Dimensions of Mercy Gun: Size, Specs, and What You Need to Know
If you have ever searched for the dimensions of the Mercy gun, chances are you were standing in front of a half-finished cosplay prop, a slicer preview in your 3D printing software, or a sketch that simply refused to look right on paper. In nearly every case, the phrase points to one specific object: the Caduceus Blaster, the white-and-gold sidearm carried by Mercy in Overwatch and Overwatch 2.
Blizzard has never released an official engineering drawing for that weapon, which is precisely why the question keeps resurfacing in cosplay forums, prop-making groups, and printing communities. What follows is a practical breakdown of the real-world measurements builders actually use, how those numbers were derived, and how to adapt them to your own hands, printer bed, and convention rules.
What Exactly Is the Mercy Gun?
The "Mercy gun" is the Caduceus Blaster, the compact backup weapon that Mercy (Dr. Angela Ziegler) draws when her healing beam is not the right tool for the moment. It is a support-class sidearm with a rounded emitter, a swept grip, and a clean medical-inspired silhouette that reads as futuristic without tipping into military realism.
Because the weapon exists only as a digital asset, its dimensions are not fixed by any manufacturer's spec sheet. Every set of numbers floating around the community comes from one of three sources: measurements taken from ripped game models, hand-scaled estimates from cosplayers matching the gun to a human body, or physical measurements of finished props that were later reverse-engineered.
Design Origins and Visual Anatomy
The design language borrows from Swiss precision instruments and Valkyrie motifs rather than from conventional firearms. The chassis is a smooth white ceramic or composite shell, broken up by gold trim, soft pink-white energy channels, and a caduceus wing emblem near the rear housing. Nothing about it looks mass-produced or gritty.
Physically, the blaster breaks into a handful of recognizable zones: the emitter shroud at the front, the slide-like upper housing that houses the energy channel, the trigger guard, the swept grip with its textured panels, the magazine base at the bottom of the grip, and a small holographic display element near the rear sight line. Knowing these zones matters, because each one has its own measurement profile and its own printing challenges.
Why Dimensions Matter for Cosplay and 3D Printing
A prop that is ten percent too large looks subtly wrong in photos and feels clumsy in the hand during a three-hour convention. A prop that is ten percent too small looks like a toy and creates an uncanny mismatch against the scale of a human arm. Getting the size right is the difference between a costume that reads instantly and one that people squint at.
There are practical constraints too. Most consumer printers have a build volume somewhere between 220 and 300 millimeters on the longest axis, so a full-length blaster often has to be split. Knowing the true overall length tells you exactly how many cuts you need, where the seam lines should fall, and whether a scaled-down version at 85 or 90 percent will fit on the plate in one piece.
Breaking Down the Measured Dimensions
Measurements for a prop like this are usually expressed as a bounding box: the longest dimension front to back, the tallest dimension top to bottom, and the widest dimension side to side. Community-built Caduceus Blasters, when matched to an average adult wearer, tend to cluster in a fairly narrow range.
It is worth stating plainly that these are community-derived approximations rather than official figures. Treat them as a strong starting point, then verify against reference images and your own body proportions before committing filament or resin to the project.
Overall Length, Height, and Width
The overall length, measured from the tip of the emitter to the rearmost point of the housing, generally lands between 240 and 260 millimeters, or roughly 9.4 to 10.2 inches. That places it in the same footprint as a large-frame semi-automatic pistol, longer than a compact carry gun but noticeably shorter than a full-size rifle accessory.
The overall height, from the top of the emitter shroud down to the base of the magazine, typically runs 160 to 180 millimeters, or about 6.3 to 7.1 inches. Width is where the blaster stays surprisingly slim: 45 to 55 millimeters across the widest point, usually at the grip or the rear housing.
- Overall length: 240-260 mm (9.4-10.2 in)
- Overall height: 160-180 mm (6.3-7.1 in)
- Maximum width: 45-55 mm (1.8-2.2 in)
- Grip length: approximately 105-115 mm
- Emitter shroud diameter: approximately 50-60 mm
Grip, Emitter, and Detail Measurements
The grip is the part your hand actually judges, so it deserves its own attention. A comfortable grip for most adult hands runs about 105 to 115 millimeters from the top of the backstrap to the magazine base, with a circumference in the neighborhood of 130 to 150 millimeters. If your grip comes out much thinner than that, the prop will feel hollow and unconvincing when held.
The emitter shroud at the front is the visual anchor of the whole design. Its outer diameter typically measures 50 to 60 millimeters, with a recessed inner opening that reads as the muzzle. The trigger guard should have enough internal clearance to fit a gloved finger without pinching, and the rear housing usually sits slightly wider than the slide section to give the silhouette its distinctive stepped profile.
Turning Those Numbers Into a Build
Numbers on a page only become useful once they interact with a real body and a real printer. The first decision is scale: do you build at 100 percent, or do you adjust based on your own height and hand size? A shorter cosplayer often benefits from a 90 to 95 percent scale, while a taller performer may want to push slightly past 100 percent to keep the silhouette balanced.
The second decision is fidelity. A display piece that lives on a shelf can carry fine detail and a fragile emitter tip. A convention prop that gets holstered, swung around, and bumped into crowds needs thicker walls, reinforced seams, and a design that forgives accidental impact.
Scaling, Printing, and Assembly Tips
Split the model along natural seam lines rather than cutting through the middle of the emitter. The transition between the shroud and the upper housing, and the junction between the grip and the frame, are ideal places to hide a joint. Use alignment pins or keyed slots so the parts register correctly during gluing, and leave a small tolerance gap of roughly 0.2 to 0.3 millimeters on mating surfaces.
Print orientation matters more than most people expect. Parts printed flat tend to show layer lines across the most visible curves, so rotate the emitter shroud to print vertically and accept the support cleanup in exchange for a smoother front face. After assembly, fill the seams with spot putty, sand progressively from 220 up to 800 grit, and prime before color.
Weight, Materials, and Convention Safety
Material choice drives both durability and how the prop feels in hand. PLA is rigid, cheap, and paints beautifully, which makes it ideal for a display piece. PETG handles impact and heat better, which matters if the prop will sit in a hot car between events. Resin printing delivers the sharpest detail on small elements like the caduceus emblem, but resin is brittle and should be reserved for accent parts.
Aim for a finished weight between 500 and 800 grams, achieved with two to three perimeter walls and 15 to 20 percent infill. That range feels substantial without tiring your wrist. For convention safety, fit an orange tip, avoid any functional trigger mechanism, and check the specific prop policies of the event you plan to attend, since rules on replica firearms vary widely between venues.
Whether you are printing your first Caduceus Blaster or refining a version you have already carried through three conventions, the measurements are only the beginning of the conversation. Print a rough draft at low infill, hold it in your hand, photograph it against your costume, and let your own proportions tell you where the numbers need to flex. The best Mercy gun is not the one that matches a spreadsheet exactly, but the one that looks like it belongs in your grip.