DIY Shower Renovation: Replacing a Shower Faster and Cheaper
Refreshing your bathroom can significantly boost your home's appeal, and giving your shower a makeover is a great starting point. But, you don't have to spend a fortune hiring professionals. With the right tools and a bit of elbow grease, you can redo your shower yourself. Here's a step-by-step guide to help you achieve a stunning, professional-looking result.
Before we dive into the project, let's talk about safety. Ensure you're working in a well-ventilated area, wear appropriate personal protective equipment, and always turn off the main water supply before starting any work. Now, let's get started!
Planning Your Shower Redo
Planning is key to any successful DIY project. First, decide on the look and feel you want for your shower. Pinterest and home improvement websites offer plenty of inspiration. Consider materials like tiles, fixtures, and shower pans, and choose a design that suits your home and your budget.



Next, gather all the necessary tools and materials. This could include tiles, grout, thinset mortar, a trowel, a tile saw, a level, a rubber mallet, caulk, waterproof membrane, and of course, safety gear like gloves, safety glasses, and a dust mask. It's also a good idea to have a helping hand for this project, so enlist a friend or family member to lend a hand.
Demolition: Removing Old Tile and Fixtures
begin by turning off the water supply and disconnecting any plumbing. Then, carefully remove the old tiles and fixtures. Start from one end of the shower and work your way across to avoid damaging more tiles than necessary. Use a utility knife to score the tiles and a hammer to break them into smaller pieces for easier removal. Don't forget to wear safety glasses and gloves to protect yourself from debris.



Once the tiles are gone, remove any remaining thinset or mortar. You may need to use a chisel or a rented angle grinder to get the job done. Be careful not to damage the wall studs behind the tiles. Finally, clean up any remaining debris and prepare the surface for new tiles.
Installing the Shower Pan
Before laying new tiles, you'll need to install a shower pan. A shower pan is a watertight base that prevents water from leaking onto the floor below. If replacing an existing pan, remove the old one and any remaining caulk or sealant. Clean the area thoroughly and ensure the subfloor is level and structurally sound. Then, install the new shower pan according to the manufacturer's instructions.
Apply a waterproof membrane to the walls and floor of the shower area. This will prevent water from penetrating the walls and causing damage. Again, follow the manufacturer's instructions for application. Finally, prime the area using a primer designed for shower applications. This will help seal the surface and prepare it for tiling.






Laying New Tile: The Backbone of Your Shower
Now, it's time to lay the new tiles! This step requires patience and careful measurement to ensure a straight, even layout. Start by marking a guideline on the wall and floor using a level to ensure your tiles are straight. Then, spread a thin layer of thinset mortar onto the wall or floor using your trowel.
Press the tiles firmly into the mortar, using spacers to ensure even gaps between each tile. Work your way up the wall, using a level to ensure each row is straight. If you need to cut tiles to fit around fixtures or edges, use a tile saw to make clean, precise cuts. Allow the mortar to set for the recommended time before removing the spacers.
Grout Application: The Final Touch
After the mortar has set, it's time to apply grout. Mix the grout according to the manufacturer's instructions, and use a grout float to spread it evenly between the tiles. Work diagonally across the tiles to ensure the grout fills the joints completely. Allow the grout to set for about 15 minutes, then use a damp sponge to clean off any excess grout from the tile surface.

Repeat this process, cleaning with a damp sponge and turning it to a clean side each time, until you've cleaned all of the grout from the tile surface. Allow the grout to set for the recommended time before sealing it with a silicone-based sealant. This will help protect the grout and make it easier to clean.
Installing Fixtures and Reconnecting Plumbing
Once the grout is completely dry, you can install any new fixtures, such as showerheads, faucets, and hardware. Be sure to reconnect the plumbing and turn the water supply back on slowly to avoid any leaks. Check for leaks by running water through the shower and checking all connections.
Finally, apply caulk along the edges of the shower pan and any vertical surfaces to seal them and prevent water from entering. Allow the caulk to dry completely before using the shower.
Congratulations! You've just redoing your shower like a pro. Enjoy your new space, and don't forget to maintain it by cleaning your shower regularly to keep mold and mildew at bay. Happy showering!



