nothing.

NTI 83724-1 SPARK IGNITER WITH 12 WIRE
NTI 83724-1 SPARK IGNITER WITH 12 WIRE
MHP GGEIB-SET Complete Electronic Ignitor Set
MHP GGEIB-SET Complete Electronic Ignitor Set
DIY Electric Igniters for Rocket Engines & Pyrotechnics - ELEMENTALMAKER
DIY Electric Igniters for Rocket Engines & Pyrotechnics - ELEMENTALMAKER
W357-0006 Ignitor
W357-0006 Ignitor
Ignited - Decreelife
Ignited - Decreelife
Copeland White-Rodgers Hot Surface Ignitor, Silicon Carbide 767A-383 - The Home Depot
Copeland White-Rodgers Hot Surface Ignitor, Silicon Carbide 767A-383 - The Home Depot

Compatibility, Cross-References, and Choosing the Right Part

The igniter 316489403 is used across a wide range of gas ranges manufactured under the Electrolux umbrella, which includes Frigidaire, Kenmore, Gibson, Tappan, White-Westinghouse, and several other badges applied to the same underlying platforms. That shared lineage is convenient for parts availability, but it also creates confusion, because visually similar igniters with different part numbers can have different amp ratings, bracket shapes, and connector styles.

Parts catalogs frequently list this number alongside superseded or cross-referenced numbers, which means an older part may have been replaced by 316489403 or the reverse. Before purchasing, always confirm fit using the full model number printed on the appliance's rating plate rather than the series name or the number stamped on the old igniter alone. A parts supplier with a reliable model-number lookup will save you a return shipment.

AD

Verifying Fit Before You Order

The rating plate on most ranges is located in one of a few predictable places: inside the storage drawer or broiler drawer, on the frame behind that drawer, on the back of the unit, or occasionally inside the oven door frame. Photograph it with your phone so you have the complete model and serial information on hand while shopping. Serial numbers also help identify production runs that may have used different components mid-cycle.

Igniter
Igniter
16170 24" IGNITER WIRE WITH BEND, TXBQ
16170 24" IGNITER WIRE WITH BEND, TXBQ

Once you have the model number, compare four physical details against the listing: the connector type and pin count, the mounting bracket configuration, the length of the wire leads, and the rated current. A part can look identical at a glance and still be wrong. If you are unsure, choose a supplier with a clear return policy, because a restocking fee on a mis-ordered igniter can cost nearly as much as the part.

OEM Versus Aftermarket Igniters

Original equipment igniters are built to the manufacturer's specification and usually carry a longer warranty, but they cost more. Aftermarket replacements from established brands are often functionally equivalent and considerably cheaper, and many are manufactured in the same facilities that supply the OEM channels. The differences tend to show up in ceramic quality, element longevity, and the robustness of the wire insulation.

AD

If you plan to keep the range for years, a quality OEM or premium aftermarket igniter is the safer long-term investment, since the labor of replacement is identical either way and a prematurely failed element means doing the job twice. Avoid unbranded listings with no current rating, no warranty, and no clear photo of the connector, as those parts frequently arrive with mismatched hardware that forces improvisation during installation.

Replacing the Igniter 316489403 Safely

Before any work begins, disconnect the range from electrical power at the breaker or unplug the cord, and shut off the gas supply at the wall valve behind the appliance. Let the oven cool completely — the igniter and burner area retain heat long after the display goes dark. Work in a well-lit space with the floor protected, since oven interiors shed crumbs, grease, and occasionally small screws that are easy to lose.

Gather a nut driver or socket set, a Phillips and flathead screwdriver, a flashlight or headlamp, and a clamp meter if you plan to verify the circuit afterward. Take a photo of the existing wiring before disconnecting anything, especially if the connector orientation is ambiguous. Pay attention to how the old igniter's leads are routed; the new part must follow the same path so it does not contact the burner or the oven floor.

Step-by-Step Removal and Installation

The general sequence is consistent across most models that use this igniter, though the exact panel removal varies. The key principle is to move patiently, because the ceramic element is fragile and the surrounding sheet metal has sharp edges.

  1. Remove the oven racks, then take out the bottom oven panel or open the storage drawer to expose the burner area.
  2. Locate the igniter bracket, usually held by one or two screws, and remove them carefully.
  3. Disconnect the igniter's wire connector, pulling on the plug body and never on the wires themselves.
  4. Withdraw the old igniter, noting how the leads were routed and how the bracket sat against the burner tube.
  5. Position the new igniter 316489403 in the same orientation and hand-thread the mounting screws before tightening.
  6. Reconnect the wiring harness plug until it clicks or seats fully, then tug gently to confirm engagement.
  7. Reinstall the oven panel or drawer, restore gas and power, and test a bake cycle.

One installation warning deserves emphasis: never touch the gray or black tip of a new igniter with bare fingers. Skin oils can create hot spots that shorten the element's life or cause it to crack on the first heating cycle. Handle the new part by its base or bracket, and keep it in its packaging until the moment it goes in.

Testing the New Igniter After Installation

Restore the gas valve and power, then set the oven to bake at a moderate temperature such as 350 degrees. Within roughly 30 to 60 seconds, the igniter should glow bright orange, followed shortly by the sound of gas igniting and a steady flame along the burner tube. If the igniter glows but no flame appears, shut the oven off immediately and re-check the connector, the valve, and the current draw rather than repeatedly cycling the appliance.

If you have a clamp meter, confirm the current reading falls within the range specified for your model, which for this style of igniter is commonly in the range of roughly 2.5 to 3.6 amps depending on the platform. A reading well below spec on a brand-new part usually points to a wiring or valve problem rather than a defective igniter. Once the oven heats and holds temperature through a full cycle, the repair is complete and the range can return to normal use.

The igniter 316489403 is a modest part with an outsized role in how a gas oven behaves, and understanding its dual job as both ignition source and current-sensing link in the safety circuit makes diagnosis far less mysterious. Keep the old part's model information and your purchase receipt filed away, since a warranty claim is much easier with documentation on hand, and consider noting the installation date inside the appliance manual. With a correct diagnosis and careful handling, most homeowners can complete this repair in under an hour and get back to baking without a service call.

AD