Craftsman Model 917 Drive Belt: Best Replacement Guide & Top Picks
If your Craftsman model 917 riding mower suddenly feels sluggish, smells like burning rubber, or refuses to climb a slight slope, the drive belt is one of the first components to inspect. This belt transfers engine power to the transaxle so the tractor can move forward and reverse, and when it wears out, stretches, or slips, the machine may still start and run perfectly while going nowhere. Knowing which belt you need, how to inspect it, and how to replace it can save you a costly repair bill and get you back to mowing faster.
The Craftsman 917 label covers a wide family of lawn tractors and garden tractors built by American Yard Products, so “model 917” alone is not enough to order the right belt. You need the complete model number from the serial plate, plus an understanding of whether you are replacing the transmission drive belt or the mower deck belt. Both are critical, but they serve different systems and have different symptoms when they fail. This guide breaks down the identification, inspection, replacement, and maintenance process in practical terms.
Understanding the Craftsman Model 917 Drive Belt
The 917 prefix is a manufacturer code, not a single tractor model. Craftsman used it across many years and dozens of variations, including 917.270, 917.271, 917.272, 917.273, 917.274, 917.275, 917.276, 917.277, 917.278, 917.279, and numerous 917.28xxxx series tractors. Each of those machines can use a different belt length, width, and routing path. That is why a belt advertised as “fits Craftsman 917” may still be wrong for your specific tractor if you do not verify the full model and serial number.
The drive belt, also called the ground drive belt or transmission belt, runs from the engine pulley to the transaxle pulley, usually passing around one or more idler pulleys and a tensioner. It is separate from the deck belt, which spins the mower blades. A failing drive belt typically causes movement problems: slow engagement, slipping under load, a burning smell, or a tractor that will not move at all. A failing deck belt usually causes cutting problems: blades stop spinning, uneven cut, or a belt that jumps off the pulleys.
Locating the Correct Belt for Your Specific 917 Model
Start by finding the model and serial number plate. On most Craftsman 917 tractors, it is located under the seat, on the rear fender, or on the frame near the back of the machine. The full model number usually looks like 917.XXXXXX, and the serial number helps identify the production year. Once you have that information, look up a parts diagram for your exact tractor. The diagram will show the correct OEM part number and the proper belt routing, which is essential because even a belt of the same length can fail if it is routed on the wrong side of an idler pulley.
Aftermarket belts from brands such as Gates, Stens, Oregon, and Arnold can be excellent alternatives, but you must cross-reference the OEM number or match the belt dimensions precisely. Measure the old belt’s outside circumference, top width, and cross-section if no part number is visible. Many Craftsman 917 drive belts are 1/2-inch wide, but lengths vary widely by model and deck size. A belt that is too short will be nearly impossible to install and will overload the bearings, while a belt that is too long will slip, flap, and wear out quickly.
How to Inspect and Diagnose a Failing Drive Belt
Inspect the drive belt with the engine off, the spark plug boot disconnected, and the parking brake engaged. Look for glazing, cracks, frayed edges, missing chunks, and shiny spots that indicate slipping. A belt can look intact on the outside while the inner cords are stretched or broken. Check the pulleys for rust, nicks, or bent flanges, and spin each idler pulley by hand. It should turn smoothly without grinding or wobbling. If a pulley binds or wobbles, replacing only the belt will lead to another failure.
Diagnostic symptoms can help you narrow down the problem. If the tractor moves slowly but the engine revs normally, the belt may be slipping due to wear or weak tension. If you smell burning rubber after a few minutes of mowing, the belt is likely rubbing or slipping against a stuck pulley. If the belt repeatedly jumps off, check alignment, idler spring tension, and the routing diagram. On many 917 models, a stretched belt combined with a worn idler spring is the root cause, so replacing both at the same time is a smart preventive move.
Replacing and Maintaining a Craftsman 917 Drive Belt
Replacing a Craftsman 917 drive belt is a manageable DIY job for most homeowners, but it does require patience and attention to safety. Work on a level surface, disconnect the spark plug wire, turn off the fuel supply, and let the engine cool completely. If your tractor has a mower deck, you will likely need to remove it to access the drive belt and transmission pulleys. Take clear photos of the belt routing before you remove anything, because a single misrouted belt can cause major frustration later.
Gather the right tools before you start: a socket set, open-end wrenches, pliers, a pry bar or belt tension tool, jack stands, and a flashlight. Some models require removing the battery, fuel tank, or fender pan to reach the transaxle pulley. Others have an access panel or require lowering the deck. Always consult your model’s service manual or parts diagram for the exact sequence. The goal is to relieve tension safely, remove the old belt without forcing it, and install the new belt so it seats fully in every pulley groove.
Step-by-Step Drive Belt Replacement Tips
Begin by removing the mower deck if it blocks access to the drive belt. Disconnect the deck lift linkage, PTO clutch cable, and any belt covers. Release tension from the idler pulley using a wrench or pry bar, then slip the old belt off the engine pulley and transaxle pulley. Compare the old belt to the new one before installation; they should match in length, width, and cross-section. If they do not match, stop and verify the part number, because installing the wrong belt can damage pulleys or the transaxle.
Route the new belt exactly as shown in your diagram. It must sit inside the correct pulley grooves and on the correct side of every idler. On many Craftsman 917 tractors, the belt goes around the engine pulley, under or over a stationary idler, around the transmission pulley, and then against the tensioner pulley. Once routed, apply tension and rotate the engine pulley by hand to make sure the belt tracks smoothly. Reinstall all guards, reconnect the deck, and test the tractor at low speed before engaging the blades. Listen for squealing and check that the belt stays centered on the pulleys.
Belt Maintenance and Longevity Practices
Keep the drive belt area clean and dry. Grass clippings, dirt, and oil can accelerate wear and cause slipping. After every 25 hours of use, inspect the belt for cracks, glazing, and proper tension. Check the idler pulleys and tensioner spring at the same time. A weak spring allows the belt to slip, which overheats it and shortens its life. If you notice the belt squealing when you engage the transmission, stop and investigate immediately rather than continuing to mow.
Use OEM or high-quality aftermarket belts rather than generic hardware-store replacements. Cheap belts often have the wrong profile or insufficient strength for the load, and they may fail within a few mowing sessions. Avoid abrupt starts and stops, let the engine warm up before driving, and do not mow wet, heavy grass that overloads the drive system. Keeping a spare belt on hand is also wise, especially if you depend on your Craftsman 917 for regular lawn maintenance. With proper care, a quality drive belt can last several seasons.
With the right belt installed and tension set correctly, your Craftsman 917 should feel responsive and reliable again, whether you are climbing a slope or pulling a cart. Keep your model number saved, inspect the belt before each mowing season, and replace worn idler pulleys before they take out a new belt. A little routine attention now will keep your tractor moving smoothly for years of yard work ahead.