emt bending cheat sheet

EMT Bending Cheat Sheet: Master Conduit Bends Fast

By Kevin Martinez
AD

An EMT (electrical metallic tubing) bending cheat sheet is the pocket-sized field guide that turns conduit bending from guesswork into repeatable geometry. Whether you are running 1/2-inch EMT in a commercial ceiling or bending 1-inch conduit for a service rack, the right numbers help you create accurate 90s, offsets, and saddles without wasting material.

This guide breaks down the most useful EMT conduit bending values, including take-up, deduct, multipliers, shrink, and saddle layouts. Keep it with your hand bender or electric bender notes, and always confirm the numbers against your specific bender manufacturer because take-up and degree marks can vary slightly.

Core Numbers Every EMT Bending Cheat Sheet Should Include

Every reliable EMT bending cheat sheet starts with the measurements stamped or implied by the bender. Hand benders use an arrow, star, and degree markings, while electric benders may use shoes, follow bars, and digital readouts. The constants below are typical for common EMT sizes, but they are not universal across every brand.

AD
the metal sheet is labeled with instructions for how to install and use it in this project
the metal sheet is labeled with instructions for how to install and use it in this project
a diagram showing the different types of bendings
a diagram showing the different types of bendings
EMT Fittings
EMT Fittings

Before bending a full run, test a scrap piece. A quick test bend reveals the actual take-up, deduct, and shrink for your bender, pipe, and technique. That single habit prevents expensive rework and makes your cheat sheet truly trustworthy.

Take-Up, Deduct, and 90-Degree Stub Bending

Take-up is the distance from the arrow mark on a hand bender to the back of a 90-degree bend. For many 1/2-inch EMT hand benders, take-up is about 5 inches; 3/4-inch models often use 6 inches; and 1-inch models commonly use 8 inches. The deduct for a 90-degree stub is typically the same as the take-up, so you subtract that value from the desired stub length before marking the conduit.

Electrical Conduit Bending Quick-Card : A Unique Quick-Reference Guide by Builder's Book Inc. (2011, Stapled) for sale online | eBay
Electrical Conduit Bending Quick-Card : A Unique Quick-Reference Guide by Builder's Book Inc. (2011, Stapled) for sale online | eBay
the basics of bbs bar bending schedule is shown in blue and has instructions for how to
the basics of bbs bar bending schedule is shown in blue and has instructions for how to
the back side of a cell phone with text on it and an image of two different buttons
the back side of a cell phone with text on it and an image of two different buttons

For example, if you need a 12-inch stub using a bender with a 5-inch take-up, measure 12 inches from the end of the conduit, subtract 5 inches, and mark at 7 inches. Align the arrow with that mark, keep the conduit flat in the bender, and bend to 90 degrees. For back-to-back 90s, the star mark is commonly used, but confirm the correct mark on your bender because some manufacturers label them differently.

Offset Multipliers and Shrink Constants

Offsets are where an EMT bending cheat sheet becomes especially valuable. To find the distance between bends, multiply the offset depth by the multiplier for your bend angle. Common multipliers are 10 degrees = 5.76, 22.5 degrees = 2.61, 30 degrees = 2.0, 45 degrees = 1.41, and 60 degrees = 1.15. A 30-degree offset is popular because the math is simple and the bend is easy to control.

AD

Shrink is the amount the conduit effectively shortens after bending an offset. Typical shrink constants per inch of offset depth are 10 degrees = 1/16 inch, 22.5 degrees = 3/16 inch, 30 degrees = 1/4 inch, 45 degrees = 3/8 inch, and 60 degrees = 1/2 inch. If you need a 2-inch offset at 30 degrees, the distance between marks is 2 x 2 = 4 inches, and the shrink is 2 x 1/4 = 1/2 inch. Add that shrink to your measurement when the offset must land at a specific point.

