frigidaire compressor start relay

Frigidaire Compressor Start Relay: Fix Your Fridge Fast & Keep It Cool

By Andrew Wilson
AD

If your Frigidaire refrigerator has stopped cooling and you hear a repeated clicking sound near the back, the Frigidaire compressor start relay is one of the first components to investigate. This small but important part helps the compressor motor start and run efficiently, and when it fails, the refrigerator may appear completely dead even though lights and fans still work. Understanding how the start relay operates can save you from replacing a compressor that may still be in good condition.

The Frigidaire compressor start relay is an inexpensive repair compared with a sealed system or compressor replacement, which makes accurate diagnosis essential. Many homeowners assume the worst when the compressor hums briefly and then clicks off, but the relay, overload protector, or run capacitor is often the real culprit. A careful inspection and a few multimeter tests can reveal whether the relay is the source of the problem.

What a Frigidaire Compressor Start Relay Does

The start relay is mounted on the side of the compressor and acts as an electrical switch for the start winding. A single-phase compressor needs help creating the rotating magnetic field required to begin turning, and the relay briefly sends current through the start winding to create that phase shift. Once the compressor reaches normal speed, the relay removes the start winding from the circuit and lets the run winding keep the motor turning.

AD
LCTC Refrigerator Starter Relay For Fridge Spare Parts Compressor Cooling Relay Large Capacity RP-4
LCTC Refrigerator Starter Relay For Fridge Spare Parts Compressor Cooling Relay Large Capacity RP-4
Refrigerator Compressor Start Relay DA35-10013N
Refrigerator Compressor Start Relay DA35-10013N
Frigidaire Genuine OEM 5304413178 Refrigerator Compressor Start Relay, Black
Frigidaire Genuine OEM 5304413178 Refrigerator Compressor Start Relay, Black

Many Frigidaire refrigerators use a PTC, or positive temperature coefficient, start relay combined with an overload protector. The overload protector opens the circuit if the compressor draws too much current or gets too hot, preventing damage to the motor windings. Because these parts are often sold together or mounted as one assembly, technicians usually replace the relay and overload as a matched set when one fails.

How the Start Relay Works With the Compressor

Inside a PTC start relay, a small ceramic thermistor changes resistance as it heats up. When the refrigerator thermostat calls for cooling, current flows through the thermistor and into the compressor start winding. The thermistor heats quickly, its resistance rises sharply, and the start winding drops out of the circuit. A current relay works differently by using a magnetic coil to pull contacts open once the compressor draws normal running current.

Frigidaire Genuine OEM 216954236 Freezer Compressor Start Relay, White
Frigidaire Genuine OEM 216954236 Freezer Compressor Start Relay, White
the capacitor start capacitor run is located in this diagram, and it shows
the capacitor start capacitor run is located in this diagram, and it shows
Domestic Refrigerator Starting Relays
Domestic Refrigerator Starting Relays

If the relay sticks open, the compressor cannot start and may only hum or click. If it sticks closed, the start winding remains energized too long, causing the compressor to overheat and trip the overload protector. Frigidaire models may use different relay styles depending on compressor size and production year, so the replacement must match the refrigerator model and compressor label. A relay that looks similar but has different electrical characteristics can cause repeat failures or poor cooling.

Common Symptoms of a Bad Start Relay

One of the most common signs is a clicking noise every few minutes followed by silence, with the refrigerator failing to cool. The interior lights may work, the evaporator fan may run, and the condenser fan may spin, but the compressor never stays on long enough to build cold temperatures. You may also notice that the freezer is slightly cool while the fresh food section is warm, or that the compressor feels hot to the touch.

