diy motorcycle kickstand pad

DIY Motorcycle Kickstand Pad: Easy Guide to Protect Your Bike Anywhere

By Joseph Garcia
AD

A motorcycle kickstand is a marvel of leverage until the ground gives way. On a hot summer day, a small kickstand foot can sink into asphalt, and on gravel, grass, or loose dirt, it can disappear entirely. A DIY motorcycle kickstand pad is a simple solution: a small plate or puck you place under the side stand to spread the load. It takes up little space, costs almost nothing, and can be the difference between a stable parking spot and a very bad afternoon.

Store-bought kickstand pucks work, but making your own gives you control over size, shape, material, grip, and storage. You can build one from a hockey puck, scrap plastic, aluminum, or even a crushed can in an emergency. This guide walks through why a pad matters, which materials hold up, how to design one that stays put, and how to use it without adding clutter to your ride.

Why a DIY Motorcycle Kickstand Pad Makes Sense

Motorcycles concentrate a huge amount of weight on a tiny contact patch. A 500-pound bike might put 200 pounds or more through a kickstand foot no larger than a quarter or half-dollar. On soft ground, that pressure is enough to push the stand down, letting the bike lean farther than intended. A pad increases the surface area, lowering the pressure and keeping the stand on top of the surface instead of inside it.

AD
Motorcycle Kick Stand Pad
Motorcycle Kick Stand Pad
a close up of a skateboard with a seat on it's back end
a close up of a skateboard with a seat on it's back end
there is a motorcycle that has been placed on the ground with it's front tire
there is a motorcycle that has been placed on the ground with it's front tire

Beyond preventing a tip-over, a pad protects pavement. Hot asphalt, fresh sealcoat, and decorative concrete can be scarred by a kickstand. In some places, parking without a pad on soft ground can even be frowned upon. A DIY pad is cheap insurance that fits in a pocket, tool roll, or under the seat, and it can be customized to match your bike and riding style.

Everyday Parking Problems a Kickstand Pad Solves

The most common problem is heat. Asphalt becomes soft in direct sun, and a kickstand can punch through the surface within minutes. The bike then leans over, sometimes far enough to fall. A kickstand pad distributes the load so the stand rests on the pad, not on the softening pavement. The same principle applies to packed gravel, sand, and mud, where the stand can dig in and let the bike tip.

2013 スピード&カスタムショー # 79 ARROGANT LKNGE
2013 スピード&カスタムショー # 79 ARROGANT LKNGE
Motorcycle Side Kickstand Pad Anti-Slip Kick Stand Support Pad Universal For Kawasaki Honda Yamaha
Motorcycle Side Kickstand Pad Anti-Slip Kick Stand Support Pad Universal For Kawasaki Honda Yamaha
18 DIY Motorcycle Stand Projects For Everyone
18 DIY Motorcycle Stand Projects For Everyone

Consider a loaded touring bike parked on a shoulder in August, a dual-sport bike on a grassy campsite, or a cruiser on a gravel driveway. In each case, the kickstand foot is the weak link. A homemade kickstand pad gives you a stable, repeatable parking solution. It also helps when you need to park on a slope and want a little extra margin before the bike leans too far.

Cost, Customization, and Convenience Compared With Store-Bought Pucks

Retail kickstand pucks often cost between ten and thirty dollars. They are usually durable and effective, but many are bulky, brightly branded, and easy to leave behind. Some are too thick to fit comfortably in a jacket pocket, and others are too small to help in soft ground. A DIY motorcycle kickstand pad can be made for a few dollars or free from scrap, and you can size it to your exact kickstand foot and storage space.

AD

Customization is where DIY shines. You can drill a hole and add paracord, a small carabiner, or a retractable leash so the pad stays with the bike. You can paint it to match your helmet, add grip tape, or shape it to fit a specific cubby. You can make it thin enough for a back pocket or large enough for a heavily loaded adventure bike. That flexibility makes a homemade pad more likely to be carried and used, which is the only way it helps.

DIY $15 Motorcycle jack in 10 minutes / Lift / Harley-Davidson Fat boy
DIY $15 Motorcycle jack in 10 minutes / Lift / Harley-Davidson Fat boy
the front end of a motorcycle with a wrench on it
the front end of a motorcycle with a wrench on it
the front end of a vehicle with a wrench on it's axles
the front end of a vehicle with a wrench on it's axles
Motorcycle Kickstand Pad
Motorcycle Kickstand Pad
Before I fab my own...kickstand/side stand foot...
Before I fab my own...kickstand/side stand foot...
Make sure your bike remains upright
Make sure your bike remains upright

Choosing Materials and Designing Your Kickstand Pad

The ideal material spreads load without bending, resists heat, grips the kickstand, and stays light enough to carry. Thickness matters, but surface area matters more. A thin, wide plate usually works better than a thick, narrow block because it lowers ground pressure over a larger area. The pad also needs a top surface that keeps the kickstand foot from sliding, especially when the bike is parked on a slight incline.

Think about where you ride and park. If you commute and park on hot asphalt, choose a heat-resistant material. If you ride off-road, prioritize grip and a larger footprint. If storage is tight, focus on a compact shape. There is no single perfect material, but there are several proven options that work well for a DIY kickstand pad.

AD

Best Materials for a Homemade Kickstand Puck

A hockey puck is a classic choice. It is cheap, dense, grippy, and already puck-shaped. It resists impacts and provides a stable platform, though it can be thick for some pockets. UHMW plastic, often sold as cutting board material, is another excellent option. It is tough, weather-resistant, and easy to cut with woodworking tools. Scrap aluminum plate is lightweight and strong, but it can bend if too thin and may slide unless you add texture.

an alligator is laying on its back with it's mouth open
an alligator is laying on its back with it's mouth open
Motorcycle foot peg. #Rebar #Custom
Motorcycle foot peg. #Rebar #Custom
Build a cheap seat
Build a cheap seat

Other materials include hardwood blocks sealed with polyurethane, 3D-printed parts made from PETG, ABS, or ASA, and electrical junction box covers. For an emergency pad, a crushed aluminum can, a flat rock, or a chain link fence post cap can work in a pinch. Avoid brittle plastics that crack in cold weather, and avoid thin sheet metal that folds under weight. If you use wood, seal it so moisture does not rot or split it.

Design Considerations for Stability and Storage

A good kickstand pad should be at least three to four inches across for most motorcycles, with a top surface that captures the kickstand foot. You can route a shallow groove or add a lip to keep the foot from sliding. Rounded corners prevent the pad from snagging on pockets or punching through soft luggage. If the pad is too small, the kickstand may miss it entirely or slide off when the bike settles.

AD

Storage is just as important as stability. Drill a hole near one edge and attach a short paracord loop, a carabiner, or a retractable badge reel. Some riders keep the pad in a tank bag, others under the seat, and some clip it to a belt loop. Test the pad on your bike before you rely on it. Put the bike on the stand, apply a little weight, and check that the pad does not rock, flex, or slip. A pad you never carry is useless, so make it easy to grab and stow.

With a little scrap material and an hour of work, you can create a kickstand pad that fits your bike, your parking habits, and your storage needs. Start with a simple puck or plate, test it on hot asphalt and soft ground, and refine the shape until it feels solid every time you park. The next time you pull into a sunny lot or a grassy overlook, you will have a small, custom piece of gear that keeps your motorcycle upright and your mind at ease.

AD