Hayward W400BWHP Pool Heat Pump: Powerful, Efficient Heating for Large Pools
The Hayward W400BWHP is a pool filtration system built around the trusted Perflex extended-cycle D.E. filter design. It is aimed at pool owners who want very fine filtration, less frequent backwashing, and a straightforward maintenance routine. If you are researching this model, you are likely trying to decide whether its 40-square-foot DE filter and packaged pump setup are right for your pool. This guide covers how the system works, how to size it, and what it takes to keep it running cleanly.
Unlike a basic sand filter, the Hayward W400BWHP uses diatomaceous earth to capture particles that are often too small for other filter types. That can translate into noticeably clearer water, fewer cloudy days, and less strain on your pool chemistry. The “P” in the model name generally points to a package that includes a matched pump, so you are not just buying a filter tank. You are buying a more complete filtration solution that can simplify equipment selection.
What the Hayward W400BWHP Filter System Does
The heart of the Hayward W400BWHP is a Perflex D.E. filter with roughly 40 square feet of effective filtration area. Water is pulled from the pool by the pump, pushed through the filter, and returned to the pool through the return fittings. Inside the filter, DE powder coats flexible tubes and creates a fine screening layer that traps dirt, oils, and microscopic debris.
Because DE filtration is so fine, the system is often chosen by pool owners who are tired of hazy water or frequent cartridge cleaning. The filter’s job is not just to remove leaves and bugs; it also helps polish the water by catching particles that can make a pool look dull. That polishing effect is one of the main reasons the Perflex design has remained popular for decades.
Perflex Extended-Cycle D.E. Technology
Perflex is Hayward’s name for an extended-cycle D.E. design. Instead of backwashing every time the pressure gauge rises, the filter uses flexible tubes and a bump handle to shake loose the collected DE and debris. The debris settles at the bottom of the tank, and the tubes are recoated as the system continues to run. This allows longer intervals between full cleanings.
The extended-cycle feature is a big deal for water conservation. Traditional backwashing can send hundreds of gallons of pool water down the drain over a season. With the Hayward W400BWHP, you bump the handle when pressure climbs, and you only backwash when bumping no longer brings the pressure down effectively. That can save water while still keeping filtration performance high.
The Bump Handle and How Regeneration Works
The bump handle is the signature feature of the Hayward W400BWHP. When the pressure gauge reads about 8 to 10 PSI above the clean starting pressure, you turn off the pump. Then you push the bump handle down and let it snap back up several times. This flexes the filter tubes and dislodges the debris layer that has built up on the surface.
After bumping, restart the pump and check the pressure. If it drops back near the clean baseline, the filter has regenerated and can continue running. If pressure stays high after several bump cycles, it is time to backwash, drain the tank, and recharge it with fresh D.E. powder. This simple rhythm is why many pool owners prefer Perflex over other DE filter styles.
Sizing, Installation, and Long-Term Maintenance
A Hayward W400BWHP is not a one-size-fits-all system. The 40-square-foot filter and matched pump are best suited to certain pool volumes, plumbing layouts, and debris loads. Before buying, compare your pool’s gallonage, desired turnover rate, and existing equipment. The right match gives you clear water, reasonable run times, and less wear on the pump.
Installation also matters. The system needs a level pad, correct plumbing unions, and a safe electrical connection for the pump. If you are replacing an old filter, you may need to adjust plumbing to fit the W400BWHP’s ports and footprint. Planning the install before cutting pipes will save time, money, and frustration.
Matching the W400BWHP to Your Pool
The Hayward W400BWHP is often recommended for above-ground pools and smaller in-ground pools. With a 40-square-foot DE filter and a pump in the 1 HP range, it can handle many pools up to approximately 20,000 to 25,000 gallons, depending on bather load, climate, and daily run time. Larger pools or heavy-use pools may need a bigger filter system.
You should also consider your pump’s flow rate. A Perflex 40-square-foot filter has a design flow rate around 40 GPM, so a pump that pushes significantly more than that may overwhelm it. Matching the pump to the filter protects the internal tubes and helps the system run at the proper pressure. If you already own a high-flow pump, check the filter’s maximum flow rating before pairing it.
Routine Care and Troubleshooting
Routine care for the Hayward W400BWHP is straightforward: watch the pressure gauge, bump the handle when needed, and backwash when bumping stops working. You should also inspect the pump basket, skimmer baskets, and return flow every week. Keeping debris out of the pump reduces strain on the entire filtration system.
Common issues include low flow, high pressure, DE powder returning to the pool, and air bubbles in the pump basket. Low flow often points to a clogged impeller or a suction leak. High pressure usually means the filter needs bumping or backwashing. DE returning to the pool can indicate a torn tube, a bad gasket, or an incorrect recharge amount. Most problems are fixable with basic tools and a little patience.
If you are ready to enjoy clearer water with less backwashing, the Hayward W400BWHP deserves a close look. Check your pool’s size, confirm the pump match, and build a maintenance routine around the pressure gauge. With proper installation and care, this Perflex system can deliver dependable filtration season after season, leaving you more time to swim and less time fussing with equipment.