Best Drill Bits for Brick: The Ultimate Guide to Choosing the Right Bit
Drilling into brick looks like a simple job until the bit skates across the surface, the tip turns blue, and the hole lands an inch away from your pencil mark. The difference between a clean, fast hole and a scarred wall almost always comes down to one decision: choosing the right drill bit for brick. Brick is abrasive, brittle, and wildly inconsistent — soft lime mortar can sit a few millimetres away from dense, fired clay that behaves almost like a low-grade concrete. Bits designed for timber or steel simply cannot cope with that mix.
What follows is a practical breakdown of how masonry bits work, how shank types change performance, which sizes match common wall plugs, and how to avoid the classic mistakes that crack bricks or destroy expensive tooling. Whether you are running a basic cordless combi drill or a dedicated SDS rotary hammer, the details below will help you drill straighter, faster, and with far less damage to the wall.
How Masonry Drill Bits Cut Through Brick
Traditional twist bits for wood shear away fibres, and bits for metal cut clean curls of steel. Masonry bits work differently. They are designed to pulverise a brittle material into dust, and they rely on impact as much as rotation. The flutes are wider and shallower than a metalworking bit so that abrasive brick dust can escape without clogging, and the tip is not sharp in the conventional sense — it is hard, and hardness is what matters.
That distinction explains why pushing harder rarely helps when drilling brick. If the bit is not hard enough or the drill is not delivering impact energy, extra pressure just generates heat. Heat softens the brazed joint holding the cutting tip, and once that tip dulls or spins loose, the bit is effectively scrap. Understanding the mechanical process makes it much easier to choose the right accessory and use it correctly.
Carbide Tips and Why Hardness Beats Sharpness
Almost every quality masonry bit uses a tungsten carbide tip brazed into a steel body. Tungsten carbide is extremely hard and retains that hardness even when it gets hot, which allows it to survive contact with silica-rich clay and mortar. The tip geometry is usually a shallow point with a defined cutting edge, and on better bits you will notice a slightly wider tip than the shank, which reduces friction against the sides of the hole.
Cheap bits often use a thinner carbide insert that wears quickly or a steel body that bends under load. If you are drilling hard engineering bricks or a lot of holes in one session, spending more on a branded bit with a properly ground tip pays for itself almost immediately. A dull bit needs more pressure, generates more heat, and produces a ragged, oversized hole that grips wall plugs poorly.
Shank Types: Round, Hex, and SDS-Plus
The shank is the part that goes into the chuck, and it dictates which tools you can use. Standard round shank bits fit a three-jaw keyless chuck and work in any cordless drill or combi drill. Hex shanks are common on smaller bits and offer better grip in quick-change chucks, reducing slippage when the bit bites into a hard surface. Both of these rely on the drill's hammer mechanism — if your drill has one.
SDS-Plus bits have shallow slots and grooves that lock into a dedicated rotary hammer chuck. They can slide axially inside the chuck, which allows the hammer piston to strike the bit directly rather than pushing the whole drill forward. The result is dramatically more efficient impact energy. If you plan to drill more than a handful of holes in brick or concrete, an SDS-Plus rotary hammer with matching bits is a genuine upgrade over a combi drill.
Matching the Bit to Your Brick and Your Fixing
Bit choice is not only about material. The diameter of the hole must match the wall plug or anchor precisely, and the condition of the brick affects how aggressively you can drill. Too small a hole means the plug will not seat, and forcing it splits the brick. Too large a hole means the plug spins and the fixing never tightens properly, which is a common cause of failed shelf brackets and wobbly TV mounts.
It also helps to know what you are drilling into. Modern perforated bricks, older soft red bricks, calcium silicate blocks, and engineering bricks all respond differently to impact drilling. The same bit can cut through one like butter and struggle badly in another, so treat the first hole as a test and adjust your technique from there.
Choosing the Correct Diameter for Wall Plugs
Most domestic fixings follow a predictable pattern. Red wall plugs typically need a 5mm or 5.5mm hole, brown plugs need 7mm, and blue plugs need 10mm. Grey or larger frame fixings often call for 8mm or 10mm. Always check the packaging rather than assuming, because manufacturers vary and a 0.5mm difference is enough to make a plug loose.
When in doubt, drill the smallest recommended size first and test-fit the plug. You can always enlarge a hole by a fraction of a millimetre, but you cannot shrink it. Using a bit that is slightly worn will produce an oversized hole, so if your 7mm bit has seen heavy use, measure a test hole in an offcut or an inconspicuous area before committing to a visible wall.
Brick, Mortar, Concrete, and Tile: Different Behaviour
Mortar joints are the softest part of a brick wall and will accept a masonry bit with minimal hammer action. Drilling directly into the mortar line is sometimes deliberate — it is easier, and on older properties with lime mortar it avoids cracking the bricks themselves. However, fixings in mortar have lower pull-out strength and should not be used for anything load-bearing.
Concrete and engineering brick are much harder and demand full hammer action plus a sharp carbide tip. Glazed tiles, porcelain, and natural stone are a different problem again: hammering will shatter them, so you need a masonry bit used in rotation-only mode, ideally starting with a small pilot hole. If you are drilling through tile into brick behind it, drill the tile without impact, then switch the hammer back on once you are through.
Technique, Troubleshooting, and Tool Care
Even the best bit will underperform with poor technique. Most failures — wandering holes, burnt tips, cracked bricks, and broken drill bits — trace back to speed, pressure, or the absence of a pilot mark. A few simple habits will noticeably improve your results and extend the life of your tooling.
Start by marking the hole precisely with a pencil, then create a small dimple with a centre punch, a nail, or the tip of a masonry bit tapped gently with a hammer. This prevents the bit from skating across the surface. Begin drilling at low speed with light pressure until the tip has bitten, then increase speed and let the hammer action do the work rather than leaning on the drill.
Managing Dust, Heat, and Hole Depth
Brick dust is abrasive and it packs into the flutes, which reduces cutting efficiency and traps heat. Withdraw the bit every few seconds to clear the flutes — a technique known as peck drilling — and let the bit cool briefly if it feels hot. Never touch the tip straight after drilling, and avoid dipping a hot bit in water, as thermal shock can crack the carbide.
Depth control matters too. Wrapping a piece of masking tape around the bit at the required depth gives you a clear visual stop and prevents drilling deeper than the plug needs. Once the hole is finished, blow or vacuum out the dust before inserting the plug, because debris stops the plug seating fully and can cause the fixing to bottom out prematurely.
Diagnosing Common Drilling Problems
A blue or discoloured tip means excessive heat from too much pressure or insufficient hammer energy, and the bit is usually finished. A hole that wanders off line suggests the bit was not started square or the drill was tilted mid-cut. Cracks radiating from a hole normally mean drilling too close to an edge, using a blunt bit, or applying heavy pressure on a fragile brick.
If progress is painfully slow, check that you are actually in hammer mode and that the bit is not worn. If the drill smokes or smells of burning, stop immediately. And if a hole has ended up oversized, do not simply push in a bigger plug that cracks the brick — fill it with a suitable resin or mortar repair, let it cure, and drill again at the correct diameter.
Get your bit selection and technique right and drilling brick becomes a routine task rather than a gamble. Keep a small set of sharp carbide bits in the sizes that match your most-used plugs, add an SDS rotary hammer to your kit if you drill masonry regularly, and replace worn bits without hesitation. Your walls will look cleaner, your fixings will hold firmly, and the next shelf, bracket, or cable run will take minutes instead of hours.