DIY Wooden Bathtub Cover: Elevate Your Bathroom with a Rustic Touch
Bringing a touch of rustic charm to your bathroom can be achieved with a simple yet striking DIY project: a wooden bathtub cover. Not only does it add a warm, inviting aesthetic, but it also provides functionality by keeping bath water warm and reducing splashing. Here's a comprehensive guide on creating your own wooden bathtub cover.
Before you dive into the materials and steps, let's address the elephant in the room. Can a wooden bathtub cover get wet? The short answer is yes, but it's crucial to use weather-resistant wood and properly treat it to ensure longevity. Now, let's get started.
Materials and Planning
Choosing the right wood is crucial. cedar, teak, and redwood are excellent options due to their natural resistance to rot and decay. We'll focus on cedar for this guide.



Here's a list of materials and tools you'll need:
- Cedar board (1x8, 8 feet long)
- External wood glue
- Clamps
- Polysческой oil (water-resistant)
- Safety glasses
- Tape measure
- Circular saw
- Hand sander (80-120 grit)
- Screws (1-1/4 inch, stainless steel)
- Screwdriver or drill
- Felt pads (1/8 inch thick)
Measure Your Bathtub
Measure the length and width of your bathtub. Standard tubs are typically 60 inches long and 32 inches wide, but it's always best to measure your specific tub.



Once you have the measurements, you can decide on the thickness of your wooden cover. A thickness of 1.5 inches provides a sturdy and aesthetically pleasing cover. Now, calculate the total amount of cedar board you'll need:
Length + Width + 1/2 inch (for overhang) = Total length of cedar board needed
Cut the Cedar Board
Use a circular saw to cut the cedar board according to your measurements. Ensure you wear safety glasses during this process.






The cut pieces should include two parts: the main cover (matching your tub's length and width) and two pieces for the overhang (each half an inch wider than your tub's length).
Assembling the Wooden Bathtub Cover
Now that you have your pieces cut, it's time to assemble the wooden bathtub cover.
Before you begin, lay out the pieces and decide which side will be the top of your cover. Then, apply external wood glue liberally to the edges of both pieces that will be joined together.

Glue and Clamp the Main Cover
Place the two main pieces together, ensuring they're flush and aligned. Use clamps to apply even pressure along the join.
Allow the glue to dry according to the package instructions. Ensure the clamps stay on until the glue is completely dry to achieve a strong bond.
Attach the Overhang Pieces
Once the main cover is dry, it's time to attach the overhang pieces. Apply glue to one side of each overhang piece and attach them to the longer sides of the main cover.
Use clamps again to ensure a tight bond. Let the glue dry completely before proceeding.
Finishing Touches
After the glue has dried, you can proceed with finishing the wooden bathtub cover.
Use a hand sander to smooth any roughness or uneven edges. Start with a coarse grit (80) to remove large imperfections, then finish with a finer grit (120) for a smooth surface.
Apply Polysíguezio Oil
Apply a generous amount of polysíguezio oil to the entire wooden cover using a soft brush or clean cloth. Allow it to soak in for 15-30 minutes, then wipe off any excess with a clean cloth.
Let the oil cure according to the manufacturer's instructions. This typically involves applying several coats, allowing them to dry and cure between applications.
Attach Felt Pads
To protect your bathtub surface, attach felt pads to the underside of the wooden cover. These will prevent scratching and allow for better grip.
Use screws (at least two per side) to attach the felt pads to the underside of the overhang pieces. Ensure the screws are long enough to grip the wood but not so long that they poke through the top side.
Now that you've finished your DIY wooden bathtub cover, it's ready to be placed on your tub. Enjoy the warmth and charm it brings to your bathroom! Regularly re-apply polysíguezio oil to maintain the wood's protection and appearance.





