DIY Vertical Gun Rack: Build a Space-Saving, Secure Storage Solution
If your gun collection is starting to crowd a closet or lean awkwardly in a corner, a DIY vertical gun rack can turn unused wall space into secure, organized storage. Vertical racks keep rifles and shotguns upright, make them easier to grab, and reduce the chance of scratches that happen when firearms bump together.
Building your own rack also lets you control the dimensions, finish, and security features instead of settling for a one-size-fits-all store model. With a few basic tools and a thoughtful plan, you can create a rack that fits your space, matches your budget, and keeps safety front and center.
Planning a Safe and Practical DIY Vertical Gun Rack
Before you cut a single board, take stock of what you need to store. Count rifles, shotguns, and any scoped firearms, then note the longest barrel and widest stock. A rack designed around your actual collection will feel intentional and work better than a generic plan that leaves wasted gaps or cramped slots.
Next, choose a wall that can handle the load and still allow reasonable access. Avoid damp basements, direct sunlight, and high-traffic areas where the rack could be bumped. Check local laws about firearm storage and display, especially if children or visitors are often in the home.
Choosing the Right Location and Wall Anchors
The best location is a dry, secure wall with at least one stud where the main weight will rest. Use a stud finder to locate framing, and remember that wall studs are usually spaced 16 or 24 inches apart. If you cannot hit two studs, plan to add a sturdy backer board that spans the studs before mounting the rack.
For heavy loads, lag bolts or heavy-duty structural screws driven into studs are far safer than drywall anchors alone. If you are mounting to concrete or brick, use masonry anchors rated for the total weight of the rack plus the firearms. When in doubt, overbuild the attachment and test the empty rack before loading it.
Selecting Materials and Tools
Hardwood boards such as oak or maple offer excellent strength, while 3/4-inch birch plywood is a practical choice for back panels and side supports. For the cradle pieces, 1x4 or 1x6 lumber works well because it is easy to cut, sand, and shape. Avoid thin or brittle materials that could split under the concentrated weight of a buttstock.
You will need a drill, stud finder, circular saw or handsaw, wood glue, screws, sandpaper, and a tape measure. A router or sanding drum can soften the notches, and felt, cork, or rubber stripping will protect the finish on your guns. Clamps help keep pieces aligned while glue dries, especially if you are assembling a multi-slot rack.
Building Your DIY Vertical Gun Rack Step by Step
A simple vertical rack usually consists of a back panel, two side supports, and two horizontal rails that hold the barrels and stocks. The lower rail cradles the buttstocks, while the upper rail supports the barrels or forends. This design keeps each firearm separated and makes the rack easier to mount securely.
Start by sketching a cut list based on your measurements. Leave at least 2 to 3 inches between slots for scoped rifles and wide stocks, and add a little extra height if you plan to store long-barreled shotguns. Dry-fit the pieces before final assembly so you can adjust spacing without wasting material.
Step-by-Step Assembly Basics
Cut the back panel and side supports to length, then mark the positions for the rails. If you want notched cradles, trace the curve of a typical stock or barrel and cut shallow U-shaped slots. Sand every edge smooth, especially inside the notches, because rough wood can wear away a firearm’s finish over time.
Assemble the frame with wood glue and screws, checking for square as you go. Attach the lower rail first, then the upper rail, and test the spacing with an empty rifle or a dowel. If the fit feels too tight, widen the notches slightly; if it feels loose, add padding or adjust the rail position before mounting.
Securing, Padding, and Locking Options
Mount the completed rack into wall studs using lag bolts or heavy-duty screws, and use washers to spread the load. Check that the rack is level and that every screw is snug but not so tight that it crushes the wood. Once mounted, gently load one firearm at a time to confirm balance and clearance.
Line the cradles with felt, cork, or closed-cell foam to prevent scratches and reduce movement. For added security, install a steel locking bar, a cable lock through the trigger guards, or a lockable cabinet door over the rack. Keep firearms unloaded, store ammunition separately, and use trigger locks or action-open flags as part of your routine.
With the rack mounted and padded, take a moment to label slots or add small hooks for accessories like cleaning rods or slings. A well-built vertical gun rack should feel solid, look tidy, and make your daily handling habits safer and more consistent. Start with a simple plan, measure twice, and build a setup that fits your collection now and can grow with it later.