electrical knockout

Electrical Knockout 101: Types, Sizes, and How to Use Them Safely

By Emily Walker
AD

An electrical knockout is one of those small details that most people never notice until it becomes a problem. If you have ever looked at the side of a metal junction box, a load center, or a piece of rigid conduit and seen a circular disc stamped into the steel, you have already met one. That pre-scored circle exists so an electrician can open a clean, correctly sized hole for a conduit fitting, cable connector, or cord grip without drilling into the enclosure in the field.

The concept sounds simple, but the knockout touches nearly every part of an electrical installation: box fill calculations, grounding and bonding, weather resistance, wire insulation protection, and code compliance all depend on how well those openings are created or closed. Understanding the different types, sizes, and removal methods helps you work faster and avoid the kind of mistakes that turn into inspection failures or damaged conductors down the road.

What Exactly Is an Electrical Knockout?

An electrical knockout, often abbreviated as KO on drawings and job sites, is a removable section of metal or plastic built into an enclosure during manufacturing. It is formed by a partial die cut, scoring, or a series of tiny webs that hold the disc in place while keeping the enclosure rigid. When a raceway or cable needs to enter, the installer removes the disc with hand tools or a punch, leaving an opening sized to match a standard conduit trade size.

AD
electrokinesis
electrokinesis
two air conditioners are attached to the side of a brick wall in an abandoned building
two air conditioners are attached to the side of a brick wall in an abandoned building
☆ ° ೃ 𝑳𝒐𝒕𝒖𝒔. ❀
☆ ° ೃ 𝑳𝒐𝒕𝒖𝒔. ❀

Knockouts are not just convenient holes. They are engineered features that keep an enclosure listed and rated. Removing the correct knockout preserves the structural integrity of the box, maintains its UL listing for the environment it was designed for, and gives the fitting a flush surface to seat against so bushings and locknuts clamp properly. Punching your own hole with a hole saw usually voids nothing on a standard sheet metal box, but it can compromise a weatherproof rating on a gasketed enclosure if the hole is not sealed correctly.

The Anatomy of a Knockout

On a typical stamped steel box, a knockout consists of a circular disc connected to the surrounding metal by three or four narrow bridges of steel. These bridges act as shear points. A small slot or dimple near the edge of the disc gives a screwdriver blade something to bite into, so the disc can be pried away with a rocking motion. The remaining opening often has a slight lip, which helps the fitting self-center as it is tightened.

Anthony Joshua knocks out Wladimir Klitschko in 11th round
Anthony Joshua knocks out Wladimir Klitschko in 11th round
Omega & Knockout
Omega & Knockout
two electrical outlets are shown in an old fashioned style wall outlet cover with rust on them
two electrical outlets are shown in an old fashioned style wall outlet cover with rust on them

Larger enclosures frequently use concentric knockouts, which are multiple rings nested inside one another. A single stamped feature might allow a 1/2 inch, 3/4 inch, and 1 inch entry depending on which rings you remove. Older or industrial equipment may use eccentric knockouts, where the rings share an outer edge rather than a common center. Eccentric designs exist because they let manufacturers fit large openings into a limited face area, but they require extra care when bonding, since the remaining rings can interfere with standard locknuts.

Knockouts Compared with Other Entry Methods

Not every enclosure ships with knockouts. Cast aluminum boxes, stainless steel control enclosures, and many NEMA 4X or explosion-proof housings are often supplied as blank bodies with no openings at all. In those cases, the installer drills or punches a hole and uses a sealing fitting or hub to maintain the enclosure rating. The difference matters because a knockout is a factory-controlled opening with a known diameter and wall thickness, while a field-drilled hole depends entirely on the tool and the operator.

AD

Plastic boxes are a separate case. Many PVC and fiberglass enclosures use molded knockouts that snap out cleanly by hand or with light pliers pressure. These are convenient but fragile; over-prying can crack the surrounding wall and ruin the box. Always check whether the manufacturer specifies a maximum fitting size for each molded KO, because the wall thickness of a plastic box is far less forgiving than steel when a heavy fitting is torqued down.

knockout Icon 🍒
knockout Icon 🍒
an anime character with the words knock out in front of him and his head on top of
an anime character with the words knock out in front of him and his head on top of
a person holding their hand up to the camera with an electric discharge coming out of it
a person holding their hand up to the camera with an electric discharge coming out of it
a man laying on the ground in front of some electrical wires
a man laying on the ground in front of some electrical wires
an illustration of a hand with lightning bolts coming out of it on a pink background
an illustration of a hand with lightning bolts coming out of it on a pink background
lightning striking through the dark sky above a tower with two lights on top and one in the middle
lightning striking through the dark sky above a tower with two lights on top and one in the middle

Knockout Sizes, Standards, and Code Rules

One of the most common points of confusion for apprentices is that knockout sizes do not match the actual diameter of the hole. A 1/2 inch knockout is not half an inch wide. The number refers to the trade size of the conduit or fitting the opening is designed to accept, not the physical opening itself. The actual hole is always larger, because the trade size describes the nominal internal diameter of the raceway, not its outside dimension or the opening that receives a connector.