an image of a spreadsheet with numbers and symbols
an image of a spreadsheet with numbers and symbols
sheet metal quick reference guide with instructions to make it easier for you to learn how to use
sheet metal quick reference guide with instructions to make it easier for you to learn how to use
📋 Bar Bending Schedule (BBS) Explained | Civil Engineering Guide
📋 Bar Bending Schedule (BBS) Explained | Civil Engineering Guide
Offset Bends
Offset Bends
Elliott Electric Supply - Lower Cost, Quality Electrical Supplies, and Personal Service
Elliott Electric Supply - Lower Cost, Quality Electrical Supplies, and Personal Service
Types of Electrical Conduit | Electrical Wiring Installation Quick Guide
Types of Electrical Conduit | Electrical Wiring Installation Quick Guide

Field-Ready EMT Bending Cheat Sheet Applications

A cheat sheet is most useful when it supports the actual sequence of field work: measure, mark, align, bend, and verify. The numbers matter, but so does the order of operations. Rushing the marking stage or forgetting shrink can throw off an entire rack, especially when multiple conduits must run parallel and enter the same box.

Use your EMT conduit bending notes for common bends first, then add project-specific reminders. For instance, note the bender model, the actual take-up you measured, and any angles your crew prefers. A personalized cheat sheet beats a generic one because it reflects the tools in your truck and the conditions on your job site.

AD

Back-to-Back, Stub, and Kicks

Back-to-back bends require you to measure from the back of one 90 to the back of the next. On many hand benders, the star is the reference mark for back-to-back bends, while the arrow is used for stubs. Keep the first bend oriented correctly, then rotate the conduit so the second bend meets the required spacing without twisting the run.

Ecg Lead Facing Guide, 12 Lead Ekg Placement Cheat Sheets, 12 Lead Ekg, Difference Between Ecg And Ekg, Ecg Pocket Guide Download, Pr Interval Ecg Diagram, 12 Lead Ekg Pocket Guide, Ekg Electrode Placement, Evidence-based Ekg Interpretation
Ecg Lead Facing Guide, 12 Lead Ekg Placement Cheat Sheets, 12 Lead Ekg, Difference Between Ecg And Ekg, Ecg Pocket Guide Download, Pr Interval Ecg Diagram, 12 Lead Ekg Pocket Guide, Ekg Electrode Placement, Evidence-based Ekg Interpretation
two tables with different types of multiplierrs for each type of object in the table
two tables with different types of multiplierrs for each type of object in the table
a drawing of different types of pipes and fittings on a piece of lined paper
a drawing of different types of pipes and fittings on a piece of lined paper
EMT Bending: How To Make a 3 Point Saddle Bend Without Charts or Apps
EMT Bending: How To Make a 3 Point Saddle Bend Without Charts or Apps

Kicks are small offsets, often at the end of a run, used to shift conduit slightly to meet a box, coupling, or wall condition. A 10-degree or 22.5-degree kick is common because it is subtle and easy to adjust. Use the offset multiplier and shrink from your cheat sheet, but remember that a kick usually needs only one or two bends, so mark clearly and avoid over-bending.

Three-Point and Four-Point Saddles

A three-point saddle is used to route EMT over an obstruction such as a pipe or beam. A typical layout uses a 45-degree center bend and two 22.5-degree outer bends. Mark the center of the obstruction, then measure outward using a saddle multiplier, often about 2.5 times the saddle depth, to locate the outer marks. Shrink for a three-point saddle is commonly estimated at 3/16 inch per inch of depth, but verify with a test bend.

AD

Four-point saddles use four bends and are useful when you need a flatter top or more gradual transitions. They often combine 22.5-degree and 45-degree bends, depending on the depth and the look you want. The safest approach is to mark the center, lay out the two inner bends, then place the two outer bends so the saddle sits level and centered over the obstruction. Keep your EMT bending cheat sheet updated with the exact saddle layout that works with your bender.

A good EMT bending cheat sheet lives in your pouch, your phone, or the lid of your tool box, ready for the next run. Practice each bend on scrap, record your actual numbers, and soon the multipliers will become second nature. The more you verify and adjust, the faster you will bend clean, professional conduit that fits right the first time.

AD