AD

Physical clues include a rattling sound when the relay is shaken, burn marks on the plastic housing, a melted terminal, or a burnt electrical smell near the compressor. However, these symptoms can also point to a failed run capacitor, a weak overload protector, or a compressor with bad windings. That is why testing the relay and the compressor circuits before ordering parts prevents unnecessary repairs and wasted money.

an image of the components for a car
an image of the components for a car
a man fixing an air conditioner in a room
a man fixing an air conditioner in a room
How to replace a freezer compressor start relay | Repair guide
How to replace a freezer compressor start relay | Repair guide
Frigidaire Refrigerator Not Cooling This Finally Fixed It
Frigidaire Refrigerator Not Cooling This Finally Fixed It
Frigidaire 5304491941 Refrigerator Start Device
Frigidaire 5304491941 Refrigerator Start Device
How to Test & Replace the Compressor Start Relay in a Refrigerator | Repair & Replace
How to Test & Replace the Compressor Start Relay in a Refrigerator | Repair & Replace

Testing and Replacing the Frigidaire Start Relay

Before any testing begins, unplug the refrigerator from the wall outlet. The compressor and relay area can have line voltage, and the capacitor, if present, may hold a charge even after power is removed. Pull the refrigerator away from the wall, remove the rear access panel, and locate the black or gray relay assembly attached to the side of the compressor. Take a photo of the wire connections before removing anything.

Replacement relays for Frigidaire refrigerators are widely available online and through appliance parts stores, but the model number and compressor information must be matched carefully. In many cases, the original relay has been superseded by an updated kit that includes a new overload protector and wire harness. If the compressor windings are shorted or open, replacing the relay will not restore cooling, so testing should always include the compressor terminals and the run capacitor.

AD

How to Test the Relay Safely

After unplugging the refrigerator and removing the relay, inspect it for cracks, discoloration, or a loose fit on the compressor pins. Shake the relay gently; if it rattles, internal pieces may have broken apart. Set a multimeter to the ohms scale and test the relay terminals according to the manufacturer's diagram. A good PTC relay often shows a low resistance reading when cool, while an open or shorted reading indicates failure. Current-type relays should show continuity through the coil, but exact values vary by part number.

Refrigerator Compressor Start Relay 5304508629 For Electrolux, Frigidaire, Whit
Refrigerator Compressor Start Relay 5304508629 For Electrolux, Frigidaire, Whit
Fridge Compressor Not Starting Replace Start Relay & Overload
Fridge Compressor Not Starting Replace Start Relay & Overload

Test the compressor windings by measuring resistance between the common, start, and run terminals. You should find measurable resistance between common and start and between common and run, with the highest reading between start and run. An infinite reading means an open winding, while a reading near zero suggests a short. If the compressor tests good and the relay tests bad, replace the relay and overload protector. If the compressor tests bad, a qualified technician should evaluate the sealed system.

Step-by-Step Replacement Tips

Purchase the correct Frigidaire compressor start relay for your model, then discharge any capacitor before touching the terminals. Remove the old relay from the compressor pins, transfer the wires one at a time to the new relay, and match the orientation of the original part. Push the new relay firmly onto the compressor terminals until it seats completely, then reconnect the overload protector and mounting clip. Reinstall the rear panel and wait at least ten minutes before plugging the refrigerator back in.

AD

When power returns, listen for a smooth compressor start rather than a loud hum or repeated click. Let the refrigerator run for several hours and check both the freezer and fresh food temperatures. If the compressor still clicks or trips the overload, test the run capacitor and verify that house voltage is stable. Never bypass the overload protector, because it protects the compressor from dangerous current levels. If the relay fails again quickly, the compressor may be drawing excessive current or the replacement part may be incorrect.

When your Frigidaire refrigerator is warm and the compressor area is clicking, a failed start relay is a practical and affordable first suspect. Confirm the model number, inspect the old relay, test the compressor windings, and install the correct replacement rather than forcing a universal part to fit. With the right diagnosis and a little patience, you can restore reliable cooling and avoid the cost of a compressor replacement. Keep the old part and your notes handy, because knowing what failed can make the next repair faster and more confident.

AD