Keeping a mental chart of these dimensions saves a lot of trips back to the truck. It also helps when you are verifying that a replacement cover, a blank plate, or a sealing gasket will actually fit an existing opening in equipment you did not install yourself.

AD

Common Trade Sizes and Their Measurements

The table below lists typical knockouts found on standard sheet metal boxes, load centers, and wireways. Exact dimensions vary slightly between manufacturers and between punch sets, so treat these as working approximations rather than precision machining tolerances.

Kevin Holland Talks KOs Joaquin Buckley
Kevin Holland Talks KOs Joaquin Buckley
Lightning Collision Powerful by Yummybuum | Creative Market
Lightning Collision Powerful by Yummybuum | Creative Market
an animated image of a red and black robot
an animated image of a red and black robot
Electrical Short Circuit at a Power Station
Electrical Short Circuit at a Power Station

If a fitting is loose in the opening, the wrong knockout was likely removed, or the disc was torn rather than sheared cleanly. A torn opening will not let a locknut seat flat, which can lead to a poor bond and a loose connection that vibrates over time.

Trade SizeTypical Knockout Diameter
1/2 inchAbout 7/8 inch (22 mm)
3/4 inchAbout 1-1/8 inch (28 mm)
1 inchAbout 1-3/8 inch (35 mm)
1-1/4 inchAbout 1-11/16 inch (43 mm)
1-1/2 inchAbout 1-15/16 inch (49 mm)
2 inchAbout 2-7/16 inch (62 mm)

NEC Requirements for Openings and Unused Holes

The National Electrical Code addresses knockouts in several places, and the most frequently cited rule is the one about unused openings. Section 110.12(A) requires that unused openings in enclosures be closed in a manner that provides protection substantially equivalent to the wall of the equipment. In plain language, you cannot leave an open knockout on a panel, box, or motor housing. It must be covered with a listed blank plate, plug, or sealing fitting that fits that specific opening.

AD

Grounding rules matter too. Where a metal raceway or cable connector is installed through a knockout, the connection must maintain electrical continuity. Standard locknuts and bushings provide that continuity on most enclosures, but concentric and eccentric knockouts may require bonding jumpers or listed bonding-type bushings because the remaining rings create a poor metal-to-metal path. Section 250.92 and related bonding provisions apply here, so when in doubt, use the fitting the manufacturer lists for that enclosure rather than improvising.

Tools and Techniques for Removing a Knockout

Removing a knockout is one of the first skills an electrician learns, and doing it cleanly is a mark of someone who takes pride in the trade. A torn, dented, or oversized opening is not just ugly; it can leave sharp edges that slice through conductor insulation during a wire pull. The goal is a sheared, burr-free hole that a fitting can sit in squarely.

Before you touch anything, de-energize the equipment and verify the absence of voltage. Knockouts on live panelboards and control cabinets are a genuine hazard, not only from shock but from the knife-like edges that tend to catch hands and forearms. Safety glasses and cut-resistant gloves are standard practice for this task.

Manual Knockout Removal with Hand Tools

The traditional method uses a flathead screwdriver and a pair of lineman's pliers. Set the tip of the screwdriver into the slot or against the edge of the disc and give it a firm, controlled tap or pry. The disc will usually break free along its bridge points, and the pliers are then used to rock the disc back and forth until it snaps out. Do not lever against the box wall, because that bends the enclosure and distorts the opening.

After the disc comes out, run your gloved thumb or a deburring tool around the rim. Any sliver of metal left behind should be filed or chamfered, especially if the opening will carry jacketed cable or individual conductors. A simple pass with a half-round file takes seconds and prevents a service call years later when a hot conductor grounds out against a sharp edge.

Punches, Step Bits, and Hydraulic Knockout Sets

When a box has no factory knockout, or when you need a hole in a thick enclosure or stainless steel, a knockout punch set is the right tool. These sets consist of a draw stud, a die, and a cutter. You drill a small pilot hole, insert the stud through the die and cutter, and tighten the assembly with a wrench, ratchet, or hydraulic pump until the cutter shears a clean circle through the metal. The result is a precise, round hole with a smooth wall.

Step bits and hole saws are common alternatives for plastic enclosures, small boxes, and field modifications where a punch set will not fit. Hole saws cut quickly but leave a rougher edge, and they can grab and spin the enclosure if it is not clamped down. Whichever method you choose, measure twice, confirm the fitting size, and account for enclosure depth. A beautifully cut hole in the wrong location is far more expensive to fix than the extra minute it takes to mark it out correctly.

Knockouts are a small feature with an outsized influence on how professional an installation looks and how long it survives. Learning to identify concentric and eccentric rings, matching trade sizes to the right fittings, and keeping a punch set within reach puts you in a position to handle whatever an enclosure throws at you. Next time you open a panel, take a second look at those stamped discs; they are a quiet reminder that good electrical work starts long before the first wire is pulled.

AD