Delta Mortising Attachment: Turn Your Drill Press Into a Mortising Machine
A Delta mortising attachment is one of those quiet shop upgrades that can change how you build furniture. Instead of buying a standalone hollow chisel mortiser, you mount this accessory on a compatible Delta drill press and use the drill press quill to drive a hollow chisel and bit through wood. The result is a clean, square-walled mortise ready for a tenon.
The appeal is obvious: you save floor space, spend far less than a dedicated machine, and add serious joinery capability to a tool you already own. The catch is that a drill press mortising attachment is only as good as its setup. Alignment, bit protrusion, feed rate, and chip clearance all matter, and a few minutes of tuning can be the difference between tight joinery and a burned, oval hole.
What a Delta Mortising Attachment Is and How It Works
In simple terms, the Delta mortising attachment converts a drill press into a hollow chisel mortiser. The attachment usually includes a chisel holder that clamps around the drill press quill, a fence and hold-down that mount to the table, and sometimes a set of hollow chisels and bits. You still use the drill press chuck to hold the auger bit, while the attachment keeps the square chisel stationary and aligned.
Because the quill moves up and down without rotating, it is the perfect place to mount a non-rotating chisel holder. The bit spins inside the hollow chisel, cutting away most of the waste, and the chisel's square edges shear the corners. This is why the system cuts a true square hole rather than a round one. Delta's version was designed for their own drill presses, though some attachments can fit other brands if the quill diameter and mounting geometry match.
How the Hollow Chisel System Cuts Square Holes
A hollow chisel mortising bit is actually two cutters working together. The auger bit drills a round hole and lifts chips out of the mortise, while the hollow chisel follows behind and squares the sides and corners. The chisel does not spin; it is held firmly by the attachment. The bit must protrude slightly below the chisel so it can drill ahead and prevent the chisel from burning or stalling.
That protrusion is typically around 1/16 inch to 3/32 inch, depending on the chisel size and wood species. Too little protrusion and the chisel rubs, overheats, and cuts slowly. Too much and the bit wanders, the chisel may not clear chips, and the mortise walls can become rough. When everything is set correctly, the chisel slices clean corner fibers, and the bit ejects most of the waste through the chisel's side opening.
Compatibility and What You Need Before Installing
Before you buy a used Delta mortising attachment, confirm that it fits your drill press. The critical dimensions are the quill diameter and the spindle travel. The chisel holder must clamp securely around the quill without slipping, and the drill press needs enough quill travel to cut the mortise depth you want. A drill press with short quill travel will limit you to shallow mortises unless you reposition the workpiece and cut from both sides.
You will also need a drill press with a chuck that accepts the bit shank, usually 1/2 inch or smaller depending on the chisel size. A stable table, a good fence, and a hold-down are essential because the workpiece must not lift or shift during the cut. Sharp chisels and bits are non-negotiable. Dull tooling is the fastest way to burn wood, break bits, and blame the attachment for a problem that starts with edge geometry.
Setting Up, Using, and Evaluating the Delta Mortising Attachment
Setting up the Delta mortising attachment is not difficult, but it is fussy. You are aligning three separate systems: the rotating bit, the stationary chisel, and the fence that guides the workpiece. If any one of them is off, the mortise will be oversized, tapered, or rough. The good news is that once you establish a repeatable setup, you can cut a batch of mortises with consistent results.
The attachment shines for occasional furniture projects, small cabinet runs, and repair work where a dedicated mortiser would be overkill. It is less appealing for production work, deep mortises in hardwoods, or jobs that require constant size changes. Understanding those boundaries helps you decide whether to hunt down a Delta attachment or invest in a standalone hollow chisel mortiser.
Step-by-Step Installation and Alignment
Start by unplugging the drill press. Raise the table and clean the quill so the chisel holder can clamp squarely. Install the chisel holder on the quill according to the manufacturer's instructions, then insert the auger bit into the chuck. Slide the hollow chisel over the bit and into the holder, but do not tighten it yet. Adjust the bit so it protrudes below the chisel by about 1/16 inch to 3/32 inch, then lock the chisel in place with the set screw.
Next, mount the fence and hold-down to the drill press table. The fence should be parallel to the chisel's flat side, and the hold-down should press the workpiece down without interfering with the chisel. Set the drill press speed to roughly 500 to 800 RPM for most 1/4-inch to 3/8-inch chisels, and slower for larger sizes. Set the depth stop to your desired mortise depth. Make a test cut in a scrap piece of the same wood. Check the mortise for squareness, size, and burn marks. Adjust the fence, bit protrusion, and feed technique until the test mortise is clean and consistent.
Techniques for Clean Mortises, Benefits, and Limitations
For clean results, mark the mortise layout clearly and use stop blocks or a fence to position each cut. Plunge slowly and steadily, letting the bit clear chips. Withdraw the chisel frequently to prevent packing, especially in resinous or damp woods. Cut overlapping holes along the mortise length, then make a final pass to smooth the walls if needed. A backer board under the workpiece reduces tear-out on the bottom face and protects the drill press table.
The Delta mortising attachment's biggest benefits are cost, space savings, and versatility. It turns a drill press into a square-hole machine for a fraction of the price of a dedicated mortiser, and it stores on a shelf when not in use. Its limitations are equally real: setup takes time, quill travel limits depth, the fence may flex under heavy feed pressure, and the drill press lacks the foot pedal and rack-and-pinion control of a dedicated machine. For a few dozen mortises a year, that trade-off is often worth it. For daily production, a dedicated hollow chisel mortiser or a router-based mortising jig may be the better path.
If you already own a compatible Delta drill press, a Delta mortising attachment can be a rewarding addition to your shop. Take the time to align it properly, keep the chisels sharp, and practice on scrap before you commit to a project. Once you dial it in, you can cut mortise-and-tenon joints that feel solid and look clean, without giving up valuable floor space. Keep an eye on the used market for a complete setup, and consider adding a few replacement chisels and bits so you are ready for the next furniture build.